Classroom Audio System 1 POWER 2 1 Tea 2 ch er 2 1 cher Tea UT INP 1 2 Teacher VOL INPUT lightspeed-tek.com 800.732.
SECTION 1: OVERVIEW SYSTEM COMPONENTS AND UNPACKING The standard configuration of the Redcat® Access will contain: 1 POWER 2 1 Tea 2 ch er 2 r 1 che a Te T PU IN Redcat® Access Receiver/Amplifier with Table Stand and Power Supply 1 2 Teacher Flexmike® Classroom Microphone Wall Charger & Charging Cables VOL INPUT
FRONT PANEL INDICATORS 1. POWER ON INDICATOR: The power LED will glow blue when power is applied. 2. MIC 1 & MIC 2: Mic link and registration indicators a. Flashing amber indicates registration is in process. b. Solid green indicates a link has been established. 2 2 1 1 POWER 2 TOP PANEL CONTROLS AND CONNECTIONS 1. MIC VOLUME: Controls the volume level of the microphones. 2. TONE CONTROL: Adjusts the audio level for optimum sound quality.
SIDE PANEL CONTROLS AND CONNECTIONS 1. REGISTRATION: Press this button if there is a new microphone to be registered. 1 REGISTER 2. AUDIO INPUT VOLUME CONTROL & INPUT JACK: 3.5mm stereo connector for connecting classroom audio sources to the Redcat Access (RCA). Controls the volume level of the audio input from the connected audio source.. AUDIO IN MIN 2 MAX AUDIO (ALD) OUT MIN 3 MAX 3. AUDIO OUTPUT VOLUME CONTROL & OUTPUT JACK: 3.
FLEXMIKE CONTROLS AND CONNECTIONS 2 1 3 4 5 8 1 Tea 2 ch er 6 2 r 1 che a Te 1 Tea 2 ch er T PU IN 7 9 10 lightspeed-tek.com 800.732.8999 1 2 Teacher 1. POWER/MUTE SWITCH: press and hold to power on, press to mute, press and hold to power off. 2. MIC 1 STATUS: lighted to indicate microphone is registered as MIC 1 VOL 1 2 Teacher INPUT • Blue: solid = normal operation; flashing = linking in process • Red: solid = muted; flashing = muted while linking in process 3.
SECTION 2: SET-UP & USE 1. DETERMINE SET-UP LOCATION The Redcat Access is shipped with a table stand connected and ready for use. Alternatively, the table stand can be used as the wall mount bracket. Advantages of either include: Tabletop (recommended): Wall-mount: • Virtually no setup time • More permanent setup • Greater flexibility to move to different locations • Greater security 1A.
1B. TO SET-UP MOUNTED ON A WALL First, consider that the RCA should be placed within 7 feet of an electrical outlet and about 6-8 feet off the ground. Next, find a location as far away as possible from the teacher who will be using the mic. The best place is centered on the long wall opposite the teacher. If this is not possible, other good locations are on the wall next to the teacher. Avoid placing the RCA on any wall close to where the teacher usually stands to instruct the class.
1B. TO SET-UP MOUNTED ON A WALL CONT’D 1. Level template and tape to wall 2. Mark position of drill holes on wall 3. Drill pilot holes 4. Insert anchors 5. Insert screws through the RCA feet into the anchors 6. If using optional security bracket, mount on wall using the provided screws and anchors 7.
4. CHARGING THE FLEXMIKE Before use, the Flexmike should be charged. It will take 8-9 hours for the Flexmike to obtain a full charge. A fully charged Flexmike will last for up to 8 hours of use. If microphones are used daily, they should be charged each night – microphones can be left charging constantly for up to 2 weeks without causing degradation to battery life. When plugged into a charger, a red light on the Flexmike indicates the battery pack is charging.
5. OPERATING THE FLEXMIKE Once the Flexmike is charged, follow these steps to set it up for use. 1. Turn the Redcat Access power switch to the on position. 2. Remove the Flexmike from the charging cable and put it on by connecting the magnetic clasps behing your neck. The Flexmike will automatically power on when it is left in the on position while charging. 3. The microphone volume on the Flexmike is set at the factory to the mid point. 4. While speaking in a normal voice, fine-tune the volume up or down.
OUTPUT TO ASSISTIVE LISTENING DEVICE (ALD) 1. Turn the ALD (Assistive Listening Device) volume control on the Redcat Access side panel all way the down. 2. Determine the size and type of audio input jack on the device as many manufacturers’ products differ in connector size and shape. The Lightspeed 370 Transmitter requires a 3.5mm to 3.5mm patch cable (part# MMC3535, not included). 3. Connect a patch cable from the ALD’s microphone jack or AUX input to the 3.
SECTION 4: TROUBLESHOOTING COMMON PROBLEMS AND SOLUTIONS Note: Most problems are directly related to low battery power. Please run through the “Battery Check” items first. For remaining troubleshooting, use known good, fully-charged batteries. ALL PROBLEMS: Most Problems are related to low battery power. SOLUTION: Battery Check • Confirm batteries are charged each night. • Confirm proper batteries are used. The Flexmike requires the Lightspeed NH2.4 rechargeable sensing battery pack for proper charging.
TIPS TO OBTAIN OPTIMUM AUDIO PERFORMANCE • Speak in a natural voice. A normal conversational speech level will provide an adequate signal. It is not necessary to increase the intensity of your voice—the audio system provides adequate amplification (approximately 5 – 10 dB) above ambient room noises. • Avoid wearing jewelry that may rub or bump against the microphone. • Mute the Flexmike during private conversations with a student, parent, or other classroom visitor.
FCC Notice to user This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Canada Notice to user English This device complies with Industry Canada licence‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. French Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
NOTICE FOR USB NOTE: Lightspeed is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.