User's Manual

ManualsBrandsLifeShield ManualsElectronicsWireless Security Sensor

InGrid Sensor Installation Instructions

InGrid Sensor Kit Contents:

Sensors

Brackets

Magnets

Bracket Spacers

Magnet Spacers

Sensor Extensions

Sensor Sensor Bracket Sensor Bracket Tape

Magnet Magnet Tape Bracket Spacer Magnet Spacer

Sensor Extension

IMPORTANT:

INSTALL SENSORS ONE AT A TIME FOLLOWING

THE STEPS IN THE EXACT ORDER.

IMPORTANT:

DO NOT CLIP THE SENSOR INTO THE BRACKET

UNTIL THE BRACKET AND MAGNET ARE

INSTALLED ON THE DOOR OR WINDOW.

Bracket and Magnet Installation

Doors

Determine Bracket and Magnet Location

The Bracket and Magnet should be positioned on

interior side of door within ¾” of each other.

Bracket

Magnet

Various mounting positions that will work for

attaching sensors to doors:

Top View of Door

IMPORTANT: The maximum distance between the

bracket and magnet should be no more than 3/4 inch

Door frame is higher than door. To bring Bracket in

alignment, slide spacer on to Magnet.

Bracket on angled door frame and Magnet on door.

Place Bracket at 90 degree angle to Magnet on door

Note:

o Insufficient Mounting Space: If your door

frame does not provide enough room for

mounting the Bracket you may need to use a

sensor extension. See the Sensor Extension

Instructions in the User Guide.

o Metal Doors and Windows: If you are

mounting a magnet to a metal door or metal

window, install a spacer under the magnet to

maintain performance.

Add Spacers (If Needed)

If Bracket and Magnet do not align within ¾ inch, add

Spacers to either the Bracket or Magnet to make them

level.

Example: Spacer added to Magnet to close the gap

between the Bracket and Magnet to within ¾”

Spacers slide on Brackets & Magnets

Spacer added to Magnet

Summary of content (5 pages)

PAGE 1
InGrid Sensor Installation Instructions InGrid Sensor Kit Contents: Sensors Brackets Magnets Bracket Spacers Magnet Spacers Sensor Extensions IMPORTANT: The maximum distance between the bracket and magnet should be no more than 3/4 inch . Door frame is higher than door. To bring Bracket in alignment, slide spacer on to Magnet. Bracket on angled door frame and Magnet on door.
PAGE 2
Mount Bracket and Magnet Install the Sensor Once the Bracket and Magnet are attached to the door or window, Sensors may be installed. You will need to have the Handset with you to install the Sensor. Remove the battery tab from the Sensor Pull On the Handset 1. Attach double-sided tape to the bottom of the Magnet. 2. Attach Magnet to the door. 3. Attach double-sided tape to the bottom of the Bracket. 4. Attach the Bracket to the door frame.
PAGE 3
InGrid will then verify the Sensor is communicating with the system. “Sensor Added” will be displayed when done. o Press OK. If you continue to have trouble adding the Sensor, try the following: Move a Grid Controller: If the system again indicates that it can not find the Sensor; NOTE: If the sensor is not found or added see the Sensor Not Found or Sensor Not Added Sections. 1. Edit Sensor Name (Optional) 2. Default Sensor names are assigned in order of installation.
PAGE 4
Insufficient Space For Mounting 15” FCC Information Sensor Extension Mounting Method Mount Sensor Bracket, Sensor Extension and Magnet 1. Remove the protective seal to expose the adhesive from the double-sided tape. 2. Adhere to the bottom of the magnet and sensor extension. 3. Mount the sensor extension to the selected location on the door frame and the magnet to the selected location on the door. 4. Remove the protective seal to expose the adhesive from the double-sided tape. 5.
PAGE 5
Warranty One Year Limited Warranty For Consumer Products and Accessories purchased in the United States and Canada. What this Warranty Covers Subject to the exclusions contained below, InGrid, Inc. warrants its products (“Products”) and InGrid-branded or certified accessories sold for use with these Products (“Accessories”) to be free from defects in materials and workmanship under normal consumer usage for a period of one (1) year as outlined below.