User Guide Model：LS5BVD-N11S Rev: 2.
LS5B User Guide Libre Wireless Technologies Private Limited librewireless.com Copyright © 2016 Libre Wireless Technologies. All rights reserved. Circuit diagrams and other information relating to Libre Wireless Technologies products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given.
LS5B User Guide Table of Contents 1. Introduction ................................................................................................................................. 8 1.1. 2. User Guide Insight ............................................................................................................................. 8 Libre Wireless Technologies’ EVK ........................................................................................ 9 2.1. 3. LS5B EVK Setup ......................
LS5B User Guide 6.3.1. WPS Trigger from Command Line ....................................................................................... 41 6.3.2. WPS Trigger from LUCI ............................................................................................................ 41 6.3.3. WPS Trigger from Key Button ............................................................................................... 42 6.4. I-Device Wi-Fi Settings Sharing ................................................
LS5B User Guide 7.21. Zone Volume. .................................................................................................................................... 60 7.22. Music Services .................................................................................................................................. 61 7.22.1. vTuner ............................................................................................................................................ 61 7.22.2. TuneIn........
LS5B User Guide Table of Figures Figure 2-1: LS5B EVK (2.0) Peripherals ........................................................................................ 9 Figure 2-2: LS5B EVK (3.0) Peripherals ...................................................................................... 10 Figure 3.2.1-1: Firmware Upgrade Method Selection ............................................................ 13 Figure 3.2.1-2: Firmware Update Webpage .................................................................
LS5B User Guide Figure 7.9-1: Miracast Enabled Speaker ..................................................................................... 52 Figure 7.16-1: Device Name Section ............................................................................................. 57 Figure 7.17.1-1: Switch to Wired Mode ....................................................................................... 58 Figure 7.17.2-1: Switch to Wi-Fi Mode ....................................................................
LS5B User Guide 1. Introduction Libre Wireless provides evaluation kits (EVK) for users to gain familiarity with our products and expedite their own design and development. User can connect to LS5B module through RS232 UART, SD card, USB, or wireless interface to configure the module, manage the on board device on the module, and perform functional test. 1.1.
LS5B User Guide 2. Libre Wireless Technologies’ EVK Figure 2-1: LS5B EVK (2.0) Peripherals Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Figure 2-2: LS5B EVK (3.0) Peripherals 2.1. LS5B EVK Setup To setup the LS5B EVK and get started proceed as below Step 1. Ensure the LS5B module is inserted in the EVK Step 2. Connect the USB-to-Serial Cable from Serial port of EVK to USB port of Laptop Step 3. Connect the Power adaptor to DC Jack on EVK Step 4. Power On the EVK, using ON/ OFF Switch Step 5. Open the terminal tool (Hyper Terminal / Teraterm) on your laptop Step 6.
LS5B User Guide 3. Firmware Update The Firmware Update process, facilitates update of U-Boot, BSL, and Application images individually, or all of them together (Single-Image) to the LS-Module.
LS5B User Guide 3.1. Single-Image Update and Application Update Single-Image binary file named, “lsimage” is released to customers on Libre Portal. The “lsimage” contains U-Boot, Factory-ENV, BSL, and Application. For detail on using the Single-Image tool refer to LibreWireless-TechNote_Software_Customization_Kit available on Libre Portal. Application Update The Application-Image used to update the firmware is a binary file.
LS5B User Guide Steps Step 1. Execute command #netcfg in the device terminal to know the device IP For Example, 10.0.1.13 Step 2. Enter the IP in the address bar of your browser. For Example, 10.0.1.13 Step 3. In the Firmware upgrade section, Select Method as Network and Click Upgrade Figure 3.2.1-1: Firmware Upgrade Method Selection Step 4. Click Choose File to select the binary file for upgradation and Click Update to upgrade the firmware.
LS5B User Guide Figure 3.2.1-2: Firmware Update Webpage Step 5. LS5B Shows below shown confirmation page. User has to click on OK button on the page. Figure 3.2.1-3: Firmware Update Confirmation webpage Step 6. LS5B-Module reboots to BSL, Firmware Update progress page is displayed. Figure 3.2.1-4: Firmware Update Progress Page On successful upload, web page displays the status of the update process Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Figure 3.2.1-5: Firmware Update Status End-- 3.1.2. SD-Card / USB Method To update the binary file (Application-Image or Single-Image) on the LS5B module from SDCard / USB using the web server proceed as below Steps Step 1. Ensure the binary filename as “lsimage” and place the firmware image in root directory of SD-Card / USB. The Firmware image should not contain any extension. Step 2. Insert the SD-Card / USB in the LS5B EVK Step 3.
LS5B User Guide Figure 3.2.2-1: Firmware Upgrade Method Selection Step 6. LS5B-Module reboots to BSL, and Firmware Upgrade from SD-Card / USB starts automatically. On successful upgrade, LS5B-Module reboots, with the updated application. End - - 3.1.3. Internet Method To update the Application Image on to the LSx module proceed as below. Make sure the LS5B module is in Home-Network mode, and is connected to the Home-AP with internet access.
LS5B User Guide Firmware Download XML NV-Item fwdownload_xml is used to provide the URL for the XML file that contains the information about Firmware version, HOST-MCU version and the link to download the firmware. Use the syntax below to provide the URL for firmware update. To Provide the URL for Firmware Update over Internet #setenv fwdownload_xml http://10.0.1.14/share/firmware/LS5B/firmware_download.xml Firmware Download XML Structure Firmware Download XML file includes the following tags.
LS5B User Guide Steps Step 1. Place the Firmware (Combined image with LS-Image, and HOST-MCU Image) in the URL provided. Step 2. Update the NV-Item fwdownload_xml with the URL of the XML file. Step 3. Execute command #netcfg in the device terminal to know the device IP Step 4. Enter the IP in the address bar of your browser Step 5. In the Firmware upgrade section, Select Method as Internet and Click Upgrade Step 6. LS5B-Module reboots to BSL.
LS5B User Guide Step 7. On Successful download, Firmware Upgrade starts and the progress status is displayed. Step 8. Module reboots on successful completion of upgrade process. 3.2. BSL Update The BSL is a one type of boot loader that facilitates upgrade of Application Image on to the LSx module. Below section describes procedure to program the BSL on to LSx Module. Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide 3.2.1. TFTP Method To update the BSL for LS5B module using TFTP proceed as below Step 1. Install TFTP server in Win 7 laptop / PC You can download the TFTP server from web Step 2. Store Image.bin file, in the same folder as TFTP is placed Disable the firewall in windows laptop / PC. Firewall will block the file from being loaded. Step 3. Connect the PC and module with Ethernet cable Step 4. Set Static IP 10.10.10.
LS5B User Guide Figure 3.3.1-1: BSL Update Terminal Warning Message Prompt Step 11. To set default Server and Device IP address, Press Enter key on Keyboard Figure 3.3.1-2: BSL Default IP Address Step 12. Provide the name of the binary for BSL, to be flashed on the U-Boot prompt. For Example, Image.bin Make Sure the Binary name provided, is as in the repository. Wrong binary name might make the module unusable. Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide End-- 3.3. U-Boot Update 3.3.1. TFTP Method To update the U-Boot for LS5B module using TFTP proceed as below Step 1. Install TFTP server in Win 7 laptop / PC You can download the TFTP server from web Step 2. Store Image.bin file, in the same folder as TFTP is placed Disable the firewall in windows laptop / PC. Firewall will block the file from being loaded. Step 3. Connect the PC and module with Ethernet cable Step 4. Set Static IP 10.10.10.
LS5B User Guide Figure 3.4.1-1: U-Boot Update Terminal Warning Message Prompt Step 11. To set default Server and Device IP addres, Press Enter Key on Keyboard Figure 3.4.1-2: U-Boot Default IP address Step 12. Provide the name of the binary for U-Boot, to be flashed on the U-boot prompt For Example, Image.bin Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Make Sure the Binary name provided, is as in the repository. Wrong binary name might make the module unusable. End-- Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide 4. Configuring Non-Volatile-Item The latest LS-Images (vB5004 and onwards) supports NV-Item from application only and is accessible from Application Shell prompt. NV-item in U-Boot is not supported anymore. To configure all the NV-Item values at one shot as per customer choice, customers can use the envitem.xml file. This xml file is used to generate a final Golden-Image for production.
LS5B User Guide Command Syntax #SetFacDefault To know all the NV-items values, type the below command in the command line. Command Syntax #GetAllENV To configure NV-item hostpresent Example To Know the value of the NV-Item hostpresent. #setenv hostpresent 1 #reboot #getenv hostpresent For detailed information on Configuring the NV-Items refer to “LibreWirelessTechNote – Non-Volatile_Items_in_LibreSync” available in Libre Portal. Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide 5. Key Button Functionality 5.1. Setup Button (WAC / SAC / DDMS) The Setup (SW5) button in LS-EVK is configured to trigger WAC / SAC after the LS module boots up as below. Press and Hold the setup button on the LS EVK for 3 seconds, to come out of the DDMS mode. - LS EVK connects to the AP or the SSID configured earlier. - To connect the LS EVK to different AP or SSID, Press and Hold the setup button on the LS EVK for 3 seconds again, to trigger SAC / WAC.
LS5B User Guide 6. Network Configuration The network configuration method supported in LS-Module is Wireless Network Setup Using WAC Method Wireless Network Setup Using SAC Method Wireless Network Setup Using Webserver Method Wireless Network Setup Using WPS Push Button Method 6.1. Wireless Network Setup Using WAC and SAC 6.1.1. Wireless Network Setup Using WAC To setup a wireless network using Wireless Area Controller (WAC) proceed as below Step 1.
LS5B User Guide iOS device shares its Wi-Fi settings; that is SSID and Password with the WAC speaker and configures the device. On successful configuration the device is configured to the Wi-Fi network to which the iOS device is connected. End-- 6.1.2. Wireless Network Setup Using SAC (Speaker Android Configuration) Method To setup a wireless network using Libre Android APP proceed as below Step 1. Power on the Speaker (DUT) and press and hold the Setup button on LS5B EVK for 3 seconds.
LS5B User Guide Step 3. Tap Configure in the menu Step 4. In Speakers To be Setup section Tap Add more Speaker. Step 5. In Speaker Setup page, Tap configure using SAC. Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Step 6. On Speaker Setup page, Tap Next Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Step 7. On Speaker To Be Setup page select the speaker to be configured. Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Step 8. On Speaker Setup page, select the Home-Network and enter the password. Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Step 9. Tap SAVE. Step 10. Continue the configuration steps for all the speakers. End-- 6.1.3. WAC / SAC Trigger Behaviour in DDMS Mode and Non-DDMS Mode This sections explains different behaviours of the speaker for network configuration when WAC / SAC is triggered. For details on the network configuration using WAC / SAC refer Section 6.1 and Section 6.2. Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Scenario 1 Precondition LS-Enabled speaker is not connected to AP. Action WAC / SAC is triggered using the Setup Button (Press and Hold for three seconds) in LS EVK or through Message-Box 142. Result LS-Enabled Speaker enters WAC / SAC mode for Network Configuration. Scenario 2 Precondition LS-Enabled speaker is connected to AP. Action WAC / SAC is triggered using the Setup Button (Press and Hold for three seconds) in LS EVK or through Message-Box 142.
LS5B User Guide Scenario 4 Precondition LS-Enabled speaker is connected to AP. Action 1. Reboot the Speaker. 2. Configure the speakers to DDMS SA-Mode (refer to DDMS usability guide). 3. Trigger WAC / SAC using the Setup Button (Press and Hold for three seconds) in LS EVK or through Message-Box 142. Result LS-Enabled Speaker switches from DDMS Mode and connects to the AP configured earlier. Scenario 5 Precondition LS-Enabled speaker is in DDMS SA-Mode and was not connected to AP earlier. Action 1.
LS5B User Guide Scenario 7 Precondition LS-Enabled speaker is in DDMS HN-Mode and was connected to AP earlier. Action 1. Reboot the Speaker and 2. Trigger WAC / SAC using the Setup Button (Press and Hold for three seconds) in LS EVK or through Message-Box 142. Result LS-Enabled Speaker switches from DDMS HN-Mode and enters WAC / SAC mode for Network Configuration. 6.2. Wireless Network Setup Using Webserver 6.2.1. Webpage Method This method is used if the device is already connected to a network.
LS5B User Guide Step 3. In Select Your Network section, Select the Access Point (AP) to be connected, from Select your Network drop-down list and Click Save Device reboots and connects to the new network and acquires new IP Figure 6.2.1-2: Network Configuration End -You can also connect the device to the network of your choice by setting the Static IP for the device. Static IP address is a known IP address pre-allocated to the device. Static IP does not change and the device will have the same IP always.
LS5B User Guide Figure 6.2.1-3: Network Configuration using Static IP Use any IP address from the Access Point IP’s address range which is not assigned to any client device already. Device reboots and connects to the network and acquires the static IP as defined. Step 4. To know the IP address of the device, execute command #netcfg in the device terminal End-- 6.2.2. LS-Configure Method To setup wireless network using LS-Connect proceed as below Step 1.
LS5B User Guide Step 3. Enter the following URL in the address bar of your browser 192.168.43.1 webpage shows Network status as shown in Figure 6-4. Figure 6.2.2-1: Network Status in Webpage Step 4. Select the Access Point (AP) to be connected to from Select Your Network drop-down list Step 5. Select Security Type from Security drop-down list, Enter the valid login credentials and Click OK Device disconnects from laptop and connects to the network selected Step 6.
LS5B User Guide Figure 6.2.3-1: Configure Network Manually End-- 6.3. Wireless Network Setup Using WPS Push-Button Method 6.3.1. WPS Trigger from Command Line To setup a wireless network using WPS proceed as below Step 1. On system boot, enter the command #wpa_cli wps_pbc in device terminal Step 2. Trigger (Press Once) Setup button in the Access Point. Device connects to the Network of the Access Point. Step 3. To know the newly acquired IP execute command #netcfg in the device terminal End-- 6.3.2.
LS5B User Guide For more information see section 6 in LUCI Technical Note, LibreWirelessTechNote - LS_Light_Weight_Universal_Control_Interface. 6.3.3. WPS Trigger from Key Button (TBG) 6.4. I-Device Wi-Fi Settings Sharing Host-MCU requests the LS enabled device to share the Wi-Fi settings over Message-Box # 126. On request from HOST-MCU, iOS device shows a pop-up message to the user to “Ignore” or “Allow” the settings sharing. Figure 6.4.
LS5B User Guide Or Check the IP address from the webpage of the Home-AP IP address from the Webpage of Home-AP To know the IP address of the LS-Module from Home-AP webpage do as below. Step 1. Enter the default IP address of your Home-AP in the address bar of your browser. For example, if you use D-link router then the Default IP is 192.168.0.1 Step 2. Enter the Login Credentials and login to the webpage of Home-AP Step 3. Go to Advanced Options and go to Wireless section Step 4.
LS5B User Guide 7. Features 7.1. Libre APP for Android LUCI enables user to remotely, control the LibreSync LS5B enabled product using the Libre Application for android. The application can be used to browse DLNA-DMS in the network, SD Card connected to device and other online radio stations such as vTuner and TuneIn , and stream music using the DMP feature supported by LS5B. For more information on using Libre APP refer LibreWireless-Usability_Guide_Dynamic_Direct_Multi-Node_Streaming 7.2.
LS5B User Guide Ls-Enabled device reboots, every time when it is switched from HN-Mode to SA-Mode and vice-versa For information on setting up devices for DDMS, and Using Libre App refer to LibreWireless-Usability_Guide_Dynamic_Direct_Multi-Node_Streaming The device webpage provides interface to update DDMS SSID and password. Figure 7.2-1: DDMS Setup in webpage 7.3. Software Security LibreSync software is secured using Crypto IC. Crypto IC is embedded either in the LS5B module or the ACP.
LS5B User Guide 7.5. Failsafe Mechanism Failsafe Mechanism safeguards the modules from being corrupted or unusable, in case of power failure or reset during the firmware upgrade. For more information on Failsafe Mechanism see LibreWirelessTechNote_FailsafeFirmware_Upgrade, available in Libre Portal. 7.6. Autosense of Audio CODEC The new LS Firmware will automatically detect the presence of Audio CODEC in the firmware.
LS5B User Guide Step 3. Select the device and select Play AirPlay starts streaming Figure 7.7-1: AirPlay Stream End-- 7.8.1. Password for Airplay Playback You can either enable or disable a password, to start Airplay playback on the LS enabled device through a webpage. Enable To enable a password for Airplay Playback proceed as below. Step 1. Execute command #netcfg in the device terminal to know the device IP For Example, 10.0.1.13 Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Step 2. Enter the IP in the address bar of your browser with port number For Example, 10.0.1.13 Step 1. In Your Device Name section, Enter the Airplay Password in the white box below and Click Apply Device reboots automatically. Figure 7.7.1-1: Password for Airplay Step 2. Open the Control Centre or Music App on iOS device Or Use iTunes installed on any machine Step 3. Tap the AirPlay icon AirPlay enabled LibreSync device is listed Step 4. Select the device and Select Play Step 5.
LS5B User Guide Figure 7.7.1-2: Enter Password for Streaming End-- Disable To disable a password for Airplay Playback proceed as below. Step 6. Execute command #netcfg in the device terminal to know the device IP For Example, 10.0.1.13 Step 7. Enter the IP in the address bar of your browser with port number For Example, 10.0.1.13 Step 8. In Your Device Name section, Clear the previous Password and leave the white space blank and Click Apply Step 9.
LS5B User Guide Figure 7.7.1-3: Disable Airplay Password Device reboots automatically. End -- 7.9. DLNA ® / DMR After the device is configured to the network, device is discoverable over UPnP®. Any Universal Plug and Play (UPnP) / Digital Living Network Alliance (DLNA) certified controller can be used to stream music to the device. To test Play To functionality proceed as below Step 1. Open Media Player on Windows 7 Step 2.
LS5B User Guide Figure 7.8-1: Media Player Stream Menu Figure 7.8-2: Media Streaming Options Digital Media Renderer (DMR) functionality can be verified using any app on the Android / iOS devices as well. For example, the native audio player on Samsung Galaxy devices can be used. End-- 7.10. Miracast Miracast also known as Wi-Fi display, is the feature used to mirror the mobile (video and audio) to the Miracast sink device. It uses wifi-P2P technology for communication.
LS5B User Guide Step 1. Send the type 2 Command in Message-Box 113 over LUCI For more information see Message 113 in file LibreWirelessTechNote LS_Light_Weight_Universal_Control_Interface Step 2. Start the local audio playback on an Miracast enabled Android Phone For Example, Nexus 5 Step 3. Go to the Miracast screen, on the Android Phone For Example, In Nexus 5 phone go to Settings > Display > Cast screen Miracast enabled speaker is listed. For example, LibreCast Figure 7.
LS5B User Guide Step 4. Tap the Speaker from the list Speaker connects to the Miracast and streams the music from the current playlist Step 5. Close the Miracast Screen End-For details on scenarios of Miracast Mode Switching with other Different Modes (WAC/DDMS), and Miracast Source Switching with other Different Sources, refer to “LibreWirelessTechNote-Miracast_Mode_and_Source_Conversion” document available in Libre Portal. 7.11. SD-Card Playback LS supports Audio Playback from SD-Card.
LS5B User Guide When Host-MCU is Present (in Customer Product) If the NV-Item hostpresent is set to '1' , To Enable NV-Item hostpresent #setenv hostpresent 1 To start playback from Apple Device following sequence is to be followed. Step 1. LS sends the new source to the Host MCU over Message-Box# 10 Step 2. Host MCU may send a command to LS (Command Type: GET) over MessageBox#50 (Current Source – with value 16 that is Apple Device) to get to know the current playback source, if any. Step 3.
LS5B User Guide You can save up-to 10 songs (URLs) of your choice as favourites in LibreSync platform. When you save the 11th favourite Song (11th URL), the oldest song saved (1st URL) is erased and replaced with the song saved earlier (2nd URL). You can save and play favourites using the Libre Reference APP (Android / iOS). To Save the current song as Favourite, Tap the Star icon in Now Playing Screen.
LS5B User Guide Toggle Between Favourites Use the Previous, and Next keys to toggle between favourites. You can also send the Play Control commands Over LUCI via Message-Box 40. 7.14. USB Playback LS supports audio playback from USB. User can select the content source from an USB drive to stream music on LS-Enabled speaker. 7.15. TCP / IP Tunneling TCP/IP Tunnelling is a unique feature supported by LS modules. Tunneling enables a Host MCU to communicate with other network devices over UART.
LS5B User Guide Step 1. Execute command #netcfg in the device terminal to know the device IP For Example, 10.0.1.13 Step 2. Enter the IP in the address bar of your browser with port number For Example, 10.0.1.13 Step 3. In Your Device Name section, Enter the Device Name in the white box and Click Apply Figure 7.16-1: Device Name Section The device name length can be up-to maximum of 50 characters.
LS5B User Guide End-- 7.18. Switch between Wired and wireless modes You can switch between wired and wireless mode using the Webserver 7.18.1. Switching to Wired Mode To switch to wired mode from Wi-Fi mode proceed as below Make Sure device is connected to an Wi-Fi Network Step 1. Execute command #netcfg in the device terminal to know the device IP For Example, 10.0.1.13 Step 2. Enter the IP in the address bar of your browser with port number For Example, 10.0.1.13 Step 3.
LS5B User Guide LS module reboots automatically End-- 7.18.2. Switching to Wireless Mode To switch to wired mode from Wi-Fi mode proceed as below Step 1. Execute command #netcfg in the device terminal to know the device IP For Example, 192.168.0.103 Step 2. Enter the IP in the address bar of your browser with port number For Example, 192.168.0.103 Step 3. In Select Your Network drop-down list, select Switch to Wi-Fi mode and Click Save Figure 7.17.
LS5B User Guide 7.19. Pair / Share credentials Pair functionality enables LS-Enabled speaker in SA-Mode to pair (join) with other LSEnabled speaker. Share functionality allows the LS-Enabled speaker to share its Wi-Fi credentials with other LS-enabled speakers. For Example: If there are two LS-Enabled speakers, called LS-Speaker A and LS-Speaker B, then LS-Speaker A with pair enabled, can join LS-Speaker B only when LS-Speaker B is enabled with share.
LS5B User Guide Zone Volume uses scaling ratios to provide a good user experience and intuitive system response based on controlling volume levels for dynamic groups of speakers - called "Sound Scenes”. Zone volume manages an overall Sound Scene’s Volume. Once speakers are adjusted, the Sound Scene Volume will raise and lower each speaker’s volume in a relative way keeping the relationship of volume level between speakers.
LS5B User Guide Figure 7.18.1-1: vTuner Browse Screen Step 4. LS enabled speaker starts streaming the song from vTuner. Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Figure 7.18.1-2: Now Playing Screen for vTuner End -- 7.22.2. TuneIn TuneIn is an internet radio station that enables streaming of music. TuneIn on Libre platform can be used to stream music using the Libre APP. To stream music from TuneIn proceed as below. Step 1. In the Now Playing screen of Libre APP, Tap Sources Step 2. Tap TuneIn from the source List Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Step 3. Browse through the list and select the song of your choice. Figure 7.18.2-1: TuneIn Browse Screen Step 4. LS enabled speaker starts streaming the song from TuneIn. Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Figure 7.18.2-2: Now Playing Screen for TuneIn Sync Your TuneIn Account Step 5. In Tunein Home-Page, Tap Settings. Step 6. Follow the steps as listed below. 1 From www.tunein.com logon with your account. 2 Go to My Info, and select Devices or tunein.com/mydevice. Step 7. Tap Registration Code Step 8. Confirm if the Registration Code information is correct. End -Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide 7.22.3. Melon Melon is an online music service, User should use the melon Player to browse through the music of choice. Melon Application generates the URL for the song selected and sends it to the LS-Speaker using LUCI over Message-Box # 41 and Command ‘2’ to SET. LS-Speaker downloads the song and renders the audio output. Melon Music service Application should Append the song URL with “MELON:” while sending the command over LUCI.
LS5B User Guide Figure 7.18.4-1: QQ Music APP Step 4. Login to QQ Music, using the Username and Password received, during registration. Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Figure 7.18.4-1: Login Screen Step 5. Browse for songs in the QQ Music Server Step 6. In Now playing screen, select ‘Q’ symbol Figure 7.18.4-2: Device Selection Option Step 7. Select the LS enabled device Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Figure 7.18.4-3: Device List Playback from QQ music on the LS enabled device starts. End - - 7.22.5. Spotify LibreSync enables you to stream music via Spotify connect. Spotify on LS-Enabled speakers supports to Save / Play/ Delete presets, for more information on Spotify Preset Actions refer to Message-Box # 75 in LUCI Document (LibreWirelessTechNote-LS_Light_Weight_Universal_Control_Interface) available in LibreSync Document Portal. To use the Spotify connect APP proceed as below.
LS5B User Guide Step 2. Download the Spotify app from the App store/Play Store. The device name is listed as, LibreSync_xxxxxx In Spotify free account, LS Device will not be listed in the Spotify speaker list. To stream music from Spotify connect proceed as below. Step 1. Reboot the LS enabled device and connect to the network. Step 2. Connect iOS device/Android phone to the same network. Step 3. Open the Spotify APP Figure 7.18.5-1: Spotify APP Step 4.
LS5B User Guide Figure 7.18.5-1: Spotify Login Screen Step 5. Browse for songs in the Spotify Server Step 6. In Now playing screen, select Speaker symbol in right bottom Figure 7.18.5-2: Device Selection Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Step 7. Select the LS enabled device Figure 7.18.5-3: Device List LS enabled device starts streaming music from Spotify Connect End -- 7.22.6. Deezer Deezer on Libre platform can be used to stream music using the Libre APP. To stream music from Deezer proceed as below. Step 1. In the Now Playing screen of Libre APP, Tap Sources Step 2. Tap Deezer from the source List Step 3. Enter the User Name and Password to login to the music service.
LS5B User Guide Step 4. Browse through the list and select the song of your choice. Figure 7.18.6-1: Deezer Browse Screen Step 5. LS enabled speaker starts streaming the song from Deezer. Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Figure 7.18.6-2: Now Playing Screen for Deezer End -- 7.22.7. Tidal Tidal, also known as TIDALHiFi is a subscription-based music streaming service that offers lossless audio and high definition music. The service has over 30 million tracks and 75,000 music videos. Tidal on Libre platform is used to stream music using the Libre APP. To stream music from Tidal proceed as below. Step 1. In the Now Playing screen of Libre APP, Tap Sources Step 2. Tap Tidal from the source List Step 3.
LS5B User Guide Step 4. Browse through the list and select the song of your choice. Figure 7.18.7-1: Tidal Browse Screen Step 5. LS enabled speaker starts streaming the song from Tidal. Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide Figure 7.18.7-2: Now Playing Screen for Tidal End -- Favorites in TIDAL You can save a play-list as favorite, or an entire album, or an artist as favorite in the browse view of TIDAL. For the play-list / album / artist of your favorite, Just tap the Libre Wireless Technologies User Guide: LS5B, Ver. 2.9 Libre Confidential icon against it.
LS5B User Guide 7.23. Telnet Telnet provides access to the command line interface of the LS-Enabled device over Ethernet / Wi-Fi. To enable or disable Telnet in the device LibreSync provides a configurable Non-Volatile Item “telnet”. Setting this NV-Item as 1 enables Telnet in the device. For more information on configuring NV-item refer to LibreWirelessTechNote NonVolatile_Items_in_LibreSync available in Libre Portal. Libre Wireless Technologies User Guide: LS5B, Ver. 2.
LS5B User Guide 7.24. Dynamic Output Sampling Frequency Dynamic Output Sampling Frequency enables the output sample rate of the speaker to be changed according to the audio track sample rate. To enable this feature, the NV-item to be used is outputfs (Refer NV-item document available in Libre Portal). The sample rates to be supported should be mentioned in the NV-item value.
FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
