TWINDRIVE TD1 280 (Microprocessor) TM To learn more about LINAK please visit: W W W. L I N A K .
Contents Preface ................................................................................................................................................................. 4 Important information ....................................................................................................................................... 5 Safety instructions ..............................................................................................................................................
Preface We are delighted that you have chosen a product from LINAK A/S. LINAK systems are high-tech products based on many years of experience in the manufacture and development of actuators, electric control boxes, controls, and chargers. We are also constantly improving our products to meet customer requirements. This User Manual will tell you how to install, use, and maintain your LINAK TWINDRIVETM products. We are sure that the TWINDRIVETM products will give you many years of problem-free operation.
Important information Important information on LINAK® products can be found under the following headings: Warning! Failure to comply with these instructions may result in accidents involving serious personal injury. Failing to follow these instructions can result in the product being damaged or being ruined. Safety instructions Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed.
(continued) During operation • Take care that the cables are not damaged. • Unplug the mains cable on mobile equipment before it is moved. • The products must only be used in an environment, which corresponds to their IP protection. Repairs In order to avoid the risk of malfunction, all TWINDRIVETM repairs must only be carried out by authorised LINAK workshops or repairers, as special tools must be used and special gaskets must be fitted.
Misc. on the TWINDRIVETM TD1 280 system This system is a TWINDRIVE system developed for leisure beds and for indoor use in private homes. We advise children and disabled persons not to use the TD1 system without supervision. Warranty There is 36 months’ warranty on the TWINDRIVETM products TD1 and HB10/ HB20 against manufacturing faults calculated from the production date of the individual products (see label).
Description of the TWINDRIVETM TD1 280 system Each TWINDRIVETM TD1 unit consists of 1 - 2 internal motors and a built-in control box function which makes it a very compact unit. The mains cable is fixed. Only the handset and optional 1 - 2 external actuators must be connected. Application of the TWINDRIVETM TD1 280 system: Irrespective of the load the duty cycle 10% ~ 6 min./ hour or max. 2 min.
Mounting guidelines for the TWINDRIVETM 280 system for 2 x 9V batteries Connection for external actuators/massage device Handset socket Twist bracket Headrest Mains cable Closing device Footrest Figure 1 (Assembly overview) Mounting the handset Recommended usage of the strain relief the PCB. Otherwise the DIN-plug and print might be damaged when overstraining the cable.
Connection to the mains Please note that the TD1 must only be connected to the voltage stated on the label. IR system (infrared) Infrared system consist of 2 units. 1 receiver mounted as a standard handset with cable in the TD1 and a wireless unit. The wireless unit (Transmitter) is the actual handset. In cases where the Transmitter is damaged or has been lost is it possible to operate the TWINDRIVE system with the receiver.
Before start-up 1. Remove plastic strip Check that the transmission channel on the transmitter and the receiver is the same. If 2 beds are placed beside each other each bed must drive on their own channel to avoid undesirable drive. To ensure ooptimal functioning of the system the receiver must not be covered. Example of a good placement see page 19. RF System (Radio Frequency) RF system consist of 3 units. Receiver, cable and transmitter.
Start-up: The RFR box can accept commands from up to 2 RF handsets. From the factory the RFR box cannot recognize any RF handsets at all and must be matched to the RF handset(s) by the end-user/bed manufaccturer before these can control the TD operation. Activating the learning mode: • Activate the reset key on the RFR by using a pen or similar to keep the button pressed. • Keeping the reset key activated; the RF handset(s) must be activated one at a time by pressing a random key on the RF handset.
Initialisation of the TD1 memory system. To ensure optimum drive of the systems with memory, infrared and extra channels must be run out to the outward position and in again before use. This drive (out + in) must be done without stops.
Child lock (only by RF Handset) To enable the function the position of the switch in the front of the transmitter must be changed. To unlock the handset press up and down keys of the 2nd row at the same time for one sec. When the blue LED turns on the handset is unlocked for 10 sec. after last key press. Then it automatically locks again. If the up + down key is pressed more than 2 sec. the handset will lock again.
Handset for massage HB220G1+00003 (IR Transmitter) HB22RF2000 (RF Transmitter) Usage: Enter/exit massage command mode Sets the control in massage mode for controlling the massage functions (LED flashing) or returns to normal mode for controlling the bed adjustment (LED off). Pressing this key has no influence on the TWINDRIVE unit except from waking it up to make its response time to massage commands shorter. If no keys are pressed in 10 min. the control will automatically go to normal mode (LED off).
next program if a program is already activated. Starting a massage program always turns on both motors at current intensity. Short key press on right key turns off both massage motors no matter if it is running in a massage program, or separately. Keep key pressed to adjust the motor change speed up or down (left key down, right key up) Store and recall massage settings. 2 massage settings can be stored. Adjust the massage to the preferred settings. Press the “S” key followed by either key “1” or “2”.
Changing of the batteries (Transmitter) 1. Remove the battery cover (see Figure 1). 2. Use a blunt instrument to remove the battery. 3. Place 3 new batteries type R03 or LR03 (AAA) in the transmitter.
Exchange/connection of 9V batteries (Type 6F22 or 6LR61) 1. Remove the clamps from the battery (Figure 3). 2. Use a blunt instrument with a diameter of Ø6 mm to remove the battery (Figure 4). 3. Push the battery upwards via the two holes in the bottom of the unit (Figure 5). Figure 3 Figure 4 Figure 5 Disposal of batteries. "Details regarding safe disposal of used and leaking batteries: Batteries should be disposed in accordance with appropriate federal, state and local regulations.
Accessories and repair Ordering accessories Order from your nearest LINAK® dealer or subsidiary. Accessories Please contact your nearest LINAK dealer for information. Repairs Systems should only be repaired by an authorised LINAK service centre or engineer. Systems to be repaired under warranty must be sent to an authorised LINAK service centre. Warning! By unauthorised opening of the system there is a risk that it may malfunction at a later date.
Disposal of LINAK’s products As LINAK’s customers often ask us how our products can be disposed of or scrapped we have prepared this guidance that enables a classification to different waste fractions for recycling or combustion. Guidance We recommend to disassemble our product into as many fractions as possible at the disposal and try to make it recycable. As examples of main groups within waste fractions we can mention: Metal, plastic, cable shoe, combustible waste, and collection for recovery.
Mains cut-off The mains cut-off function disconnect the power to the TD1 system, if the system is not used. The mains cut-off is 100% maintance-free. The mains cut-off is available in 2 versions - an external version or an internal version. The external version is a small box placed on the plug of the mains cable. The internal version is integrated in the TD1 and thereby not visible. TD1 systems with internal mains cut-off are labelled TD1XXXXXXXXX2XX.
2) To maintain the correct angle of rotation of the headrest and the footrest it is important that the twist bracket is welded according to the above instructions. Non-complliance with the instructions could lead to a smaller angle of rotation or in a worst case damage to TD1. It is very important that the axle distance is kept. Example for correct welded twist bracket to the bedframe. 3) Before mounting, both mounting brackets must be pulled out to their outer position by pushing them back.
Mounting instructions of the massage motor: Mounting on plate: Is mounted with 4 screws The massage unit is mounted with 4 x 4 mm round headed wood screwx with flat underside. The head must be 8 mm in diameter and in length 19 mm + the thickness of the plate where the massage motor is mounted. Torque max. 2 Nm + resistance in the plate.
Mounted on one slat: The massage motor is mounted to the slat by using 2 brackets 0761009 and 4 x M6 screws of good quality. Inside the motor 4 self-locking nuts avoid the mounting screws to get loose.
Label for the TWINDRIVETM TD1 System Label for the LA27 Label for the LA31 Label for the Handset HB10: Label for the Handset HB20: Label for the Massage Motor 25
DRAWING APPENDIX TWINDRIVETM TD1 System: CH 1 HB20 Receiver 26 CH 2
HB20 Transmitter Massage motor MD1 RFR box 23 Reset 111 44 27
LA27 47 LA31 INSTALLATIONDIM.=STROKE + ADDITION . LINAK A/S LA31002C 152.75 78 27.5 62.9 153 163 7.4 23.5 80.
Manufacturer's declaration Implementation with regard to the Community legislation on machinery Directive 98/37/EC attachment II B: LINAK A/S, subsidiaries or representatives, (see back cover) prohibit that actuators are put into service until the machinery into which the actuator is to be incorporated has been declared in conformity with the provisions of all relevant Directives.
FACTORIES CHINA LINAK (Shenzhen) Actuator Systems, Ltd. Phone: +86 755 8610 6656 . Fax: +86 755 8610 6990 E-mail: sales@linak.cn . www.linak.cn NORWAY LINAK Norge AS Phone: +47 32 82 90 90 . Fax: +47 32 82 90 98 E-mail: info@linak.no . www.linak.no IRAN Bod Inc. Phone: +98 21 88527255 . Fax: +98 21 88514037 E-mail: mail@bod.ir . www.bod.ir DENMARK LINAK A/S . Group Headquarters Guderup Phone: +45 73 15 15 15 . Fax: +45 74 45 80 48 Fax (Sales): +45 73 15 16 13 E-mail: info@linak.com . www.linak.
