TWINDRIVE ® TD3.2 / TD3.3 To learn more about LINAK please visit: W W W. L I N A K .
Contents Preface ................................................................................................................................................................. 4 Important information ....................................................................................................................................... 5 Safety instructions ..............................................................................................................................................
Preface We are delighted that you have chosen a product from LINAK A/S. LINAK systems are high-tech products based on many years of experience in the manufacture and development of actuators, electric control boxes, controls, and chargers. We are also constantly improving our products to meet customer requirements. This User Manual will tell you how to install, use, and maintain your LINAK TWINDRIVE® products. We are sure that the TWINDRIVE® products will give you many years of trouble-free operation.
Important information Important information on LINAK® products can be found under the following headings: Warning! Failure to comply with these instructions may result in accidents involving serious personal injury. Failing to follow these instructions can result in the product being damaged or being ruined. Safety instructions Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed.
(continued) During operation • Take care that the cables are not damaged or get jammed. • The products must only be used in an environment, which corresponds to their IP protection or where no IP protection is required. Repairs In order to avoid the risk of malfunction, all TWINDRIVE® repairs must only be carried out by authorised LINAK workshops or repairers, as special tools must be used and special gaskets must be fitted. TWINDRIVE under warranty must also be returned to authorised LINAK workshops.
Misc. on the TD3 TWINDRIVE® system This system is a TWINDRIVE system developed for leisure beds and for indoor use in private homes. Warranty There is 36 months’ warranty on the TWINDRIVE® products TD3 and HB20 against manufacturing faults calculated from the production date of the individual products (see label). LINAK A/S’ warranty is only valid in so far as the equipment has been used and maintained correctly and has not been tampered with.
Mounting guidelines for the TWINDRIVE® system Place the TD3 below the twist brackets/ “arms” of the bed Mount the TD3 and slide the closing devices over the gaps and make sure that the closing devices are in place before the TD3 is used.
Functional description Transmitter HB10: Up – down head motor Up – down foot motor Simultaneous up/down Transmitter HB20: Up – down head motor Up – down foot motor up to 3 extra channels common operation up/down (option) 1 2 Memory positions (3 positions) 3 S Store Button How to store • Drive to the desired position • Push “S” • Immediately afterwards the desired memory position must be pushed (1, 2 or 3) • The position is now stored Drive to stored memory position Push (1, 2 or 3) keep the button down
Handset for massage HB220G1+00003 (transmitter) Usage: Enter/exit massage command mode Sets the control in massage mode for controlling the massage functions (LED flashing) or returns to normal mode for controlling the bed adjustment (LED off). Pressing this key has no influence on the TWINDRIVE unit except from waking it up to make its response time to massage commands shorter. If no keys are pressed in 10 min. the control will automatically go to normal mode (LED off).
Starting a massage program always turns on both motors at current intensity. Short key press on right key turns off both massage motors no matter if it is running in a massage program, or separately. Keep key pressed to adjust the motor change speed up or down (left key down, right key up.) Store and recall massage settings. 2 massage settings can be stored. Adjust the massage to the preferred settings. Pres the “S” key followed by either key “1” or “2”.
Child lock To enable the function the position of the switch in the front of the transmitter must be changed. To unlock the handset press up and down keys of the 2nd row at the same time for one sec. When the blue LED turns on the handset is unlocked for 10 sec. after last key press. Then it automatically locks again. If the up + down key is pressed more than 2 sec. the handset will lock again.
Start-up - How to install RF handset: The TD3 can accept commands from up to 2 RF handsets. From the factory the TD3 cannot recognize any RF handsets at all and must be matched to the RF handset(s) by the end-user/bed manufacturer before these can control the TD3 operation.
Connections Ch.1 Ch.2 Ch.3 Mains inlet (HB connection) Battery cable/connection Battery drawer Reset Connection of massage motors: CH1 CH2 Footrest Headrest Connection of LA27 actuators: TD3 will default detect and run LA27 using plug and play rules illustrated in table below. Idea is Headrest is the first actuator then Footrest then Extra function. Headrest is always the one nearest Back-end and Footrest always the one nearest Leg-end.
Changing of batteries 1. Remove the battery cover (see Figure 1). 2. Use a blunt instrument to remove the battery. 3. Place 3 new batteries type R03 or LR03 (AAA) in the transmitter. Press a button for 3 sec. If above procedure not is performed the handset will function anyway after app. 5 minutes.
Disposal of batteries. "Details regarding safe disposal of used and leaking batteries: Batteries should be disposed in accordance with appropriate federal, state and local regulations. LINAK recommends that used or leaking batteries are disposed through the local recycling system. Please do not throw used or leaking batteries in normal household waste or in nature. This will cause damage to the enviroment. How to deal with leaking batteries. Leaking batteries should be disposed as described above.
Welding the twist bracket on the e frame 1) For the TD3 it is important that it is not welded on the outside of the twist bracket because there is not room for or g. a welding seam in the motor housing. Instead weld the bracket on the whole length of its ends. 2) To maintain the correct angle of rotation of the head rest and the foot rest it is important that the he twist bracket is welded according to o the below instructions.
Mounting instructions of the massage motor: Mounting on plate: Is mounted with 4 screws The massage unit is mounted with 4 x 4 mm round headed wood screws with flat underside. The head must be 8 mm in diameter and in length 19 mm + the thickness of the plate where the massage motor is mounted. Torque max. 2 Nm + resistance in the plate.
Mounted on one slat: The massage motor is mounted to the slat by using 2 brackets 0761009 and 4 x M6 screws of good quality. Inside the motor 4 self-locking nuts avoid the mounting screws to get loose.
Disposal of LINAK’s products As LINAK’s customers often ask us how our products can be disposed of or scrapped we have prepared this guidance that enables a classification to different waste fractions for recycling or combustion. Guidance We recommend to disassemble our product into as many fractions as possible at the disposal and try to make it recycable. As examples of main groups within waste fractions we can mention: Metal, plastic, cable shoe, combustible waste, and collection for recovery.
DRAWING APPENDIX TWINDRIVE® TD3 System: LA27 21
Massage motor MD1 HB10 Transmitter HB20 Transmitter 22
Manufacturer's declaration Implementation with regard to the Community legislation on machinery Directive 98/37/EC attachment II B: LINAK A/S, subsidiaries or representatives, (see back cover) prohibit that actuators are put into service until the machinery into which the actuator is to be incorporated has been declared in conformity with the provisions of all relevant Directives.
FACTORIES CHINA LINAK (Shenzhen) Actuator Systems, Ltd. Phone: +86 755 8610 6656 . Fax: +86 755 8610 6990 E-mail: sales@linak.cn . www.linak.cn NORWAY LINAK Norge AS Phone: +47 32 82 90 90 . Fax: +47 32 82 90 98 E-mail: info@linak.no . www.linak.no IRAN Bod Inc. Phone: +98 21 88527255 . Fax: +98 21 88514037 E-mail: mail@bod.ir . www.bod.ir DENMARK LINAK A/S . Group Headquarters Guderup Phone: +45 73 15 15 15 . Fax: +45 74 45 80 48 Fax (Sales): +45 73 15 16 13 E-mail: info@linak.com . www.linak.
