User's Manual

ManualsBrandsLifeShield ManualsElectronicsWireless Security System Keypad

Base Installation Instructions

Model BSC1000

Replacement Base

When your replacement Base was shipped

to you, your account was de-activated and

an e-mail was sent to the contact address

we have on file for you. That e-mail

contained a new User Name and Activation

Code. You will need that information to re-

activate your system after you have installed

your new Base and re-installed your system

components. If you do not have your User

Name and Activation Code, contact InGrid

Customer Service at 1-877-INGRID7or on-

line at

www.InGridHome.com.

Use the original User Guide and Installation

Poster if you need more detailed information

on how to install system components.

Install the Base

Perform the following steps to install the

base:

1. Connect Battery Pack

The Base is shipped with the battery pack

installed, but not connected. The following

steps outline how to connect and install the

battery pack.

a. Open the battery compartment and

remove the battery

b. Locate the two pin jack inside the

battery compartment.

c. Insert the battery plug into the jack, and

insert the battery.

d. Replace the battery cover.

2. Connect Power Supply

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN

INCORRECT TYPE. DISPOSE OF USED BATTERIES

ACCORDING TO THE INSTRUCTIONS.

Note:

1) Use only InGrid IG180 rechargeable battery packs

supplied with your various Home Protection

components.

2) Replacement battery packs are also available

through the InGrid’s customer service at 1-877-

INGRID7 or on-line at www.InGridHome.com.

3) Use only the supplied electrical power adapter. Do

not use any other adapter.

4) Place the power cord so that it does not create a

trip hazard or where it could become pinched and

create an electrical hazard.

5) Do NOT use electrical power outlets that are

controlled by a wall switch

Connect the Base to the Internet and

Telephone Line (optional)

When Using a Cable Modem

a. Connect the Ethernet cable (provided in

your original kit) to an Ethernet port on

your router and the Ethernet port on the

back of the Base.

b. Optional Telephone Connection – InGrid

recommends that the Base be

connected to a telephone jack to provide

back up communications. Use the

telephone cable provided in your original

kit.

Base

Cable Modem

Ethernet

Cable

Phone

Cord

Ethernet

Cable

Wall Jack

Phone

Wall Jack

When Using a DSL Modem

Battery Pack

Base

Power Cord

Battery

Connector

a. Connect a phone splitter to the phone

wall jack. Connect the phone cord

provided in your kit to the splitter and

jack on the back of the base. Connect

the DSL phone cord to the other splitter

jack.

b. Connect the Ethernet cable provided in

the kit to an available Ethernet port on

the router and the port on the back of

the base.

Summary of content (6 pages)

PAGE 1
Base Installation Instructions Model BSC1000 CAUTION Replacement Base When your replacement Base was shipped to you, your account was de-activated and an e-mail was sent to the contact address we have on file for you. That e-mail contained a new User Name and Activation Code. You will need that information to reactivate your system after you have installed your new Base and re-installed your system components.
PAGE 2
Within 5 seconds of replacing the battery, Press the * and # keys at the same time Display should show “not registered” o Return the Handset to the Charger o E thernet C able B ase E thernet C able P hone C ord P hone C ord P hone W all Jack Note: 1. If you are installing a router for the first time, refer to your router installation instructions for connecting. 2. InGrid recommends connecting the phone line to all kit devices. 3.
PAGE 3
should feel a click. The sensor is now reset to factory default settings. Re-register Grid Extenders You need to have a Handset that is registered on the system to re-register Grid Extenders.
PAGE 4
Users. They do not have to be returned to factory default settings. Follow these steps to assign Users to Key Chain Remotes: 1. Press Menu and Select Setup/Security/Key Chains/ 2. You will be asked to wait 5 seconds and then will be instructed to press all 4 keys on your keychain. 3. You will be informed that the Keychain has been found and added and asked to confirm. Press OK to add. 4. You will then be asked to assign the keychain to a user. The system provides a list of the Users on your system.
PAGE 5
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.
PAGE 6
Warranty One Year Limited Warranty For Consumer Products and Accessories purchased in the United States and Canada. What this Warranty Covers Subject to the exclusions contained below, InGrid, Inc. warrants its products (“Products”) and InGrid-branded or certified accessories sold for use with these Products (“Accessories”) to be free from defects in materials and workmanship under normal consumer usage for a period of one (1) year as outlined below.