Mounting bracket (frame flat) - article No. 1015W1001: Mounting bracket (frame flat) w/M4 nuts - article No. 1015W9009: Drawing No.: 1015W4001 Drawing No.: 1015W4009 CO65 - mounted on frame: Release hook Very small built-in dimension: Height: min.
Mounting instructions (Example CO65 with LA40) When mounting the control box onto the actuator (1) Simply slide on the bracket until you hear a clear click (2) Slide on the control box until you hear a click and the box is mounted (3) It is recommended that the CO65 is mounted in a position that allows water to escape. Recommended torque: 0.6 Nm +/-0.
Mounting of cables and cable lock: CO65 has a uniquely designed cable lid. The lid also works as an integrated cable lock when closed. 1) Mount cable plugs in control box 2) Close lid until lock snaps into place (see arrows) To allow free access to the cables, the lid has a rest position when completely opened. It is possible to remove the lid by lifting it a few degrees and pulling it away from the housing under tight mounting conditions.
Recommendations • To avoid unintended activation of actuators if hand control cables short-circuit, LINAK recommends to use an OpenBus system (CO65). • If there is a risk that the system is overloaded and therefore shuts down thermally, LINAK recommends to use quick release actuators. These will allow functions to be lowered manually in case of a CO65 malfunction due to misuse/abuse.
15. CO71 (MEDLINE® CARELINE® ) The LINAK control box CO71 offers a consolidated range of unprecedented features – all utilising standardised technology, interfaces and compatibility. The CO71 for LINAK actuators is intended for the control of, for example, hospital bed movement.
Mounting bracket (frame flat) - article No. 1015W1001: Mounting bracket (frame flat) w/M4 nuts - article No. 1015W9009: Drawing No.: 1015W4001 Drawing No.: 1015W4009 CO71 - mounted on frame: Release hook Very small built-in dimension: Height: min.
Mounting instructions (Example CO71 with LA40) When mounting the control box onto the actuator (1) Simply slide on the bracket until you hear a clear click (2) Slide on the control box until you hear a click and the box is mounted (3) It is recommended that the CO71 is mounted in a position that allows water to escape. Recommended torque: 0.6 Nm +/-0.
Mounting of cables and cable lock: CO71 has a uniquely designed cable lid. The lid also works as an integrated cable lock when closed. 1) Mount cable plugs in control box 2) Close lid until lock snaps into place (see arrows) To allow free access to the cables, the lid has a rest position when completely opened. It is possible to remove the lid by lifting it a few degrees and pulling it away from the housing under tight mounting conditions.
Recommendations • To avoid unintended activation of actuators if hand control cables short-circuit, LINAK recommends to use an OpenBusTM system (CO71). • If there is a risk that the system is overloaded and therefore shuts down thermally, LINAK recommends to use quick release actuators. These will allow functions to be lowered manually in case of a CO71 malfunction due to misuse/abuse.
16. OPS - OpenBus Power Supply (MEDLINE® CARELINE® ) The LINAK OpenBus Power Supply (OPS) is intended to control up to three heat pads. The OPS is equipped with 120 W constant power and comes as IPX6 Washable DURATM. The OPS offers flexible system combinations and can be used as a stand-alone system or as add-on to the existing LINAK CO control box solution as CO-Link™.
Mounting of cables and cable lock: The OPS has a uniquely designed cable lid. The lid also works as an integrated cable lock when closed. 1) Mount cable plugs in the OPS 2) Close lid until lock snaps into place (see arrows) To allow free cable access, the lid has a rest position when completely opened. It is possible to remove the lid by lifting it a few degrees and pulling it away from the housing under tight mounting conditions.
Recommendations • LINAK recommends safe cabling to avoid cable damage caused by pulling. • A product review as to current cut-off limits must be requested by the sales department. • Always use matching cable plug for the respective product. • Push plugs fully into correct sockets and make sure they are firmly inserted. • Mount the OPS box lid and close lid until locked in place. Heat pad cable Always use 6-wire cables.
17. PJ2 (MEDLINE® CARELINE®) The LINAK Power Junction Box PJ2 offers two extra outputs for the COXX control box series. Standardised technology, interfaces and compatibility like the new COXX control boxes. The PJ2 for LINAK actuators is intended for the control of, for instance, hospital bed and surgery tables movement.
Mounting bracket (frame flat) - article No. 1015W1001: Mounting bracket (frame flat) w/M4 nuts - article No. 1015W9009: Drawing No.: 1015W4001 Drawing No.: 1015W1009 It is recommended that the PJ2 is mounted in a position that allows water to escape. Recommended torque: 0.6 Nm +/- 0.
Mounting instructions (Example PJ2 with LA40) When mounting the control box onto the actuator (1) Simply slide on the bracket until you hear a clear click (2) Slide on the control box until you hear a click and the box is mounted (3) Cables PJ2 has a uniquely designed cable lid. The lid also works as an integrated cable lock when closed. 1) Mount cable plugs in control box 2) Close lid until lock snaps into place (see arrows) To allow free access to the cables, the lid has to be removed.
Recommendations • If there is a risk that the system is overloaded and therefore shuts down thermally, LINAK recommends using quick release actuators. These will allow functions to be lowered manually in case of a PJ2 malfunction due to misuse/abuse. • If the customer has other essential performance than “no unintended movement”, he must consider this in his own risk analysis. LINAK disclaims any liability.
6. Information on specific controls 1. ABL (MEDLINE® CARELINE®) With the small ABL print it is possible to convert analogue input to Bluetooth Low Energy. The ABL print can be used as attendant control or hand control integrated in side rails in for instance healthcare applications and offers easy access to different positioning functions.
ABL pairing Direct Pairing button similar to FS3BLE Direct Pairing can also be initiated by activating pin 3 and 4 on J2 and pin 2 on J3 simultaneously. Confirm on pin 3, J2. ABL - Commands and Pairing Function Details Direct Pairing Activation To enter Direct Pairing mode.
Mounting When mounting the PCBA print in a housing be aware of the minimum recommended distance between antenna and housing – see drawings below. The housing material should be non-conducting due to the BLE signal. The customer is responsible for testing and ensuring the BLE performance/range of the final system. Keep out zone (K.O) Seen from above p out zone (K.O). Seen from above K.O. Vertical ≥ 3,5mm Antenna Keep out zone (K.O) Side view PCB Keep out zone (K.O). Side view K.O.
2. ACC (MEDLINE® CARELINE®) The ACC (Attendant Control Compact) is fitted to advanced hospital and patient care beds for use where patient positioning must be carefully controlled by medical staff. 3. ACK (MEDLINE® CARELINE®) With the OpenBusTM system it is possible to use ACK membrane front covers as attendant control or hand controls integrated in the bed side rails. There are two different variants of ACK: ACK1 and ACK3.
5. ACO (MEDLINE® CARELINE®) The Attendant Control OpenBusTM (ACO) is a cost optimised and compact unit with up to 21 buttons that can be used as hand control keys or lock-outs. The lock-out function can be made visable by using yellow LEDs.
7. ACT (MEDLINE® CARELINE®) The Attendant Control Touch (ACT) for the hospital and care segment is a control panel with an intuitive, graphical three-level user interface: 1. Care mode for caregivers and relatives (bed operation) 2. Extended care mode for caregivers (extended bed operation, features, settings) 3. Service mode for technicians (advanced settings) The ACT combines several operations and functionalities in one unit, thereby eliminating the need for several hand controls on the individual bed.
When mounting: • LINAK recommends to use a self-tapping screw, BN84229, 50x12. • Please observe that the 1.5 [Nm] screw torque limit is not exceeded. • Please be aware that the screw holes in the ACT are only 11 mm deep. Use appropriate screws. • Please ensure that the mounting leaves space (2 mm) between the ACT and the back of the housing. This to avoid that water is trapped. The space is only necessary where the membrane is placed on the ACT.
8. DPH Medical (MEDLINE® CARELINE®) The desk panel control DPH is made especially for the medical segment. It makes it possible to differentiate product design and achieve a more aesthetic control solution. The DPH (DPH1K10-210007) works with MJB (MJB5061101-00) and is OpenBus™ compatible. The DPH (DPH1K10-210008 and DPH1K10-210009) fits directly into the analogue control box (CA30/CA40 or CA63). The MJB 000 port repeater version can be used in systems where several DPH controls are needed.
9. FPP (MEDLINE® CARELINE®) The FPP is for use with a variety of different bed types and is therefore compatible with control boxes that use an OpenBus™ interface. Usage: • Operation temperature: • Storage temperature: • Relative humidity: • Atmospheric pressure: • Flammability rating: • Approvals: +5 °C to +40 °C -10°C to +50 °C 20% to 80% non-condensing 700 to 1060 hPa (3000 m) V2 IEC 60601-1:2005 (Edition 3) ANSI/AAMI ES60601-1:2005 CAN/CSA-C22.2 No.
As illustrated in the pictures below the panel itself can be moved and angled in a number of positions. The arm can also be bent to move it closer or move it further away from the user. The lock function Between the arm and the panel there is a lock/unlock function, (a hose type connection). It enables the user to turn the panel into a preferred position. Locking of the panel: Turn the panel to a preferred position. With one hand on the panel turn the hose clockwise with the other hand.
11. FS3 (MEDLINE® CARELINE®) FS3 Floor adaptor The LINAK® Foot Switch FS3 is an elegant control unit, allowing healthcare professionals across the sector to have both hands free when attending to patients, thus also helping to improve ergonomics. It is designed to be used in modular adjustment systems consisting of LINAK control boxes and electric LINAK IC actuators.
Functionality Functionality overview analogue: Left pedal Code nos.
Functionality overview wireless 2nd left pedal Code nos. Single right pedal + - + - Key Mapping Key 4 Key 3 Key 2 Key 1 FS34AS5 N/A N/A I0 I1 FS34BS5 N/A N/A I10 I11 I21 FS34CS5 N/A N/A I20 FS35A55 I2 I3 I0 I1 FS35B55 I12 I13 I10 I11 FS35C55 I22 I23 I20 I21 The same software is used in both pedal 1 and 2 setups. The single pedal is always the BLE master with software. The 2nd pedal is a standard analogue FS3 driven by a single pedal.
Batteries What batteries to use The FS3 Wireless must be equipped with two AAA batteries. Due to the availability of AAA batteries, we recommend that you buy the batteries locally. If you prefer to buy from LINAK A/S, the LINAK part number is: 0063010. How to mount batteries correctly 1. Underneath the FS3 Wireless. Remove Phillips screws and remove battery cover. 2. Place batteries correctly to ensure the electrical polarity and place battery cover again. 1. 2.
12. HB30 (MEDLINE® CARELINE® ) The HB30 hand control is designed for better user experience and ergonomic fit for the hands of caregivers. The compact size ensures one hand operation. The HB30 is especially suitable for patient lifts and other MEDLINE® and CARELINE® applications like couches, tables and chairs for treatment and examination. The HB30 is available in an analogue version and an OpenBus™ version.
13. HB70 (MEDLINE® CARELINE®) The HB70 offers simultaneous drive of multiple actuators which can be used for the memory options. The hand control HB70 can be used for both OpenBus™ and analogue systems and comes in 3 colours: black, dark grey and light grey. Usage: • Compatible with most LINAK control boxes. • Approved according to: EN 60601-1, EN 60335-1 and UL 60601-1 as part of a LINAK actuator system Recommendation • • • • It is not possible to combine HB7x with the binary based CB9..PM/PN.
15. HB100 (MEDLINE® CARELINE®) The HB100 is an intelligent hand control with the LINAK® Weighing Solution. It features a 2.4” colour display with a full navigation menu keypad, thus allowing the display to be dynamic without physically having to change the hand control. The HB100 will automatically scan the system and only show the features available to create a user-friendly experience.
16. HB190 (MEDLINE® CARELINE®) The HB190 is an advanced hand control designed for high-end medical equipment. It contains 9.5 rows, giving the care staff 19 buttons for activation. It is equipped with 21 LEDs, providing user-friendliness due to the clear overview of the battery status, locking status and service indication. Furthermore, the HB190 comes with an exchangeable cable and is IPX6 Washable DURA™, ensuring a long product lifetime.
17. HB200 (MEDLINE® CARELINE®) The HB200 Wireless is a Bluetooth Low Energy (BLE) hand control for the medical and beds segments. It is available with 3 to 5 rows and locking of individual channels by using a magnet key. One LED will function as pairing and battery indicator.
