User Manual

ManualsBrandsLifeShield ManualsElectronicsBK410 Keypad

Brinks Keypad 1

InGrid Home Protection System

Brinks Keypad

Model BK410

Installation Instructions

June 2005

PRELIMINARY

PRODUCT DESCRIPTION

The Brinks Keypad is an InGrid Grid Controller that can operate alone or with other Grid Controllers to create a

security system for monitoring a residential home or small office. The Keypad receives radio signals from other

Grid Controllers and from wireless Sensors. One or more Keypads can be registered in a single InGrid system.

Each Keypad contains a Liquid Crystal Display (LCD) and a piezo siren that each provide a variety of user feedback.

When operated as a local only system, the Keypad will emit a loud siren if an alarm condition occurs. When

operated in conjunction with an alarm monitoring service, the Keypad may communicate with another Grid

Controller such as a Signal Extender which is then used to provide a communications link to a central monitoring

station. The Keypad is a supervised device that is regular communications with other Grid Controllers.

INSTALLATION

This section describes guidelines for installing, programming, mounting, and testing the Keypad.

¾ Installation Guidelines

• The Keypad will typically communicate at a range of up to 500 feet from other Grid Controllers.

• Do NOT use an outlet that is controlled by a switch.

¾ Mounting

Note: You must be free of static electricity before handling the Keypad. Touch a bare metal surface or wear a

grounding strap to discharge yourself.

1) Select a location on a convenient and accessible wall.

2) Remove back cover using screwdriver. If present, the battery must be first removed. The front of the Keypad

contains static sensitive printed circuit boards. Set the front of the Keypad on the static protected packing

material until needed for the mounting steps below.

Summary of content (10 pages)

PAGE 1
InGrid Home Protection System Brinks Keypad Model BK410 Installation Instructions June 2005 PRELIMINARY PRODUCT DESCRIPTION The Brinks Keypad is an InGrid Grid Controller that can operate alone or with other Grid Controllers to create a security system for monitoring a residential home or small office. The Keypad receives radio signals from other Grid Controllers and from wireless Sensors. One or more Keypads can be registered in a single InGrid system.
PAGE 2
3) Mount at height convenient for use, typically 55 to 60 inches above the floor. A wire must be run from the Keypad to the Power Supply, so choose the location wisely to minimize the difficulty of running the wire. The Keypad is designed to be mounted on drywall or wood. Mounting on metal studs, or any type of brick, stone, or concrete block will likely reduce the wireless range of the Keypad.
PAGE 3
¾ Programming The Keypad is used only with the alarm monitoring service provided by Brinks Home Security. An InGrid Home Protection System monitored by Brinks requires special programming that sets many parameters to be compatible with the Brinks central monitoring station. These parameters may only be loaded by a Brinks installer using an InGrid Programmer. OPERATING THE SYSTEM ¾ User Codes When the system is installed, you select a code number to turn the system on and off.
PAGE 4
Turning the System On with Motions Turned Off / Instant Mode 1) 2) 3) 4) Close all of the doors and windows and make sure that the message window displays READY. Press the ON key. Press the MOTION OFF key. Press the INSTANT key. The ON light turns on. The Keypad displays ON, MOTION OFF, and INSTANT. Do not leave the building or open any protected windows without first turning the system off.
PAGE 5
1) Enter the building through a designated entry door. The Keypad’s message window displays ALARM. The siren is sounding and the ON light is lit. 2) Enter your user code. The Keypad beeps. Wait for Brink’s to call. Be prepared to give the Brink’s operator your code word. Do not use the telephone if you intend to cancel the alarm. If your telephone line is busy, Brink’s may dispatch emergency personnel to your home, which could result in a false alarm fine.
PAGE 6
How to View Alarm Memory You can use alarm memory to determine which zones were in alarm. 1) Press the OPTIONS key until the message window displays: ALARM MEMORY, ENTER CODE. 2) Enter your user code. The Keypad beeps. The message window shows which zones were in alarm. How to Delete an Auxiliary Code If you wish to delete an auxiliary user code, do the following: 1) Press the OPTIONS key until the message window displays: AUXILIARY CODES, ENTER MASTER CODE. 2) Enter the master user code. The Keypad beeps.
PAGE 7
3) 4) 5) 6) Enter your code. The message window displays READY DOOR CHIME Open each protected door and window, listen for the Keypad and Signal Extender to beep. If you do not hear the Keypad beep, note the zone number and call Customer Care at 1-800-445-0872. When you have finished testing, end the test by repeating steps 2 and 3. Testing With Not Ready Zones If the system is not ready to test, the message window displays NOT READY.
PAGE 8
2) If you have power to your home, check the power supply to ensure that it is properly plugged in. If this solves the problem, stop. Otherwise, continue to the next step. 3) Unplug the power supply. It may be screwed in place; if so, remove the screw. Plug a small appliance into the outlet to verify the outlet is working properly. If it is, continue to the next step. 4) Look for a ground-fault circuit interrupter (GFCI) on the outlet, or on a nearby outlet.
PAGE 9
What to do: 1) To silence the Keypad’s beeping, press the CANCEL key. 2) Wait 30 minutes for the system to reset. 3) If the detector has not reset after 30 minutes, the trouble message returns and the Keypad beeps. Component Failure One of the system’s devices is not operating properly Call Brink’s Indication If you receive this trouble message, call Brink’s Customer Care at 1-800-445-0872 for assistance. SPECIFICATIONS Compatibility:........................................
PAGE 10
www.ingridhome.