OUTDOOR STORAGE MODEL N° 6414 Co py OWNER’S MANUAL Keep this Identification Number in case you must contact our Customer Service Department.
IMPORTANT! PLEASE READ BEFORE BEGINNING ASSEMBLY Dear Valued Customer, We would like to congratulate you on your purchase of a Lifetime© Outdoor Storage Shed! We are confident that you have made the perfect choice and you will be very pleased with your new storage solution. Lifetime© Outdoor Storage is part of the family of products created and manufactured by Lifetime® Products, Inc.
IMPORTANT! PLEASE READ BEFORE BEGINNING ASSEMBLY s "EFORE BEGINNING ASSEMBLY REMOVE THE 0ARTS ,IST FROM THE CENTER OF THIS /WNER S -ANUAL AND TAKE AN inventory of the parts included with your Outdoor Storage Shed. Also, read through the entire instruction manual. It’s always a great practice to get a feel for the flow of the process and to familiarize yourself with the parts involved. But, try not to get ahead of yourself and start the process out of order. s &/,,/7 4(% ).3425#4)/.3 ).
REGISTER YOUR LIFETIME PRODUCT TODAY! There are benefits to registering your Lifetime product. With our new online product registration form, it’s fast and easy! Register with us at www.lifetime.com and enjoy these great benefits: s 2ECEIVE EXCLUSIVE MONEY SAVING OFFERS FROM "UY,IFETIME COM OUR ONLINE STORE AS WELL AS .
BEFORE BEGINNING ASSEMBLY Keep the hardware bags and their contents separate. If any parts are missing, call our Customer Service Department. 2EAD THE h#ONGRATULATIONSv LETTER ON PAGE Identify and inventory all parts and hardware using the parts and hardware lists and identifiers in this document. *Two adults required to complete assembly* (+ one adult suggested as an instruction reader) Only adults should set up the product. Do not allow children in the set-up area until assembly is complete.
ASSEMBLY GUIDES Refer to the following areas throughout the instructions to assist in the assembly process: TOOLS AND HARDWARE REQUIRED FOR THIS PAGE SEC This area is located at the top, left-hand corner of the page and indicates which tools and hardware are needed to complete the assembly steps on a page. This area is located at the top, right-hand corner of the page and shows an image of the product with shaded parts indicating which section is being assembled.
IMPORTANT NOTICES Level Surface Notice: Surface must be leveled before installation. We recommend building a level work space with a concrete or patio style surface. If the surface is not properly leveled, the Outdoor Shed will not assemble correctly. Proper surface leveling will save you time in the long run, so please do not ignore this step.
PARTS & HARDWARE LIST BOX 1 ID Description Qty BUA BOX 1 METAL KIT BOX AFQ AFO !&# AFR AFD !&( !&0 !&* AFN BTI Wall Support Channel Truss Brace Channel $OOR %ND #HANNEL Corner Channel Door Header Channel 4RUSS 'UTTER #HANNEL 4RUSS 3UPPORT 3TRIP ,ONG 7ALL 3UPPORT #HANNEL %XTENSION Short Wall Support Channel Extension 8 1 4 1 4 DOOR HINGE PARTS KIT AFK AFI Right Hinge Assembly Left Hinge Assembly 1 1 PLASTIC & MISCELLANEOUS PARTS !&3 !'5 !'6 !&4 !'( !') !'3 !'4 !'%
PARTS IDENTIFIER BOX 1 Parts shown at 8% of actual size 79 1/2” AFQ (x8) Wall/Shelf Support Channel 79 1/2 ” AFO (x1) Truss Brace Channel 77 13/16” AFC X Door End Channel 77 1/2 ” AFR (x4) Corner Channel 72 1/4 ” AFD (x1) Door Header Channel 71 11/16” AFH X 4RUSS 'UTTER #HANNEL AFP X Truss Support Strip 16 1/2” 25 1/2” 20 1/8” AFJ X Long Wall Support Channel Extension DOOR HINGE PARTS KIT [BTI] Parts shown at 8% of actual size AFI (x1) Left Hinge Assembly AFK (x1) Right Hinge
PARTS IDENTIFIER BOX 1 (CONT.
PARTS & HARDWARE IDENTIFIER BOX 1 (CONT.
PARTS & HARDWARE IDENTIFIER BOX 1 (CONT.
PARTS & HARDWARE IDENTIFIER BOX 1 (CONT.
PARTS & HARDWARE IDENTIFIER BOX 1 (CONT.
PARTS IDENTIFIER BOX 2 PLASTIC & MISCELLANEOUS PARTS Parts shown at 4% of actual size 1001790 AGZ (x1) Right Door AGO (x1) Left Door 1000272 AHD (x8) Wall Panel 65 1/2” AGC (x1) Top Door Trim 78 9/16” AGD X Side Door Trim 78 7/8” AQX (x4) Corner Trim 15
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1 Concrete (1 cu. yd.) SEC SITE PREPARATION - CONCRETE PLATFORM PREPARATION 1.1 4HE ACTUAL DIMENSIONS OF YOUR SHED AT ITS WIDEST AND LONGEST POINTS ARE X v %NSURE YOU SELECT A SITE THAT will accommodate these measurements.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2” x 4” x 120 1/2” (x4) (Not included) 2” x 4” x 34” X .OT INCLUDED 16d 3” Common Nail (x16) (Not included) SEC ALTERNATIVE SITE PREPARATION: OPTION 1 - WOOD PLATFORM ASSEMBLY 1.2 %NSURE ALL LUMBER USED IS TREATED AND APPROVED FOR OUTDOOR USE "UILD OUTSIDE FRAME TO v X v outside dimensions: ! Note: Whenever possible, you should use the surfaces described on Page 7.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1 34” x 27 1/2” x 3/4” Treated Plywood (x1) (Not included) 8d 1 1/2” Common Nail X (Not included) 34” x 96” x 3/4” Treated Plywood (x1) (Not included) SEC ALTERNATIVE SITE PREPARATION: OPTION 1 - WOOD PLATFORM ASSEMBLY (CONT) 1.3 Square up the frame by measuring from corner to corner. Measurement A should equal Measurement B. B A ! Note: All lumber must be rated for outdoor use. SEC 1.4 Cut Plywood into sizes called for below.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 1 2” x 4” x 124” X .OT INCLUDED 2” x 6” x 27” X .OT INCLUDED Pea Gravel #UBIC &EET (Not included) 8d 1 1/2” Common Nail (x16) (Not included) L-Bracket (x4) (Not included) ALTERNATIVE SITE PREPARATION: OPTION 2 - FILLED WOOD FRAME ASSEMBLY SEC #UT OUTSIDE FRAME TO v X v outside dimensions. Lay boards flat so widest parts face up. Ensure frame is level. Square up the frame by measuring from corner to corner.
SEC 2 FLOOR ASSEMBLY HARDWARE REQUIRED NO HARDWARE PROVIDED FOR THIS SECTION METAL PARTS REQUIRED NO METAL PARTS REQUIRED FOR THIS SECTION PLASTIC PARTS REQUIRED Parts shown at 4% of actual size 61 25/32” AGS X Outer Floor Panel A 61 25/32” AGT X Outer Floor Panel B TOOLS REQUIRED Phillips Screwdriver Hammer Drill Safety Glasses 20 3/8” Masonry Bit
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 NO HARDWARE REQUIRED FOR THIS PAGE SEC FLOOR PANEL ASSEMBLY 2.1 Hold one (1) Outer Floor Panel “B” (AGT) at an angle against one (1) Outer Floor Panel “A” (AGS) so the tabs on Panel h"v l T UNDERNEATH 0ANEL h!v AND THE TABS ON 0ANEL ! l T UNDERNEATH 0ANEL h"v 4HEN LAY 0ANEL h"v m AT AGT AGS SEC 2.2 Repeat the previous step to connect the next two Outer Floor Panels.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 2 NO HARDWARE REQUIRED FOR THIS PAGE TWO PEOPLE REQUIRED FOR THIS STEP SEC 2.3 ! SEC 2.4 If you plan on anchoring your shed to your concrete or wood platform, lay your Floor out on your platform in the position you would like your shed to face. While another person holds the Floor in place, punch out one hole by each seam and mark the position of that hole on the platform beneath. Note: Pick only one hole by the seam.
SEC 3 TRUSS ASSEMBLY HARDWARE REQUIRED Hardware shown at 50% of actual size Hardware shown at actual size AAK (x10) v X v (EX "OLT ADJ (x10) 1/4” Cap Nut AHT X Floor Bracket AIP (x1) 4RUSS 'UTTER #ONNECTOR METAL PARTS REQUIRED Parts shown at 8% of actual size 71 11/16” AFH X 4RUSS 'UTTER #HANNEL 79 1/2” AFG (x1) Truss Brace Channel 79 1/2” AFQ X Wall/Shelf Support Channel 20 1/8” AFP X Truss Support Strip PLASTIC PARTS REQUIRED NO PLASTIC PARTS REQUIRED IN THIS SECTION TOOLS
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 3 7/16” X AAK (x6) AIP (x1) (Not to scale) ADJ (x6) SEC 3.1 TRUSS ASSEMBLY Fit two Truss Support Strips (AFP) together. Bolt Truss Support Strips, Truss Gutter Connector (AIP), and two Truss Gutter Channels (AFH) as shown using the required hardware. AIP AFP AAK AFH AFP ADJ AFH AFP AFP WARNING ! SEC 3.2 Do not overtighten the Cap Nut. If the end of the Bolt breaks through the plastic cap, call our Customer Service Department.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 7/16” X AAK X ADJ X SEC 3.3 Attach Truss Assembly to two Wall Support Channels (AFQ) using 1/4” x 1 1/2” Hex Bolts (AAK) and 1/4” Cap Nuts (ADJ). Do not completely tighten the Cap Nut until after Truss is secured to the Wall. AFQ AAK 3.4 ! AFH Note: Only finger tighten hardware. ADJ AFQ WARNING Do not overtighten the Cap Nut.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 7/16” X AAK X AHT X (Not to scale) ADJ X SEC 3.4 Attach one Floor Bracket (AHT) to the bottom of each Wall/Shelf Support Channel using the required hardware. Tighten all hardware. Repeat this section for all Trusses. You need only do this step if you plan to anchor your Shed. See the “Anchoring the Shed” step at the end of this Owner’s Manual. AFQ ADJ AAK AHT 3.
SEC 4 WALL PANEL INSTALLATION HARDWARE REQUIRED Hardware shown at actual size ADZ X 1/4” x 5/8” Pan-Head Screw METAL PARTS REQUIRED Part shown at 8% of actual size 77 1/2 ” AFR (x4) Corner Channel PLASTIC PARTS REQUIRED Parts shown at 4% of actual size 1000272 AHD (x8) Wall Panel TOOLS REQUIRED #2 Phillips Screwdriver 3/8” Wrench Safety Glasses 27
SEC TOOLS AND PARTS REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE SEC WALL ASSEMBLY 4.1 Lock a Wall Panel (AHD) to the front, right corner of the Floor by inserting the tabs at the bottom of the Wall Panel into the slots on the Floor. After inserting the tabs, slide the Wall Panel to the left. AHD SEC 4.2 Insert a second Wall Panel (AHD) to the right edge of the Floor and slide it to the left towards the first Wall Panel.
SEC TOOLS AND PARTS REQUIRED FOR THIS PAGE 4 ADZ X SEC 4.3 Align the holes in a Corner Channel (AFR) with the holes in the two Wall Panels and secure the Corner Channel to THE 7ALL 0ANELS USING TWELVE 1/4” x 5/8” Phillips Pan-Head Screws (ADZ). You will perform this step for each corner of the shed. AFR (x1) 77 1/2” ! Note: A second adult should apply pressure to the opposite side of the wall for easy insertion of screws. SEC 4.
SEC TOOLS AND PARTS REQUIRED FOR THIS PAGE 4 ADZ X SEC 4.5 Insert the next Wall Panel (AHD) along the left edge of the Floor as shown. Align the holes in a Corner Channel (AFR) with the holes in the two corner Wall Panels and secure the Corner Channel to the Wall Panels using twelve 1/4” x 5/8” Phillips Pan-Head Screws (ADZ). Align the holes in the Wall Panels and secure using six (6) 1/4” x 5/8” Phillips Pan-Head Screws (ADZ). AHD SEC 4.
SEC 5 TRUSS & WALL/SHELF SUPPORT CHANNEL INSTALLATION HARDWARE REQUIRED Hardware shown at actual size (*Unless noted otherwise) ADZ (x64) 1/4” x 5/8” Pan-Head Screw (Not all screws are used) AAK (x18) v X v 0AN (EAD 3CREW ADJ (x18) 1/4” Cap Nut METAL PARTS REQUIRED Parts shown at 8% of actual size 79 1/2” AFQ (x6) Wall/Shelf Support Channel 16 1/2” 25 1/2” AFJ X Long Extension Channel AFN (x4) Short Extension Channel Part not shown at any particular scale Truss Assembly (x1) PLASTI
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADZ (x16) SEC 5.1 TRUSS INSTALLATION Secure the Truss Assembly to the center of the Wall Panels on the left and right walls with sixteen (16) 1/4” x 5/8” Pan-Head Screws (ADZ).
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 7/16” X AAK X ADJ X SEC 5.2 SHORT WALL SUPPORT CHANNEL EXTENSION ASSEMBLY Slide a Short Wall Support Channel Extension (AFN) into the top of a Wall Support Channel (AFQ) AND SECURE WITH TWO 1/4” x 1 1/2” Hex Bolts (AAK) AND TWO 1/4” Cap Nuts (ADJ). Repeat this step for the remaining three Short Wall Support Extensions. AFN Use these two holes SEC 5.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 5 7/16” X AAK (x6) AHT (x6) (Not to scale) ADJ (x6) SEC 5.4 Attach one Floor Bracket (AHT) to the bottom of each Wall Support Channel. Tighten all hardware. Repeat this section for all Trusses. You need only do this step if you plan to anchor your Shed. See the “Anchoring the Shed” step at the end of your Owner’s Manual. AFQ ADJ AAK AHT WARNING Do not overtighten the Cap Nut.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 5 ADZ (x16) FRONT WALL SUPPORT CHANNEL INSTALLATION SEC 5.5 Using the middle set of eight pre-made holes in the Left, Front Wall Panel, secure a Short Wall Support Channel Assembly to the Left, Front Wall Panel using eight (8) 1/4” x 5/8” Pan-Head Screws (ADZ). Repeat this step for the Right, Front Wall Panel.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 5 ADZ X SEC 5.6 REAR WALL SUPPORT CHANNEL INSTALLATION Using the middle set of eight pre-made holes in the right, rear Wall Panel, secure a Short Wall Support Channel Assembly to the right, rear Wall Panel using eight (8) 1/4” x 5/8” Pan-Head Screws (ADZ). Repeat this step for the Left, Rear Wall Panel (Not shown).
SEC 6 LEFT DOOR ASSEMBLY HARDWARE REQUIRED Hardware shown at of actual size ADZ (x9) X 0AN (EAD 3CREW ADW X X 0HILLIPS Pan-Head Screw AEE X X v &LAT 7ASHER ACH X v X v #ARRIAGE "OLT ADJ X #AP .
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE AHM X SEC LEFT DOOR ASSEMBLY 6.1 Rest Left Door (AGO) with front side down. Position Deadbolt Latches (AHM) in slots at top and bottom of Door then slide Door End Channel (AFC) onto the Door. AFC AGO Back of Door AHM Top AHM Bottom ! Note: The Door End Channel fits onto Door with the flat side up (facing the Deadbolt Latches).
AIB (x1) ADZ (x9) SEC 6.2 Attach three Door Braces (AFB) to the back of the Door with 1/4” x 5/8” Phillips Pan-Head Screws (ADZ). ADZ AFB ADZ ADZ AFB AFB SEC 6.3 Slip the Left Door Strike Plate (AIB) over the Left Door and align the holes. AIB ! Note: You may need to nudge the Door End Channel to make these holes line up with the gap in the Door.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 7/16” ACH X ADJ X ADW X AIA (x1) AEE X AHZ (x1) SEC 6.4 Attach the Left Door Lock Bracket (AIA) TO THE 3TRIKE 0LATE WITH TWO 1/4” x 1 1/2” Carriage Bolts (ACH) AND TWO 1/4” Cap Nuts (ADJ). ADJ AIA ACH SEC 6.5 Attach the Left Door Handle (AHZ) USING THREE #10 x 1/2” Flat Washers (AEE AND THREE #10 x 3/4” Pan-Head Screws (ADW).
SEC 7 RIGHT DOOR ASSEMBLY HARDWARE REQUIRED Hardware shown at of actual size ADZ (x9) X 0AN (EAD 3CREW ADW (x4) X 0AN (EAD 3CREW ACI X X #ARRIAGE "OLT AHY (x1) Latch Spring (ARDWARE SHOWN AT OF ACTUAL SIZE AIO (x1) Thumb Lever AAB X 1/4” Centerlock Nut Hardware shown at 15% of actual size AHV (x1) Door Latch AIK (x1) Right Door Handle AIL (x1) Right Door Lock Bracket ADB X v X v 3TEEL 3PACER AEE X X v &LAT 7ASHER AEB X 1/4” Flat Was
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE NO HARDWARE REQUIRED FOR THIS PAGE SEC 7.1 RIGHT DOOR ASSEMBLY Rest Right Door (AGZ) with front side down, then slide Door End Channel (AFC) onto the Door.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADZ (9) AIO (x1) AIK (x1) SEC 7.2 Attach three Door Braces (AFB) to the back of the Door with nine (9) 1/4” x 5/8” Phillips Pan-Head Screws (ADZ). ADZ ADZ ADZ AFB AFB AFB SEC 7.3 Fit the Thumb Lever (AIO) knobs into the grooves in the Right Door Handle (AIK).
AEE X ADW X SEC 7.4 Rotate the Thumb Lever into the Handle. Slide forward until the Knobs fit into the holes in the Handle. Knobs snap into holes SEC 7.5 Attach the Handle and Thumb Lever to the Door using the required hardware.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 7/16” AHX (x1) (Not to scale) AHV (x1) (Not to scale) ACI X AAB X AIL (x1) (Not to scale) AEB X ADB X SEC 7.6 Connect the Right Door Handle to the Right Door using the hardware shown. Tighten all hardware.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE AHY (x1) AHW (x1) (Not to scale) ADW (x1) SEC 7.7 Line up the hole in the Latch Block (AHW) with the hole in the Thumb Lever (AIO), and secure in place with a #10 x 3/4” Phillips Pan-Head Screw (ADW). ADW AIO ! AHW Note: The lip of the Latch Block (AHW) fits under the Thumb Lever (AIO). SEC 7.8 Attach Latch Spring (AHY) to handle assembly. Set the Door aside.
SEC 8 GABLE ASSEMBLY HARDWARE REQUIRED Hardware shown at actual size AEE (x10) X v &LAT 7ASHER ADZ (x8) 1/4” x 5/8” Pan-Head Screw ADW (x10) X v 0AN (EAD 3CREW METAL PARTS REQUIRED NO METAL PARTS REQUIRED FOR THIS SECTION PLASTIC PARTS REQUIRED Parts shown at 4% of actual size Parts shown at 15% of actual size 1000472 AGH X 'ABLE (ALF AGP X Louvered Vent 1000470 AGI X 'ABLE (ALF AIQ X Vent Screen TOOLS REQUIRED Phillips Screwdriver Safety Glasses 47
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADZ (x8) SEC GABLE ASSEMBLY 8.1 Set the edge of Gable Half 2 (AGI) over the edge of Gable Half 1 (AGH) as shown. AGI AGH SEC 8.2 3ECURE THE TWO 'ABLE (ALVES TOGETHER USING FOUR 1/4” x 5/8” Pan-Head Screws (ADZ).
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 8 ADW (x10) AEE (x10) SEC 8.3 Attach the Louvered Vent (AGP) and Vent Screen (AIQ) TO THE 'ABLE Assembly using five (5) #10 x 1/2” Flat Washers (AEE) and five (5) #10 x 3/4” Phillips Pan-Head Screws (ADW) 3ET THE 'ABLE !SSEMBLY ASIDE UNTIL LATER Repeat this section for the second Gable.
SEC 9 DOOR & ENTRY GABLE INSTALLATION HARDWARE REQUIRED Hardware shown at actual size (*Unless noted otherwise) *AHL (x1) Dead Bolt Strike Plate ADZ X 1/4” x 5/8” Pan-Head Screw ACH (x4) v X v #ARRIAGE "OLT ADX X X v 0AN (EAD 3CREW ADJ (x8) 1/4” Cap Nut *AHN X Floor Bracket ACA (x4) v X v #ARRIAGE "OLT AEB (x4) 1/4” Flat Washer METAL PARTS REQUIRED Parts shown at 8% of actual size AFI X Left Hinge Assembly AFK X Right Hinge Assembly PLASTIC PARTS REQUIRED Pa
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 9 ADZ (x10) 2 ADULTS REQUIRED FOR THESE STEPS SEC FRONT GABLE INSTALLATION 9.1 3ET THE &RONT 'ABLE !SSEMBLY IN FRONT OF THE TWO SHORT 7ALL 3UPPORT #HANNELS AND ON THE TWO FRONT 7ALL 0ANELS AS shown. SEC 9.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 9 ACA (x4) ADJ (x4) AHN X (Not to scale) SEC 9.3 DOOR FRAME ASSEMBLY & INSTALLATION Insert a 1/4” x 1/2” Carriage Bolt (ACA) through the top hole of the Right Door Hinge (AFK) as shown, and secure with a 1/4” Cap Nut (ADJ). Only hand tighten the Cap Nut for now. Repeat this step for the Left Door Hinge (AFI). ACA ACA ADJ ADJ AFK AFI Right Door Hinge Left Door Hinge SEC 9.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 9 ADZ (x5) SEC DOOR FRAME INSTALLATION 9.5 Slide the Right Door Hinge Assembly over the right, front Wall Panel and secure the Hinge Assembly to the Wall Panel using five (5) 1/4” x 5/8” Pan-Head Screws (ADZ).
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADZ (x5) SEC 9.6 Slide the Left Door Hinge Assembly over the left, front Wall Panel and secure the Hinge Assembly to the Wall Panel using five (5) 1/4” x 5/8” Pan-Head Screws (ADZ).
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 9 ADZ (x4) SEC 9.7 Carefully remove the 1/4” Cap Nut from the top of the Left Door Hinge Assembly. Place the Door Header at THE TOP OF THE $OOR (INGE !SSEMBLY SO v X v #ARRIAGE "OLT GOES THROUGH THE ELONGATED HOLE ON THE $OOR Header as shown. Carefully replace the 1/4” Cap Nut. Repeat this step for the Right Door Hinge Assembly. Finally, SECURE THE $OOR (EADER TO THE &RONT 'ABLE USING FOUR 1/4” x 5/8” Pan-Head Screws (ADZ) at the locations shown.
NO HARDWARE REQUIRED FOR THIS PAGE SEC DOOR INSTALLATION 9.8 Slide the edge of the Left Door Assembly down into the end of the Left Hinge Assembly as shown.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 9 ADJ (x4) AEB (x4) ACH (x4) SEC 9.9 Align the notch in the Left Door Assembly with the two holes in the end of the Left Hinge Assembly, and insert TWO 1/4” x 1 1/2” Carriage Bolts (ACH) 3ECURE THE $OOR TO THE (INGE USING TWO 1/4” Flat Washers (AEB) and two 1/4” Cap Nuts (ADJ). Repeat these steps for the Right Door Assembly.
AHL (x1) (Not to scale) ADX X SEC 9.10 Secure the Deadbolt Strike Plate (AHL) TO THE &LOOR USING TWO #10 x 1/2” Pan-Head Screws (ADX).
SEC 10 TRIM INSTALLATION HARDWARE REQUIRED Hardware shown at actual size (*Unless indicated otherwise) ADX (56) X v 0AN (EAD 3CREW ACK (4) X v 0AN (EAD 3CREW *AGA X Corner Trim Bracket *AHQ (x4) Door Trim Bracket *AHR X Door Trim Clip METAL PARTS REQUIRED NO METAL PARTS REQUIRED FOR THIS SECTION PLASTIC PARTS REQUIRED Parts shown at 4% of actual size 65 1/2” AGC (x1) Top Door Trim 78 9/16” AGD X 3IDE $OOR 4RIM 78 7/8” AQX (x4) Corner Trim TOOLS REQUIRED Phillips Screwdriv
SEC TOOLS AND PARTS REQUIRED FOR THIS PAGE ADX (8) AHQ (x4) (Not to scale) SEC DOOR TRIM INSTALLATION 10.1 Slide Side Door Trim (AGD) into place onto Door Hinge Brackets. AGD AGD SEC 10.2 Attach four (4) Door Trim Brackets (AHQ) above the Door frame at the locations shown. AHQ ADX ! Note: Look for screw hole locator marks above the Door frame.
SEC TOOLS AND PARTS REQUIRED FOR THIS PAGE AHR X (Not to scale) SEC 10.3 Slide Door Trim Clips (AHR) into the top of the Side Door Trim (Fig. 1), on each side of the Door. Slide the Top Door Trim (AGC) INTO PLACE AND SECURE WITH THE $OOR 4RIM #LIPS &IG AGC AHR AGC AHR AGD AGD Fig. 2 Fig. 1 ! Note: You may need to slightly bend the tab outward with pliers.
SEC TOOLS AND PARTS REQUIRED FOR THIS PAGE 10 AGA X (Not to scale) ADX (x48) ACK (x4) 12. Trim (Continued) CORNER TRIMInstallation INSTALLATION SEC Door 10.4 Snap six (6) Black Trim Brackets (AGA) TO A CORNER OF THE 3HED &ASTEN EACH "RACKET WITH TWO #10 x 1/2” Screws (ADX). There are no pilot holes in the Shed Wall; the Screws are inserted directly into the plastic.
SEC 11 ROOF & REAR GABLE INSTALLATION HARDWARE REQUIRED Hardware shown at actual size (*Unless otherwise noted) ADZ (x86) 1/4” x 5/8” Pan-Head Screw (Not all screws will be used) *AJA (x4) Foam Cube ADK (x1) #AP .
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 11 ADZ X SEC 11.1 Install two Outer Roof Panels “A” & “B” (AGU & AGV) at the front of the shed as shown. The top of the Wall Panel fits INTO THE GROOVE NEAR THE BOTTOM EDGE OF THE 0ANEL !LIGN THE HOLES IN THE 7ALL 0ANEL %NTRY 'ABLE AND 4RUSS !SSEMBLY WITH THOSE IN THE /UTER 2OOF 0ANEL 3ECURE THE /UTER 2OOF 0ANELS TO THE %NTRY 'ABLE 7ALL 0ANELS AND 4RUSS !SSEMBLY USING TWENTY FOUR 1/4” x 5/8” Pan-Head Screws (ADZ).
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 11 ADZ X SEC 11.2 )NSTALL THE 2EAR 'ABLE !SSEMBLY TO THE TOPS OF THE REAR 7ALL 0ANELS USING SIXTEEN 1/4” x 5/8” Pan-Head Screws (ADZ) !LSO SECURE THE 2EAR 'ABLE !SSEMBLY TO THE 7ALL 3UPPORT #HANNEL %XTENSIONS USING SIX 1/4” x 5/8” Pan-Head Screws (ADZ).
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE ADZ X SEC 11.3 Install the last two Outer Roof Panels “A” & “B” (AGU & AGV) at the rear of the shed as shown. Secure the Outer 2OOF 0ANELS TO THE 2EAR 'ABLE AND 4RUSS !SSEMBLY USING TWENTY FOUR 1/4” x 5/8” Pan-Head Screws (ADZ).
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 11 ADZ (x8) ACJ (x4) AED (x4) SEC 11.4 3TARTING AT THE FRONT OF THE SHED INSTALL THE TWO End Roof Caps (AGE) to the Roof. Connect the Roof Caps to the 4RUSSES AND 'ABLES USING 1/4” x 5/8” Pan-Head Screws (ADZ) and to the Roof Panels using #10 x 5/8” Pan-Head Screws (ACJ) and #10 x 1” Fender Washers (AED). Only use a hand screwdriver on this step ADZ Attach Roof Caps to both sides of Trusses using 1/4” x 5/8” Pan-Head Screws (ADZ).
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 11 ADZ (x4) SEC 11.5 Connect a Roof Cap Cover (AHA) to the Front of the Shed as shown using the required hardware. Repeat this step for the rear of the shed.
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 11 7/16” ADX (x4) ACF (x1) ADK (x1) SEC 11.6 Connect a Gable Truss Brace (AFF) BETWEEN THE FRONT 4RUSS !SSEMBLY AND %NTRY 'ABLE AND THE REAR 4RUSS AND 2EAR 'ABLE !SSEMBLIES USING TWO #10 x 1/2” Pan-Head Screws (ADX) EACH 3ECURE THE 'ABLE 4RUSS "RACE INTO THE $OOR (EADER #HANNEL ON %NTRY 'ABLE USING ONE #10 x 5/16” Pan-Head Screw (ACF) and one (1) #10 Cap Nut (ADK).
ADZ (x4) SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 11 AJA (x4) SEC Along the outside of the shed, underneath the eaves, fasten the Truss Assemblies to the Roof Panels using two 1/4” x 5/8” Pan-Head Screws (ADZ) per side. 11.7 ADZ ADZ SEC Insert two Foam Cubes (AJA) at each truss location. 11.
SEC 12 PEGBOARD STRIP INSTALLATION HARDWARE REQUIRED Hardware shown at actual size Hardware shown at 50% of actual size ADW (x10) v X v 0AN (EAD 3CREW AIJ X Toolholder AIG (x1) 4” Double-Arm Hook AII X L-Hook AIF (x1) v $OUBLE !RM (OOK AIH X J-Hook METAL PARTS REQUIRED NO METAL PARTS REQUIRED FOR THIS SECTION PLASTIC PARTS REQUIRED Parts shown at 15% of actual size AFU X Pegboard Strip TOOLS REQUIRED Phillips Screwdriver Safety Glasses Level 71
ADW (x10) SEC PEGBOARD STRIP INSTALLATION 12.1 Using a level, position the Pegboard Strip (AFU) in any desired location along a Wall Panel wall. Screw the Pegboard Strip to the Wall using five (5) #10 x 3/4” Phillips Pan-Head Screws (ADW). See Note. Repeat this step for second Pegboard Strip. ! Note: The Pegboard Strip is screwed directly into the plastic. Line up the Strip anywhere on Wall so holes are over plastic (and not over a groove in the Wall).
SEC 13 SHELF ASSEMBLY HARDWARE REQUIRED Hardware shown at actual size ADX (x68) X v 0AN (EAD 3CREW (Not all are used) AEE (x68) X h &LAT 7ASHER (Not all are used) METAL PARTS REQUIRED Parts shown at 15% of actual size AIY (x10) h 3HELF "RACKET AIZ (x4) h 3HELF "RACKET PLASTIC PARTS REQUIRED Parts shown at 4% of actual size 1002314 1002315 AFS (x5) v X v 3HELF AFT X v X v 3HELF TOOLS REQUIRED Phillips Screwdriver Safety Glasses 73
SEC PARTS & HARDWARE REQUIRED FOR THIS PAGE 13 ADX X AEE X SEC 10“ & 14“ SHELF ASSEMBLY 13.1 Insert the 10“ & 14“ Shelf Support Brackets (AIY & AIZ) into the slots of adjacent Wall/Shelf Support Channels. Insert the Shelf Support Brackets at an angle, and then set them straight. AIY or AIZ SEC 13.2 Place the 10“ x 30“ and 14“ x 30“ Shelves (AFS and AFT) on their respective Shelf Support Brackets and fasten them with #10 x 1/2“ Pan-Head Screws (ADX) and #10 x 1/2“ Flat Washers (AEE).
SEC 14 FINAL STEPS HARDWARE REQUIRED Hardware shown at actual size ADZ (x4) 1/4” x 5/8” Pan-Head Screws METAL PARTS REQUIRED NO METAL PARTS REQUIRED FOR THIS SECTION PLASTIC PARTS REQUIRED NO PLASTIC PARTS REQUIRED FOR THIS SECTION TOOLS REQUIRED Safety Glasses 75
SEC TOOLS AND HARDWARE REQUIRED FOR THIS PAGE 14 ADZ (x4) SEC DOOR SPACING ADJUSTMENT 14.1 9OU MAY NEED TO MOVE THE TOPS AND OR BOTTOMS OF THE DOORS TO ELIMINATE UNEVEN GAPS ,OOSEN THE #ARRIAGE Bolts at the four corners of the Door Frame. Loosen all screws in the left and right Door Hinges by a half a turn. Move Doors until gaps are even. Re-tighten all hardware. After all hardware has been retightened, secure the hinges to the Floor using four (4) 1/4” x 5/8” Pan-Head Screws (ADZ).
CLEANING & CARE 12 Congratulations on your Lifetime® Outdoor Shed purchase. By following the instructions below, your new Lifetime shed should provide you with years of service and enjoyment. Cleaning and Care The polyethylene walls and shelves are stain- and solvent resistant. Most stains can be removed, using a mild soap and a soft-bristled brush. Abrasive cleaning materials may scratch the plastic and are not recommended.
LIFETIME OUTDOOR SHED EQUIPMENT 10-YEAR LIMITED FACTORY WARRANTY THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE. 1. Lifetime outdoor sheds are warranted to the original purchaser to be free from defects in material or workmanship FOR A PERIOD OF TEN YEARS FROM THE DATE OF ORIGINAL RETAIL PURCHASE 4HE WORD hDEFECTSv IS DEl NED AS IMPERFECTIONS THAT impair the use of the product.
ENHANCE YOUR LIFETIME® PURCHASE BY ADDING ACCESSORIES OR OTHER GREAT PRODUCTS To purchase accessories or other Lifetime Products, visit us at: www.lifetime.
