OUTDOOR STORAGE Co py MODEL #0125 OWNER’S MANUAL Keep this Identification Number in case you need to contact our Customer Service Department.
IMPORTANT! PLEASE READ BEFORE BEGINNING ASSEMBLY Dear Valued Customer, We would like to congratulate you on your purchase of a Lifetime© Outdoor Storage Shed! We are confident that you have made the perfect choice and you will be very pleased with your new storage solution. Lifetime© Outdoor Storage is part of the family of products created and manufactured by Lifetime® Products, Inc.
IMPORTANT! PLEASE READ BEFORE BEGINNING ASSEMBLY t #FGPSF CFHJOOJOH BTTFNCMZ SFNPWF UIF 1BSUT -JTU GSPN UIF DFOUFS PG UIJT 0XOFS T .BOVBM BOE UBLF BO inventory of the parts included with your Outdoor Storage Shed. Also, read through the entire instruction manual. It’s always a great practice to get a feel for the flow of the process and to familiarize yourself with the parts involved. But, try not to get ahead of yourself and start the process out of order.
REGISTER YOUR PRODUCT ONLINE AT WWW.LIFETIME.COM At Lifetime, we are committed to providing innovative and quality products. While registering, you will have the opportunity to give us your feedback. Your input is valuable to us. t :PV DBO BMTP PQU JO UP SFDFJWF OFX QSPEVDU OPUJm DBUJPOT PS QSPNPUJPOT t *O UIF VOMJLFMZ FWFOU PG B QSPEVDU SFDBMM PS TBGFUZ NPEJm DBUJPO ZPVS SFHJTUSBUJPO QSPWJEFT UIF JOGPSNBUJPO XF OFFE UP OPUJGZ ZPV directly.
BEFORE BEGINNING ASSEMBLY Keep the hardware bags and their contents separate. If any parts are missing, call our Customer Service Department. 3FBE UIF i$POHSBUVMBUJPOTw MFUUFS PO QBHF Identify and inventory all parts and hardware using the parts and hardware lists and identifiers in this document. *Two adults required to complete assembly* Only adults should set up the product. Do not allow children in the set-up area until assembly is complete. IF YOU ARE INSTALLING A NEW SHED 1.
ASSEMBLY GUIDE Refer to the following areas throughout the instructions to assist in the assembly process: This area is located at the top, left-hand corner of the page and indicates which tools and hardware are needed to complete the assembly steps on a page. TOOLS AND HARDWARE REQUIRED FOR THIS PAGE SEC This area is located at the top, right-hand corner of the page and shows an image of the product with shaded parts indicating which section is being assembled.
IMPORTANT NOTICES Level Surface Notice: Surface must be leveled before installation. We recommend building a level work space with a concrete or patio style surface. If the surface is not properly leveled, the Outdoor Shed will not assemble correctly. Proper surface leveling will save you time in the long run, so please do not ignore this step.
PARTS & HARDWARE LIST ID Main Parts "': "') "'2 "'( "(2 ")% "(+ AFL "'1 Description $FOUFS 3PPG $BQ 5SVTT (VUUFS $IBOOFM 8BMM 4VQQPSU $IBOOFM 5SVTT #SBDF $IBOOFM $FOUFS 3PPG 1BOFM 8BMM 1BOFM *OOFS 'MPPS 1BOFM Roof Support Strip 5SVTT 4VQQPSU 4USJQ ID Quantity Description Quantity BJK 0125 Hardware Bag BGV Truss Assembly Hardware "", w Y w )FY #PMU ADJ 1/4” Cap Nut AIP Truss Connector ")5 'MPPS #SBDLFU BGT Wall & Roof Installation Hardware ADZ 1/4”
PARTS IDENTIFIER Parts shown at 4% of actual size AGQ Y Center Roof Panel AHD Y Wall Panel v AGJ Y Inner Floor Panel Parts shown at 8% of actual size 20 1/8” AFP Y Truss Support Strip 28 7/8” AFY (x1) Center Roof Cap AFL (x6) Roof Support Strip 71 11/16” AFH Y 5SVTT (VUUFS $IBOOFM 79 1/2 ” AFG (x1) Truss Brace Channel 79 1/2” AFQ Y Wall Support Channel 9
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE REFER TO YOUR CURRENT SHED PLATFORM FOR MATERIALS USED SEC SITE SELECTION 1.1 5IJT FYUFOTJPO LJU BEET BOPUIFS w UP UIF MFOHUI PG ZPVS TIFE #FGPSF CFHJOOJOH FYQBOTJPO PG ZPVS TIFE CF TVSF UIBU ZPVS TJUF DBO BDDPNNPEBUF UIF OFX TJ[F "EE w UP UIF MFOHUI PG ZPVS TJUF T XPPEFO QMBUGPSN (shown) or cement platform; the width will remain the same. This may require the use of additional lumber or other materials.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 NO HARDWARE REQUIRED FOR THIS PAGE **SAVE ALL HARDWARE FOR RE-ASSEMBLY!** If your existing shed is anchored to the ground, remove all anchoring hardware before following these steps. SEC SHED DISASSEMBLY 2.1 Remove the four Center Roof Panels and two Center Roof Caps highlighted below. ! Note: Your shed may be shorter than one shown above.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE SEC 2.3 ! Tip the Wall Panel inward. Note: You’re Shed may be a different length than the Shed shown, but the ideas are the same. SEC 2.4 ! Use a long flat screwdriver to gently pry the bottom corner of the Wall Panel so that it has room to slide on the inside of adjacent Wall Panel. Slide the Wall Panel to the left, and then remove the Panel. Repeat steps 2.2 through 2.4 for the other side of the shed.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 NO HARDWARE REQUIRED FOR THIS PAGE SEC 2.5 Remove the Truss Assembly and set it aside for later. CAUTION As you remove the Wall Panels, have one person support the Truss assembly so that it does not fall over. SEC 2.6 With at least on person on each side of the shed, tip the back section of the shed forward to about a 45° angle and slide the back section away from the shed.
SEC 3 FLOOR ASSEMBLY PLASTIC PARTS REQUIRED Part shown at 4% of actual size v AGJ Y Inner Floor Panel TOOLS REQUIRED Safety Glasses 14
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE SEC FLOOR ASSEMBLY 3.1 Fit together the two Inner Floor Panels (AGJ). AGJ AGJ SEC 3.2 Tip the Inner Floor Panel Assemblies forward at a 45° angle and connect them to the Inner Floor Panels on the main section of the shed.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE SEC 3.3 With at least one person on each side of the shed, tip the back section of the shed forward at about a 45° angle and slide it forward to re-connect it to the rest of the shed.
SEC 4 TRUSS ASSEMBLY HARDWARE BAG REQUIRED: BGV HARDWARE REQUIRED Hardware shown at 50% of actual size Hardware shown at actual size AAK (x10) w Y w )FY #PMU ADJ (x10) 1/4” Cap Nut AHT Y Floor Bracket AIP (x1) 5SVTT (VUUFS $POOFDUPS METAL PARTS REQUIRED Parts shown at 8% of actual size 71 11/16” AFH Y 5SVTT (VUUFS $IBOOFM 79 1/2” AFG (x1) Truss Brace Channel 79 1/2” AFQ Y Wall/Shelf Support Channel 20 1/8” AFP Y Truss Support Strip TOOLS REQUIRED 7/16” Wrench Y Safety Glass
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 4 7/16” Y AAK (x6) AIP (x1) (Not to scale) ADJ (x6) SEC 4.1 TRUSS ASSEMBLY Fit two Truss Support Strips (AFP) together. Bolt Truss Support Strips, Truss Gutter Connector (AIP), and two Truss Gutter Channels (AFH) as shown using the required hardware. AIP AFP AAK AFH AFP ADJ AFH AFP AFP WARNING ! SEC 4.2 Do not overtighten the Cap Nut. If the end of the Bolt breaks through the plastic cap, call our Customer Service Department.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 7/16” Y AAK Y ADJ Y SEC 4.3 Attach Truss Assembly to two Wall Support Channels (AFQ) using 1/4” x 1 1/2” Hex Bolts (AAK) and 1/4” Cap Nuts (ADJ). Do not completely tighten the Cap Nut until after Truss is secured to the Wall. AFQ AAK 4.4 ! Note: Only finger tighten hardware. AFH ADJ AFQ WARNING Do not overtighten the Cap Nut.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 4 7/16” Y AAK Y AHT Y (Not to scale) ADJ Y SEC 4.4 Attach one Floor Bracket (AHT) to the bottom of each Wall/Shelf Support Channel using the required hardware. Tighten all hardware. Repeat this section for all Trusses. You need only do this step if you plan to anchor your Shed. See the “Anchoring the Shed” step at the end of this Owner’s Manual.
SEC 5 WALL & ROOF INSTALLATION HARDWARE REQUIRED HARDWARE BAG REQUIRED: BGT Hardware shown at actual size (*unless otherwise indicated) AED (x4) Y w 'FOEFS 8BTIFS AJA (x4)* Foam Cube ADZ (x60) 1/4” x 5/8” Phillips Pan-Head Screw ACJ (x4) Y w 1IJMMJQT 1BO )FBE 4DSFX METAL PARTS REQUIRED Part shown at 8% of actual size 28 7/8” AFL (x6) Roof Support Strip PLASTIC PARTS REQUIRED Parts shown at 4% of actual size AHD Y Wall Panel Part shown at 8% of actual size AGQ Y Center Roof Pa
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 5 ADZ Y SEC 5.1 Insert a Wall Panel you removed previously as well as the Wall Panel (AHD) QSPWJEFE XJUI UIJT LJU :PV DBO JOTFSU UIF Panels in any of the available locations. Use the 1/4” x 5/8” Phillips Pan-Head Screws you removed previously as well as the 1/4” x 5/8” Phillips Pan-Head Screws (ADZ) provided with this kit to secure the Panels together.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 5 ADZ (x16) SEC 5.2 Connect the Truss Assembly you removed previously as well as the Truss Assembly you built using this kit to the center of each Wall Panel and Window Wall Panel with 1/4” x 5/8” Phillips Pan-Head Screws (ADZ).
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 5 ADZ Y ACJ (x4) AED (x4) SEC 5.3 Connect the Center Roof Panels, Roof Support Strips, and Center Roof Cap you removed previously as well as the Center Roof Panels (AGQ), Roof Support Strips (AFL), and Center Roof Cap (AFY) provided with this kit using 1/4” x 5/8” Phillips Pan-Head Screws (ADZ), #10 x 5/8” Phillips Pan-Head Screws (ACJ), and #10 x 1” Fender Washers (AED). The hole at the end of the Roof Support is for manufacturing purposes only.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE AJA (x4) 5 ADZ (x4) SEC 5.4 $POOFDU UIF (VUUFS $IBOOFMT UP UIF VOEFSTJEF PG UIF CPUUPN PG UIF 3PPG 1BOFMT VTJOH 1/4” x 5/8” Phillips Pan-Head Screws (ADZ) (Fig. 1).
LIFETIME OUTDOOR SHED EQUIPMENT 10-YEAR LIMITED FACTORY WARRANTY THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE. 1. Lifetime outdoor sheds are warranted to the original purchaser to be free from defects in material or workmanship GPS B QFSJPE PG UFO ZFBST GSPN UIF EBUF PG PSJHJOBM SFUBJM QVSDIBTF 5IF XPSE iEFGFDUTw JT EFm OFE BT JNQFSGFDUJPOT UIBU impair the use of the product.
ENHANCE YOUR LIFETIME® PURCHASE BY ADDING ACCESSORIES OR OTHER GREAT PRODUCTS To purchase accessories or other Lifetime Products, visit us at: www.lifetime.