TOPCAT Classroom Audio System User Manual
TABLE OF CONTENTS SECTION 1: Overview 4 6 7 9 10 11 12 13 Important Safety Instructions System Components and Unpacking Optional Components Side Panel Controls and Connections Media Connector Front Panel Controls Media Connector Rear Panel Controls REDMIKE VC Controls and Connections Cradle Charger Controls and Connections SECTION 2: Installation 14 15 17 Installation Planning Supply Power to the Selected Location Step 1. Select Mounting Location 18 Step 2.
TABLE OF CONTENTS CONT’D SECTION 4: Troubleshooting 40 41 Troubleshooting Guide Remove and Replace Amplifier Module SECTION 5: Warranty & Specifications 44 45 46 Warranty, Safety & Specifications Safety Warnings and Certifications System Specifications
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use the apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. 9. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
IMPORTANT SAFETY INSTRUCTIONS CONT’D To avoid potential equipment damage and/or serious injury, READ AND FOLLOW all safety precautions when installing the TOPCAT. WARNINGS are coated throughout the procedural steps in this guide, and are repeated below for emphasis. UÊ USE A CERTIFIED ELECTRICIAN FOR POWER CONNECTIONS. The TOPCAT system uses standard 100 – 240VAC power. Obtain the services of a certified electrician when supplying and connecting power to the Ceiling Enclosure.
5. Warranty, Safety & Specifications OVERVIEW SYSTEM COMPONENTS AND UNPACKING The standard configuration of the TOPCAT® will contain: 3. Optional Accessories 4. Troubleshooting SECTION 1: 1. Overview 2.
USB Cable Screws and Anchors for optional wall mounting OPTIONAL COMPONENTS 5. Warranty, Safety & Specifications 4. Troubleshooting 3. Optional Accessories Audio Cable Kit 2. Installation CONT’D 1.
5. Warranty, Safety & Specifications 4. Troubleshooting 3. Optional Accessories SYSTEM COMPONENTS Equipment which may be part of your TOPCAT: Standard Accessories TRX-TC PS-24V-2.5 RMV BA-NH2A27 AC-RMLC2 BC-RMCC PS-5V-1.0 TRX-MC CA-USBAM CA-MSC3535 CA-AD-RCA2-35 TOPCAT all-in-one ceiling mount system 24V/2.5A power supply for TOPCAT REDMIKE VC microphone with battery AA NiMH rechargeable sensing battery for REDMIKE REDMIKE lavaliere cord REDMIKE cradle charger 5V/1.
INSTALLATION INSTALLATION PLANNING Before beginning installation, make sure you have the necessary tools and materials on hand and that pre-installation site preparation has been accomplished. 4. Troubleshooting 5. Warranty, Safety & Specifications SECTION 2: TOOLS & MATERIALS 3. Optional Accessories In addition to the contents of the TOPCAT system, you will need the following tools & materials: UÊ Flat Blade screwdriver (small) UÊ Pliers UÊ Wire cutters 2.
5. Warranty, Safety & Specifications 4. Troubleshooting 1. SELECT MOUNTING LOCATION The TOPCAT is shipped ready to mount in a standard suspended ceiling grid. All mounting hardware need to secure the TOPCAT in the ceiling is provided except for that needed to wire the AC power to the chassis. TOPCAT will distribute sound throughout a classroom of up to 1600 square feet. The location of TOPCAT is critical to ensure even sound distribution. 1.
1. If the ceiling tile that was removed is 2’ x 4’, it needs to be cut in half to accommodate the TOPCAT. If the ceiling tile that was removed is 2’ x 2’, no cutting of the tile is necessary. 2. Set the ceiling tile on a flat work surface with the patterned side facing down. 5. Warranty, Safety & Specifications The dimensions of the TOPCAT speaker are 595mm x 595mm and is designed to lie onto any standard suspended ceiling tile grid.
5. Warranty, Safety & Specifications 3. SECURING THE TOPCAT To comply with Building Codes, the TOPCAT MUST be fastened to the ceiling grid and secured with a safety wire. 4. Troubleshooting 1. Locate the four (4) self-drilling sheet metal screws. 2. Utilizing existing center holes on the vertical section of the ceiling grid, drill one screw per side on opposite sides of the TOPCAT (see figure 4). 3. Locate the 15ft length of safety wire and the eye screw.
SUPPLY POWER TO THE SELECTED LOCATION WARNING! USE A CERTIFIED ELECTRICIAN FOR POWER CONNECTIONS. The TOPCAT System uses standard 100 – 240VAC power. Obtain the services of a certified electrician when supplying and connecting power to the TOPCAT chassis. Be sure electrical installation complies with local building codes. Improperly installing and /or connecting power to the system may result in Equipment Damage, serious injury and/or Death.
5. Warranty, Safety & Specifications 4. Troubleshooting ALTERNATE POWER (OPTIONAL) When electrical AC power is not available above the ceiling for installation with the TOPCAT, there is an alternative method for supplying power to the TOPCAT. Note: There are two DC Power Connectors for connecting power to the TOPCAT. Both connectors perform the same function. Use the internal DC Power Connector located on the amplifier card when AC power is connected directly to the TOPCAT.
Choose a location for the Media Connector module that is convenient to the classroom audio sources and power supply. 5. Warranty, Safety & Specifications 5. LOCATION OF THE MEDIA CONNECTOR NOTE: The MC does not require a direct line of sight to the TOPCAT. However it functions best when no obstructions are between the two devices. Do not place in an enclosed metal cabinet. COUNTER OR DESKTOP 4. Troubleshooting The MC can be placed on a counter or wall mounted. Determine the best location for your room.
5. Warranty, Safety & Specifications 6. CONNECTING THE POWER SUPPLY The Media Connector (MC) can be powered in either of two ways: Ê UÊ Ê«ÜiÀÊvÀÊ>Êi>ÀLÞÊiiVÌÀV>ÊÕÌiÌ 3. Optional Accessories 4. Troubleshooting Ê UÊ 1- Ê«ÜiÀÊvÀÊ>ÊV«ÕÌiÀ Use whichever power source is most convenient to the location of the MC. AC Power 1. Locate the DC port at the rear of the MC. 2. Place the DC end of power cord into DC port at the rear of the MC. 3. Place the AC end of power cord into an electrical outlet.
4. Troubleshooting The Media Connector is designed to integrate multiple audio sources quickly and easily. 5. Warranty, Safety & Specifications 7. AUDIO INTEGRATION 2. Installation 3. Optional Accessories TopCAT 1.0A USB POWER AUDIO 2 AUDIO 3 AUDIO 4 AUDIO IN VOLUME 1.
5. Warranty, Safety & Specifications 4. Troubleshooting 3. Optional Accessories 8. VOLUME ADJUSTMENT FOR THE MEDIA CONNECTOR The Media Connector can be used as the primary volume control for the audio sources you’ve connected. 1. Connect the audio source(s) to the Media Connector using the 3.5mm cables provided 2. Set the audio source volume to provide sound through the TOPCAT AUDIO 1 5V 1.0A Audio Input AUDIO AUDIO 2 3 AUDIO 4 AUDIO VOLUME USB POWER 3.
Use the following table to determine if your TOPCAT and Media Connector are registered. MC Power MC LINK LED Status OFF All LEDs Off Turn MC Power ON Blue LED is LIT ON Blinking Green Not Linked - Needs to be registered ON Continuous Green Linked to TOPCAT 5. Warranty, Safety & Specifications 4. Troubleshooting The TOPCAT and Media Connector must be registered or synchronized with each other before they will operated together. (These modules come preregistered from the factory.
5. Warranty, Safety & Specifications 4. Troubleshooting 3. Optional Accessories 2. Installation 1. Overview 10. SETUP AND OPERATION OF THE REDMIKE VC AND TOPCAT Once the REDMIKE is charged, follow these steps to set it up for use. NOTE: This procedure is easier with two people. 1. Turn the TOPCAT power on. The blue LED on the Media Connector will glow. 2. Remove the REDMIKE VC from the charging cradle and turn it on. 3.
5. Warranty, Safety & Specifications UÊÊ -«i>ÊÊ>Ê>ÌÕÀ>ÊÛVi°Ê ÊÀ>Ê conversational speech level will provide an adequate signal. It is not necessary to increase the intensity of your voice—the audio system provides adequate amplification (approximately 5 – 10 dB) above ambient room noises. 4. Troubleshooting TIPS TO OBTAIN OPTIMUM AUDIO PERFORMANCE 2.
5. Warranty, Safety & Specifications 4. Troubleshooting 3. Optional Accessories Before use, the REDMIKE VC should be charged. It will take 8-9 hours for the REDMIKE VC to obtain a full charge. A fully charged REDMIKE VC will last for over 7 hours of use. If microphones are used daily, they should be kept in the cradle – microphones can be left in a charging cradle constantly for up to 2 weeks without causing degradation to battery life.
SIDE VIEW 3. Optional Accessories 2. CH B VOLUME: Controls the volume level for microphone set to channel B. Turn clockwise to increase volume or counter clockwise to decrease volume. 4. Troubleshooting 1. CH A VOLUME: Controls the volume level for microphone set to channel A. It is preset at the factory to its 12 O’clock position. Turn clockwise to increase volume or counter clockwise to decrease volume. 5. Warranty, Safety & Specifications SIDE PANEL CONTROLS AND CONNECTIONS 2. Installation 3.
5. Warranty, Safety & Specifications 4. Troubleshooting MEDIA CONNECTOR FRONT PANEL CONTROLS AUDIO 1 1 1.0A 2 2 3 1. Overview 1. POWER CABLE INPUT: When using an AC outlet, plug the power supply (5V/1.0A) in to this jack. 2. USB POWER INPUT: Alternatively, use the provided USB cable to power the Media Connector from a USB-enabled computer. 3. FOUR AUDIO INPUTS: Connect standard audio devices to any of the 3.5mm stereo inputs.
3. Optional Accessories 4. Troubleshooting 5. Warranty, Safety & Specifications MEDIA CONNECTOR REAR PANEL CONTROLS 1. SYSTEM POWER SWITCH: System power is turned ON or OFF with this pushbutton. When power is ON, the blue power LED lights. 2. REGISTRATION PUSHBUTTON: Pushing the Registration button in conjunction with the registration button on the TOPCAT module will cause the two modules to synchronize as an operating system. Refer to the Registration Procedure in this manual. UT 3 4 3.
1 4 Slide battery door o p Remove tab before en us e 5. Warranty, Safety & Specifications 4. Troubleshooting REDMIKE VC (Volume Control) CONTROLS AND CONNECTIONS 5 3. Optional Accessories 6 2 7 2. Installation 3 1. Overview 8 1. POWER /MUTE BUTTON 2. POWER/LOW BATTERY INDICATOR: A BLUE light indicates the REDMIKE VC is on and fully charged. A RED light indicates a charge is needed. 3. BATTERY COMPARTMENT: To open, slide the door downward.
2 3 1. CHARGE INDICATORS: The light glows RED while the REDMIKE is charging. When fully charged, the light will glow GREEN. A blinking RED light indicates that no battery is sensed, (REDMIKE Yellow Protective Tab may not have been completely removed—see page 5, item 4.) A blinking Green LED means a non- Lightspeed battery has been installed (possibly an alkaline battery). 2. DC POWER PORT: Connect the DC power cord here. 1. Overview 1 2. Installation 3. Optional Accessories 4. Troubleshooting 5.
5. Warranty, Safety & Specifications OPTIONAL ACCESSORIES REDMIKE SHARE: CONTROLS AND CONNECTIONS 3. Optional Accessories 4. Troubleshooting SECTION 3: 3 2. Installation 2 4 1. Overview 1 5 1. POWER SWITCH: 2. POWER/CHARGE INDICATOR: this light glows blue when turned on and turns off to indicate low battery level. When charging, the light glows red. 3.
4. The LED on the microphone will glow RED to indicate charging. 5. Leave the REDMIKE Share plugged in overnight (8-10 hours) to obtain a full charge. 1. Overview 2. Installation 2. Make sure the cradle charger is plugged into a wall outlet. Connect one end of the charging cable into the jack labeled CHARGER on the bottom of the REDMIKE Share. 3. Plug the other end into the charging jack on the rear of the cradle charger. 3. Optional Accessories 1. Ensure that the REDMIKE Share is turned OFF. 5.
5. Warranty, Safety & Specifications 4. Troubleshooting 3. Optional Accessories 2. Installation REDMIKE SHARE: INITIAL SET-UP 1. Ensure the TOPCAT is ON. The blue LED on the Media Connector will glow. 2. Turn on the REDMIKE Share by sliding the switch to the top position. 3. Grip the barrel in the center section. Avoid covering the infrared emitters just below the microphone grille. This could interrupt signal transmission. 4. While speaking in a normal voice, increase the CH.
The REDMIKE includes a 3.5mm audio input jack to connect to an audio source like a laptop or MP3 player. The REDMIKE VC will transmit the audio signal to be played through the system. If your system includes two REDMIKE VCs, we recommend using Channel B (student mike) to amplify the external audio equipment so the teacher’s volume on the Channel A (teacher mike) does not have to be adjusted. 4. Troubleshooting 5.
5. Warranty, Safety & Specifications 4. Troubleshooting 1. Turn the ALD (Assistive Listening Device) volume control on the Media Connector front panel all way the down. of the Media Connector. 2. Determine the size and type of audio input jack on the device as many manufacturers’ products differ in connector size and shape. The Lightspeed LES-370 Personal FM System requires a 3.5mm to 3.5mm patch cable (part# CAMMC3535, not included). 3.
Best placement 1. Overview Avoid! 2. Installation 3. Optional Accessories Good placement 5. Warranty, Safety & Specifications Sometimes having the Integrated Sensor Receiver (ISR) mounted on the TOPCAT in the center of the room is not the ideal location. A poor location will cause substandard performance of the Classroom Audio System. The ISR should be as high as possible in the room – the ceiling is the best location, centered along the longest wall in the room.
5. Warranty, Safety & Specifications 4. Troubleshooting IR SENSOR/RECEIVER (ISR) INSTALLATION CONT’D ISR Removal from TOPCAT The system ISR is shipped mounted to the TOPCAT front panel. For most installations, it will not need to be moved. However, there are some room situations where the center of the classroom is not the best location and needs to be removed from the TOPCAT and installed else where in the classroom. Grasp the ISR on its two sides and pull.
3. Remove Pin From ISR Install the blank cover plate (provided with the TOPCAT) by snapping into place where the ISR was located. 1. Overview 4. Place Cover Plate Over ISR Opening 2. Installation 3. Optional Accessories Turn the ISR over and remove the ISR Clip from the ISR (release the spring latch and slide it out). 5. Warranty, Safety & Specifications CONT’D 4.
5. Warranty, Safety & Specifications 4. Troubleshooting 3. Optional Accessories 2. Installation IR SENSOR/RECEIVER (ISR) INSTALLATION CONT’D Suspended Ceiling Mount 1. Attach the bracket to the ceiling tile grid (t-bar). a. Slide the tabs onto the outsides of the t-bar, starting with one corner. b. Attach the second tab around the other side of the t-bar. c. Repeat with the other side of the bracket so it is connected at all four points. clip connects to t-bar on ceiling 2.
3. Uncoil the Cat 5 sensor cable. Connect one end of the cable to the ISR. Secure wire overhead and route it back to the TOPCAT system, making sure to follow all local codes. 4. Insert the CAT 5 cable into the TOPCAT chassis through the 1 inch diameter hole provided. 5. Open the TOPCAT front panel door. Find where the previous CAT 5 cable was connected and plug in the new CAT 5 cable. 6.
5. Warranty, Safety & Specifications 4. Troubleshooting 3. Optional Accessories IR SENSOR/RECEIVER (ISR) INSTALLATION CONT’D Wall/Solid Ceiling Mount 1. Screw the bracket to a place high on the wall or in the middle of the solid ceiling. Mount the bracket horizontally as shown above. 5. Open the TOPCAT front panel door. Find where the previous CAT 5 cable was connected and plug in the new CAT 5 cable. 2. Uncoil the Cat 5 sensor cable. Connect one end of the cable to the ISR.
COMMON PROBLEMS AND SOLUTIONS Note: Most problems are directly related to low battery power. Please run through the “Battery Check” items first. For remaining troubleshooting, use known good, fully-charged batteries. UÊ SOLUTION: Battery Check wÀÊÌ iÊ*ÜiÀÊ ÊÃÊLÕi° UÊ wÀÊL>ÌÌiÀiÃÊ>ÀiÊV >À}i`Ê each night. UÊ wÀÊ«À«iÀÊL>ÌÌiÀiÃÊ>ÀiÊ used. The REDMIKE VC requires the Lightspeed BA-NH2A27 rechargeable sensing battery for proper charging.
5. Warranty, Safety & Specifications 4. Troubleshooting REMOVE AND REPLACE AMPLIFIER MODULE Troubleshooting TOPCAT may require the amplifier module to be replaced. Troubleshooting and repair can be accomplished without requiring the service of an electrician as long as the TOPCAT chassis is not removed from the ceiling. Once replaced, the amplifier will need to be registered with the Media Connector Module and the microphone channel A and channel B will need to be setup with the classroom microphone(s).
4. Unplug the following cables from the amplifier module 2. Installation Remove Screws 3. Optional Accessories 4. Troubleshooting Loosen the screws holding the Amplifier to the chassis. See Figure a. Cone Speaker b. Flat panel speaker 1. Overview 3. 5. Warranty, Safety & Specifications REMOVAL AND REPLACE AMPLIFIER MODULE CONT’D c.
5. Remove the Amplifier module 6. To install the new amplifier module, perform this procedure in reverse order. 7. Registering the TOPCAT with the Media Connector Module perform the TOPCAT AND MEDIA CONNECTOR REGISTRATION procedure in this manual. 8. To adjust the optimum microphone volume level, perform the SETUP AND OPERATION OF THE REDMIKE VC procedure in this manual 1. Overview 2. Installation 3. Optional Accessories 4. Troubleshooting 5.
Lightspeed Classroom Audio Systems are guaranteed against malfunction due to defects in materials and workmanship for a period of FIVE (5) YEARS, beginning at the date of the purchase invoice. If such malfunction occurs, the product will be repaired or replaced (at Lightspeed’s option) without charge during the warranty period. Lightspeed’s Warranty Exchange Program applies to all infrared systems within the five (5) year warranty period.
5. Warranty, Safety & Specifications SAFETY WARNINGS AND CERTIFICATIONS 4. Troubleshooting ! 3. Optional Accessories USE A LIGHTSPEED SUPPLIED BATTERY ONLY CERTIFICATIONS 1. Overview 2. Installation This product is listed to UL standards and requirements for electrical safety by Underwriters Laboratories Inc. This product conforms with the essential requirements of the following European Union Directives: 89/336/EEC, 92/31/EEC, 93/68/ EED, and 2004/108/EC Electromagnetic Compatibility Directives.
5. Warranty, Safety & Specifications 4. Troubleshooting 3. Optional Accessories SAFETY WARNINGS AND CERTIFICATIONS This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Panel Size Frequency Response Impedance Power Handling Power Enclosure Weight RECEIVER/TRANSMITTER SPECIFICATIONS Media Connector Module Frequency Response Signal-to-noise Ratio Audio Distortion Audio Inputs Audio Outputs DC Power Input USB Power Mounting Dimensions (L x W x H) 80 Hz to 10 kHz ±3 dB >70 dB <1% Four (4) 3.5mm stereo jack One 3.5mm stereo jack with volume control 5 V / 1.0 Amp, 0.65mm coaxial barrel DC power jack 5 V mini-B USB connector wall or table-top 5.75” x 8.75” x 10” / 146mm x 222.
5. Warranty, Safety & Specifications 4. Troubleshooting 3. Optional Accessories 2. Installation 1. Overview 46 SYSTEM SPECIFICATIONS CONT’D INFRARED SENSOR INTEGRATED SENSOR / RECEIVER (ISR) Power Reception Coverage Mounting Receiving Diodes From TOPCAT Rooms up to 1600 sq ft / 150 m2 (ceiling 12ft / 3.
50 1. Overview 2. Installation 3. Optional Accessories 4. Troubleshooting 5.
Heed all warnings. 4. Follow all instructions. 5. Do not use the apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. 9. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug.
5. Warranty, Safety & Specifications 4. Troubleshooting 3. Optional Accessories 2. Installation 1. Overview 52 IMPORTANT SAFETY INSTRUCTIONS CONT’D To avoid potential equipment damage and/or serious injury, READ AND FOLLOW all safety precautions when installing the TOPCAT. WARNINGS are coated throughout the procedural steps in this guide, and are repeated below for emphasis. CAUTION UÊ USE A CERTIFIED ELECTRICIAN FOR POWER CONNECTIONS. The TOPCAT system uses standard 100 – 240VAC power.
SYSTEM COMPONENTS AND UNPACKING 3. Optional Accessories The standard configuration of the TOPCAT® will contain: 5. Warranty, Safety & Specifications OVERVIEW 4. Troubleshooting SECTION 1: Media Connector Module 1. Overview 2.
5. Warranty, Safety & Specifications 4. Troubleshooting 3. Optional Accessories 2. Installation 1.
Standard Accessories TRX-TC PS-24V-2.5 RMV BA-NH2A27 AC-RMLC2 BC-RMCC PS-5V-1.0 TRX-MC CA-USBAM CA-MSC3535 CA-AD-RCA2-35 TOPCAT all-in-one ceiling mount system 24V/2.5A power supply for TOPCAT REDMIKE VC microphone with battery AA NiMH rechargeable sensing battery for REDMIKE REDMIKE lavaliere cord REDMIKE cradle charger 5V/1.0A power supply Transmitter-Receiver Media Connector Module USB cable (type A-MINI-B) Patch cables 3.5mm to 3.5mm short length Dual RCA jack – 3.5mm stereo plug adapter 5.
5. Warranty, Safety & Specifications 4. Troubleshooting SECTION 2: INSTALLATION INSTALLATION PLANNING Before beginning installation, make sure you have the necessary tools and materials on hand and that pre-installation site preparation has been accomplished. 3. Optional Accessories TOOLS & MATERIALS In addition to the contents of the TOPCAT system, you will need the following tools & materials: UÊ Flat Blade screwdriver (small) UÊ Pliers 2.
TOPCAT will distribute sound throughout a classroom of up to 1600 square feet. The location of TOPCAT is critical to ensure even sound distribution. 1. Identify the center of the listening area of the classroom for optimum location. See Figure 1. 2. Select a ceiling tile that is free of fixtures (lighting, HVAC, etc.) nearest to the center point. 5. Warranty, Safety & Specifications The TOPCAT is shipped ready to mount in a standard suspended ceiling grid.
5. Warranty, Safety & Specifications 4. Troubleshooting 2. INSTALLING THE TOPCAT INTO THE CEILING GRID The dimensions of the TOPCAT speaker are 595mm x 595mm and is designed to lie onto any standard suspended ceiling tile grid. Spacers are attached to center the TOPCAT in a 2’ x 2’ or 2’ x 4’ ceiling grid. (Remove these spacers when installing into a 600 x 600 mm grid.) 1. If the ceiling tile that was removed is 2’ x 4’, it needs to be cut in half to accommodate the TOPCAT.
To comply with Building Codes, the TOPCAT MUST be fastened to the ceiling grid and secured with a safety wire. Follow all local and state laws. 5. Warranty, Safety & Specifications 3. SECURING THE TOPCAT 2. Utilizing existing center holes on the vertical section of the ceiling grid, drill one screw per side on opposite sides of the TOPCAT (see figure 4). 3. Locate the 15ft length of safety wire and the eye screw. The safety wire needs to be permanently attached to the solid structural ceiling above. 4.
5. Warranty, Safety & Specifications 4. Troubleshooting 3. Optional Accessories 4. INSTALLING AND WIRING ELECTRICAL POWER There are two methods of providing power for the TOPCAT. 1. New Construction Installations: Connect directly to the buildings mains AC power. 2. Retrofit situations: Can either wire to the building mains or order the optional power extension cable (DCPEX-NA). SUPPLY POWER TO THE SELECTED LOCATION WARNING! USE A CERTIFIED ELECTRICIAN FOR POWER CONNECTIONS.
Note: There are two DC Power Connectors for connecting power to the TOPCAT. Both connectors perform the same function. Use the internal DC Power Connector located on the amplifier card when AC power is connected directly to the TOPCAT. Use the connector access located on the outside of the TOPCAT when using the optional power extender cable. 5.
62 1. Overview 2. Installation 3. Optional Accessories 4. Troubleshooting 5.
63 1. Overview 2. Installation 3. Optional Accessories 4. Troubleshooting 5.
L I G HTSP E E D TE C H NOL O G I ES 1 1 5 0 9 SW HE R M A N R O A D / T U AL AT I N , OR 97062 TO L L FR E E : 8 0 0 .7 3 2 .8 9 9 9 / P H ON E: 503. 684. 5538 / FAX : 503. 684. 3197 L IG HTSPE E D - TE K.