Datasheet

ManualsBrandsLinak ManualsAutomationLinear Drive 24 VDC

PRODUCT DATA SHEET

ACTUATOR

LA36

Features:

• 12, 24 or 36 V DC Permanent magnetic motor

(IC only 12/24 V DC)

• Thrust from 500 N - 10.000 N depending on gear ratio

and spindle pitch

• 10.000 N actuator cannot be ordered without

electrical endstop

• Heavy duty aluminium housing for harsh conditions

• Highly efﬁ cient acme thread spindle

• Protection class: IP66 for outdoor use (dynamic),

furthermore the actuator can be washed down

by a high pressure cleaner (IP69K – static)

• Hand crank for manual operation

• Integrated brake, high self-lock ability

• Endplay – 2 mm max.

• Non rotating piston rod eye

• Back ﬁ xture turnable in steps of 30 degrees

• Noise level: 73dB (A) measuring method DS/EN ISO 8746

actuator not locked

Options in general:

• Built in endstop switches

• Adjustable magnetic sensors for endstop signals

(code no. 1017031)

• Max. speed up to 160 mm/sec. depending on load and

spindle pitch

• Mechanical overload protection through integrated

slip clutch

• Hall effect sensor

• iFLEX options including IC, Parallel and BUS

• Mechanical potentiometer (not with IC)

• Analog or digital feedback for precise positioning

• Endstop signals (not potential free)

• Exchangeable cables in different lengths

• Different back ﬁ xtures and piston rod eyes

• When ordering AISI (304 and up) piston rod eye and

back ﬁ xture, stainless steel screws are automatically

included

Usage:

• Duty cycle at max. load 20% (up to 600 mm stroke, for

strokes between 601- 999 mm the max. duty cycle is

15%) at ambient temperature 25°C.

N.B. 10.000N 5% duty cycle.

• Ambient operating temperature -30°C to +65°C, full

performance from 5 - 40°C

• For applications operated at constant low temperatures

it might be beneﬁ cial to recommend a stronger version

of the LA36. This recommendation is done to reduce

the current consumption that in some combinations

can be up to 3 times higher than at normal conditions.

See TRD4187 and TRD4262

LA36 is ideal for use in harsh conditions. It is a solid

and powerful actuator based on the philosophy

that it must be able to operate under extreme

conditions. The actuator is ideal for mobile “off-

highway” equipment such as agricultural, forestry

and construction machines.

oto

on gear ratio

out

conditions

amic),

)

S/E

874

iFLEX is a descriptive term under which every

TECHLINE

actuator with built-in intelligence

is unified.

For more information on iFLEX, please see:

www.linak.com/techline

Summary of content (16 pages)

PAGE 1
P R O D U C T D ATA S H E E T ACTUATOR LA36 Features: • 12, 24 or 36 V DC Permanent magnetic motor (IC only 12/24 V DC) • Thrust from 500 N - 10.000 N depending on gear ratio and spindle pitch • 10.
PAGE 2
LA36 Load versus Stroke Length 10000 Load - Push (N) 6800 4500 N.B. LA36 500 - 1.700 N is with 20 mm spindle pitch LA36 500 - 6.800 N is with 12 mm spindle pitch LA36 500 - 10.000 N is with 8 mm spindle pitch 2600 1700 500 0 200 400 600 800 1000 Stroke Length (mm) • For applications that only operate in pull the limitations are 999 mm stroke and 10,000 N load.
PAGE 3
Speed and current curves: LA36 12V motor speed vs. load LA36 12V motor current vs. load 25 20mm/ 20mm/ F gear 12mm/ F gear E gear 160 140 Speed (mm/s) Ampere 20 180 8mm/ H gear 12mm/ H gear 12mm/ G gear 15 10 5 0 0 2000 4000 6000 8000 10000 20mm/ E gear 120 100 80 20mm/ F gear 12mm/ F gear 60 40 20 12000 12mm/ G gear 12mm/ H gear 8mm/ H gear 0 Load (N) 0 2000 4000 6000 8000 10000 12000 Load (N) LA36 24V motor speed vs. load LA36 24V motor current vs.
PAGE 4
LA36 Ordering example Econ: 3 6 0 0 1 0 0 0 A P 0 0 0 0 - 1 0 1 0 0 0 2 8 8 2 1 S 0 0 0 Not used Not used Safety factor: 0=2 Cable: 0 = None S = Straight Y = Y-Cable X = Special Plug Type: H = AMP J = Deutsch (DT) C = Flying leads X = Special Fire Category: 0 = None /HB 1 = V0 Install. Dim.
PAGE 5
LA36 Ordering example: 36 0 0 0 0 + 0 0 0 0 0 0 0 0 Cable: 0 = No cable 1 = 1,5 m power cable 2 = 5 m power cable 3 = 0,2 m power cable with AMP connector 4 = 1,5 m power and 1,5 signal 5 = 5 m power and 5 m signal 6 = 1,5 m Y-cable, power and signal in one 7 = 5 m power Cable + Data cable M12x1 (0367046-1500) (0367046-5000) (0367006) (0367046-1500+0367049-1500) (0367046-5000+0367049-5000) (0367020) (Bus) IP-degree: 2 = Standard (IP66) Motor type: A = 12 V DC with clutch B = 24 V DC with clutch
PAGE 6
LA36 Piston Rod Eye
PAGE 7
LA36 Back Fixture LA36 Back Fixture Orientation “0” Degrees “30” Degrees “60” Degrees “120” Degrees “150” Degrees “90” Degrees NB.
PAGE 8
LA36 built-in dimensions: When STROKE <300 = Built-in dimension: 200+STROKE LENGTH When STROKE >300 = Built-in dimension: 250+STROKE LENGTH I/O specifications: Power supply - Motor. Item Specification Comment Input voltage 12 VDC, ± 20% 24 VDC, ± 10% 36 VDC, ± 10% Cable dimension: 2 x 2.2 mm² (2 x AWG14) for all different voltages. Duty cycle 20% at max. load Ambient temperature 25˚ C Current consumption 2 - 23 Amp.
PAGE 9
Positioning feedback – Potentiometer. Item Specification Comment Potentiometer Bourns 0-10 K ohm A 5%, 10-Turn Type: 3540 Wirewound Output range with 8 mm spindle pitch 0 K ohm = 0 mm stroke 10 K ohm = 333 mm stroke The same for all LA36 8 mm models.e.g. 166.6 mm stroke = 5 Kohm. Output range with 12 mm spindle pitch 0 K ohm = 0 mm stroke 10 K ohm = 500 mm stroke The same for all LA36 12 mm models.e.g. 250 mm stroke = 5 Kohm.
PAGE 10
I/O Specifications: Analogue feedback. Item Specification Comment Description The actuator can be equipped with electronic circuit that gives an analog feedback signal when the actuator moves Input voltage 12 - 36 V DC Feedback circuit to be powered 1 second before motor runs, and until 1 second after the motor has stopped. Cable dimension 6 x 0,5 mm2 (6 x AWG20) Output voltage 0 -10 V (Option B) 0V = Fully retracted 10V = Fully extended +/- 0.
PAGE 11
I/O Specification: IC (Basic and Advanced) Item Specification Description Easy to use interface with integrated power electronics (H-bridge) for direct IC connection.
PAGE 12
Feedback: IC (Advanced). Item Specification Comment Feedback, PWM Frequency: Up to 200 Hz ± 5Hz Duty cycle: Any low/high combination between 0 and 100 percent Output voltage: (VIN - 1V) ± 1V Open Drain source current max. 12 mA Feedback, Hall Single Hall signal XOR: See fig. 1, page 9 Feedback, Voltage Any low/high voltage combination between 0 and 10 volts Ripple max. 200 mV Transaction delay max. 20 ms Linear feedback 0.
PAGE 13
Environmental test – Climatic Test Specification Comment TRD number Cold test EN60068-2-1 (Ab) Storage at low temperature: Temperature: -40°C Duration: 72h Not connected Tested at room temperature. TRD0509 EN60068-2-1 (Ad) Operating at low temperature: Temperature: -30°C Duration: 2h Actuator is not activated/connected Tested at low temperature. TRD0509 EN60068-2-2 (Bb) Storage at high temperature: Temperature: +90°C Duration: 72h Actuator is not activated/connected.
PAGE 14
Degrees of protection EN60529 – IP66 DIN40050 – IP69K IP6X - Dust: Dust-tight, No ingress of dust. Actuator is not activated. TRD0514 IPX6 – Water: Ingress of water in quantities causing harmful effects is not allowed. Duration: 100 litres pr. minute in 3 minutes Actuator is not activated. TRD0513 IPX6 –Connected actuator: Actuator is driving out and in for 3 min. 100(l/min) jet of water is placed at the wiper ring for 3 (min).
PAGE 15
Environmental test - Mechanical Test Specification Comment TRD number Free fall from all sides: Height of fall: 0.4 meter onto steel. Actuator not activated/connected. TRD0511 EN60068-2-36 (Fdb) Random vibration: Short time test:6.29g RMS Actuator is not connected Long time test: 7.21g RMS Actuator is not connected Duration: 2 hours in each direction TRD0502 EN 60068-2-6 (Fc) Sinus vibration: Frequency 5-25Hz: Amplitude = 3.
PAGE 16
Manual hand crank The manual hand crank can be used in the case of power failure. The cover over the Allen Key socket must be unscrewed before the Allen Key can be inserted and the Hand Crank operated. Hand Crank Torque: Max.16 Nm (at maximum load) Piston Rod movement per turn Gear A = 10.5 mm Gear B = 6.0 mm Gear C = 4.0 mm Gear F = 27 mm 6 mm Allen key Note: • The power supply has to be disconnected during manual operation.