For Models: LS-101B-WLVCTL (Controller) LS-201-WMSR-SPL (Motion Sensor + Spotlight) Controller Motion Sensor & Spotlight Installation and Use
Contents The Novolink Lightscape System 2 What’s Included 4 Download the App 6 Tools You’ll Need 9 Controller Installation 11 Motion Sensor Installation 25 Spotlight Installation 31 Online Resources & Help 41
The Lightscape System Side Yard On : 5:3 0 pm 1:0 0 am Zone 2 Zone 1 Novolink Lightscape Landscape Lighting System gives you simple, convenient, and wireless control of your hard-wired, low-voltage landscape lighting environment. With the Controller in place, use our handy Novolink Lightscape App to schedule when lights will turn on and when they’ll turn off, whether at a specific time, or at dusk and dawn. Our Controller’s unique connector is the key.
What’s Included Novolink Lightscape Controller 1 Q ui ck St ar t G ui de Motion Sensor & Spotlight 1 3 5 5 Q ui ck St ar t G ui de 2 2 3 4 4 4 1 2 3 4 5 antenna main body connector stake quick star t guide 6 1 2 3 4 5 6 motion sensor sensor wall mount spotlight stake spotlight wall mount quick star t guide 5
Download the Novolink Lightscape App 1. Before you install any Novolink Lightscape components, download the app from Google Play (Android) or from the App Store (iOS). SC AN T HIS CO D E TO D OW NLOAD T HE APP The app requires a device with Bluetooth® wireless capability. 2. Make sure your device’s Bluetooth is ON. You may find this in your device set tings. 3. Open the app, and follow the prompts to activate a component (like the Controller). Note: you can activate more than one component at one time.
Tools You’ll Need 2 3 4 6 7 D 5 AA 1 1 protective eyewear 2 wire stripper / cut ter (18 to 12 gauge wire) 3 drill 4 philips screwdriver 5 pump pliers (optional) 6 for spotlight: (4) D alkaline bat teries 7 for motion sensor: (3) AA alkaline bat teries 9
Controller Installation 11
Before You Start low-voltage transformer To install the Controller, you’ll need access to the low-voltage wire that runs between the Low-Voltage Transformer and the first of your landscape lights. This may require exposing the wire(s) if they’re buried. Make sure your Transformer will work optimally with the Novolink Lightscape system on our website: https://www.novolinkinc.
Assembly 2 keep the short length of this wire in mind when planning where to install the Controller. 1. Make sure you have all par ts of the Controller. Check the mechanisms and wiring for damage. Set the par ts on a clean, sturdy work-sur face. 2. At tach the antenna top to the main Controller body. 3. Then at tach the stake to the main Controller body. Twist until it ’s firmly in place.
Install the Connector 1. Unplug / disconnect your Low-Voltage Transformer We recommend that you turn OFF power at the circuit breaker or fuse, and test that the power is OFF before proceeding. 3. Unear th this por tion of the low-voltage wire. Make sure there’s enough slack to easily cut and manipulate the wire. Then use wire-cut ters to cut the wire here. 2. Locate the low-voltage wire that runs between your transformer and the first of the landscape lights.
5. Locate the end of the wire leading from the Transformer. Place it into the lower por tion of the Connector, in the channel marked “From Transformer”. Lead the wire completely through the Connector. Leave the wire’s cut end bare or apply an endcap. Ensure the wire is straight and aligned with the channel, and rests on the brass teeth. 18 6. Replace the cap over this end of the wire, and press until the cap clips into position. Ensure the cap is turned the right direction. The caps are not reversible.
7. Locate the end of the wire leading to the first landscape light fix ture in the series. Place it into the channel in the top half of the Connector, marked “ To Lights”. 20 8. Align the second cap and press it into position until it snaps in place and is secured to the Connector.
Complete the Installation Reconnect the Transformer 1. Turn the power ON at the circuit breaker or fuse, and/or plug-in your transformer, and turn it ON. Note: It is important the transformer remains ON continuously, and does NOT automatically shut off. Insure that your transformer is set to Manual ON, or Continuous ON. 1. With the Connector at tached to the low-voltage wires, position the Controller’s stake where it will be installed. Loosely guide the top of the Controller with the palm of your hand.
Motion-Sensor Installation Insert Batteries 1. Press your palm against the rear plate and twist counterclock wise (about 5°) to open and access the bat ter y compar tment.
Mount the Sensor Open 2. Inser t (3) AA bat teries. Match the direction of the polarit y markings (+) (−). AA 1.5V AA 1.5V CAUTION: Do not open, short circuit, or mutilate batteries as injury may occur. The Motion Sensor can be mounted onto a wall, or staked to the ground. (Cradle, stake, and pole sold separately.) Mounting to the Wall AA 1.5V IMPORTANT: Dispose of the batteries in accordance with local, state, and federal regulations. 6 f t. 3. Replace the rear plate.
2. Use the enclosed template to mark the location where the sensor will be installed. 4. Slide the Motion Sensor onto the wall mount until it click s in place. 3. Fix the mount to the wall with screws. Use anchors if needed.
Spotlight Installation Pair with App Insert Batteries 1. Press the but ton on the front of the sensor unit. 2. The LED light will flash continuously, indicating that it is ready for pairing. 3. Open the Lightscape App and Search Devices. Follow the prompts to add the sensor and set it in a Zone. 4. Press the but ton on the sensor again to end pairing. When the sensor detects motion, it will turn on. 30 1.
2. Press and squeeze the top and bot tom tabs of the compar tment cover to open it. 3. Place (4) D bat teries into the compar tment. Match the polarit y markings (+) (−). CAUTION: Do not open, short circuit, or mutilate batteries as injury may occur. IMPORTANT: Dispose of the batteries in accordance with local, state, and federal regulations.
5. Replace the back of the spotlight and turn clock wise until it lock s shut. 4. Replace the bat ter y compar tment cover. Press until it snaps into place. 6. When the spotlight has power, it can be added to your system on the app. Assign it the same zone as a sensor to connect them.
Mount the Spotlight Mounting to the Wall 1. Choose a location on the wall 4 to 6 f t. above the ground to mount the Spotlight. Fasten the mount to the wall. Use anchors if needed. 36 2. Twist the locking-ring on the wall mount to loosen it, and inser t the base of the Spotlight.
Stake Mounting 3. Set to the desired angle, and twist the locking-ring to hold the Spotlight in place. 4. Turn the knob to loosen the head and adjust the up / down angle. Tighten the knob to lock in place. 38 1. Screw the stake onto the bot tom of the Spotlight.
Online Resources & Help 2. Turn the knob to loosen it and adjust the angle of the spotlight. Tighten to lock the desired angle. Visit novolinkinc.com for more information about the Lightscape system including tips, installation videos, and news on the latest ways to expand your system. Visit homedepot.com or shopnovolink.com to purchase more Lightscape components or replacement par ts. 3. Use your foot to drive the stake into the ground.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Novolink, Inc. is under license. Other trademarks and trade names are those of their respective owners. FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to par t 15 of the FCC Rules. These limits are designed to provide reasonable protec tion against harmful inter ference in a residential installation.