OWNERS INSTA LLATION AND OPERATING MANUAL LIFESMART INFRARED HEATER Model: LS1000HH13 Safety Notice Please read this entire Installation and Operating Manual BEFORE installing and using your new Infrared Heater. Failure to fully understand and follow instructions may result in property damage, bodily injury, or even death. If the Infrared Heater in not used properly, a house fire may result. For everyone’s safety, FOLLOW all Installation and Operating Directions.
Save These Instructions TABLE OF CONTENTS Topic Page(s) Introduction & Specifications 3 Important Safety Information 4-5 Frequently Asked Questions 6-8 Heater Operation 9 Heater Placement 10 Users Guide 11-12 Air Filter Maintenance 13 Warranty 14-15 Warranty Claim Contact Information 16 *Contents in the box: 1. Infrared heater (1unit) 2.
. Remote Control (2 AAA batteries not included) (2pcs) 3
INTRODUCTION Thank you for choosing one of the best Infrared distribution heaters available on the market today. Our Infrared Heater is a very safe and effective room heater. It produces safe, clean and economical heat by utilizing quartz infrared heating elements. The heating process of the Infrared Heater is similar to the way the sun warms the earth. The infrared elements warm the heat chamber and the whisper quiet fan distributes the accumulated warmth.
IMPORTANT SAFETY INSTRUCTIONS READ AND UNDERSTAND ALL INSTRUCTIONS, SAFETY WARNINGS, AND FAQ’s BEFORE USING THE HEATER WARNING! ! POTENTIAL FOR ELECTRICAL HAZARD IF NOT ADHERED TO! When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. This heater must be plugged into a 120V, 15 amp (or more) circuit of its own.
9. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations, nor any locations that use GFCI outlets. 10. Never place heater where it may fall into a bathtub or other water receptacles. 11. Do not run cord under carpet. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over. 12.
FREQUENTLY ASKED QUESTIONS (FAQ’S) My heater emits a “strange” odor when I first open the box/when I turn the heater on for the first time. Why? These are both normal. This heater is treated with a special heat safe/resistant coating. This odor will sometimes be present when the box is opened, and may be compared to a heaters version of “new car smell.” Also, similar to all hearth appliances (woodstoves, etc.
I don’t have a grounded outlet; can I use adapters, a 2-‐prong power strip, or remove the ground prong from the cord? Definitely NOT! If you don’t have a grounded outlet, contact a certified electrician for advice. Removing or altering any part of the heater’s original design or intent (including the power cord) will not only void the warranty, but will make you liable for any unexpected or hazardous results.
My fan runs at all times, even when the heat has cycled off. Why? This is normal. Although the heat cycles off, the fan stays on until the chamber is cool. If the temperature falls below the desired set temperature during the time the fan is cooling, the heating elements will cycle back on. This will not allow for the fan to completely cool off the chamber, and shut down. The fan seems to run continuously. It is a safety mechanism to prevent overheating.
HEATER OPERATION Here is a small description of how our heaters work: Operation Mechanism: 1) Air is brought into the heater through an easy to clean, washable filter at the rear of the unit. 2) The highly efficient, one-speed, high volume fan pushes filtered air through the chamber, across the heat elements. 3) During this exchange, heat is accumulated and transferred to the air in the chamber.
HEATER PLACEMENT By using this infrared heater you can efficiently heat up to 1500 of unobstructed square feet. This heater is NOT intended to replace your home’s furnace. Rather, it is designed to be a supplement to it. It is not an instant heater, and on occasions (depending on various factors), can take up to 24 hours for a room to reach the desired temperature.
USER’S GUIDE Plug your Infrared Heater power cord into a 120V, 15amp (or higher) three-prong receptacle. To Turn the Heater On: 1. Turn the Master toggle switch in the back of the heater to the “On/Lit” position. 2. Press the “Power” button on the front control panel or “ON/OFF” button on the remote control. Heater Default Temperature: The heater’s default temperature every time it is powered “on” is 72°F.
To Set Heat Mode: Press the “High/Low/Eco” button on the control panel or “H/L/E” on the remote control to switch between the High, Low, and Eco modes. The corresponding High, Low or Eco light will switch on. Note that in all modes, the fan speed will remain the same. Heating Process: In the High Mode, all heating elements will engage for full 1500 Watt heating capacity. In the Low mode, corresponding heating elements will engage to heat at 1000 Watts, to save energy.
FILTER MAINTENANCE Your Infrared Heater is equipped with an easy to clean, washable static filter. Regular cleaning and maintenance of your filter will ensure a lifetime of trouble-free use. 1. Turn off the heater. Locate the filter at the rear of the heater and lift out (some filters may be held on by brackets. Others may be magnetic. Others may require loosening up some screws). 2. Rinse the filter by spraying warm tap water through the filter.
Limited Manufacturer Warranty 1 Year Limited Warranty: LIFESMART warrants this heater against defects in materials and workmanship on functional parts, for a period of 1 year from the original date of purchase. Your sales receipt showing the date of purchase of the product is your proof of purchase. Keep it in a safe place for future reference.
Warranty Limitations This warranty does not apply if the unit has been subject to negligence, fabrication, misuse, abuse, or repairs (unless authorized verbally, or in writing, by an Authorized LIFESMART Representative) alteration by non LIFESMART authorized personnel, inappropriate installations, or any case beyond the control of LIFESMART.
Customer Service and Support To Obtain Warranty Support or Advice, Please Complete These Two Easy Steps: Contact LIFESMART PRODUCTS Technical Support E-mail: Warranty@lifesmartproducts.com Phone: 1-866-484-2066 or 1-214-614-2509 Visit us: www.lifesmartproducts.com You will need to provide the unit's model number, serial number (located on the heater’s rear panel ), date of purchase, retailer of purchase, a daytime phone number, and possibly a copy of your receipt. Be Patient, Clear, and Concise.
