Waspmote Product information Libelium Comunicaciones Distribuidas S.L. María de Luna 11, Instalaciones CEEIARAGON, Nave 5 C.P: 50018, Zaragoza Tel: +34 976 54 74 92 FAX: +34 976 73 37 19 info@libelium.com http://www.libelium.
Waspmote product information - Confidential Document - CONTROL DE VERSIONES DEL DOCUMENTO Fecha Autor 04/09/21 Marcos Yarza 22/04/2009 David Gascón 23/04/2009 Marcos Yarza 30/05/2014 Javier Solobera Modificaciones Schematic was deleted María de Luna 11, nave 5 instalaciones CEEI. 50018 Zaragoza. Tel 976547492. http://www.libelium.
Waspmote product information - Confidential Document - Documento Confidencial DOCUMENTACIÓN CONFIDENCIAL Este documento contiene documentación confidencial y queda expresamente prohibida su divulgación, copia o distribución a terceros sin la autorización expresa de Libelium. Si ha recibido este mensaje por error, se ruega lo notifique a Libelium enviando un mensaje al remitente o al correo electrónico info@libelium.com y proceda inmediatamente al borrado del mensaje original y de todas sus copias.
Waspmote product information - Confidential Document - ÍNDICE DE CONTENIDO 1 Product information...................................................................................................................... 5 1.1 General project information.......................................................................................................5 1.2 WASPMOTE MODELS.............................................................................................................. 7 1.3 WASPMOTE antennas...
Waspmote product information - Confidential Document - 1 PRODUCT INFORMATION 1.1 GENERAL PROJECT INFORMATION Waspmote is a wireless sensor mote developed by Libelium. Waspmote is a board with radio modules and others componentes such as GPS integrated. Waspmote works this way: 1º- Read the data from the sensors attached (if any) 2º- Send the information using the 2.
Waspmote product information - Confidential Document - Large Data Storage: Each mote can store up to GB's of data due to the SD flash memory it takes. The information is stored as files, as it would be done in a common computer. Ready for Emergency Events: Waspmote has an accelerometer which can wake the mote up when an event happens. Some of this events are: a fall, a crash, a linear movement. (We can detect also is someone is stealing the device).
Waspmote product information - Confidential Document - of the embedded bootloader. The bootloader software allows reprogramming the firmware directly over the USB port when unplugging the protection jumper and is casted into only a 4KB memory space. The configuration of the mote is stored inside the processor’s EEPROM avoiding any risks to lose relevant configuration variables when rebooting the mote. 1.
Waspmote product information - Confidential Document - – Switch the WASP OFF. – Unplug the battery and the USB cable. – Now you can take the modules out and plug them in again. See pictures below. María de Luna 11, nave 5 instalaciones CEEI. 50018 Zaragoza. Tel 976547492. http://www.libelium.
Waspmote product information - Confidential Document - 1.5 SIMPLIFIED OPERATING INSTRUCTIONS TO TEST THE BOARD IMPORTANT: Read ALL the operating instructions before using Wasp. Powering Wasp The WASP can be powered from different sources: USB, and battery are the most common ones. The board doesn’t include any connectors that would make possible power it from the mains or from a standard AC-DC converter. On the board there is a battery charge monitor.
Waspmote product information - Confidential Document - 2 – Open a serial port terminal Set the serial port to 9600 baud, no parity, 8 data bits, 1 stop bit and no flow control. Set the right port to communicate with the device (COM0/COM1/.. in windows, ttyUSB0/ttyUSB1/... in linux). In Windows you can use Hyperterminal. In Linux you can use: gtkterm or cutecom. 3 – Reset WASP Reset WASP pressing the reset button on the board and WASP will show the ABOUT message on the terminal screen.
Waspmote product information - Confidential Document - Now you can plug the battery and test the device wherever. To plug the battery: We are going to use a 3.7V battery plugged directly to the board on its battery connector. With the switch at its OFF position, plug in the battery connecting the power cable from it (colored red) to the positive connector (+) and the ground cable (colored black) to the negative connector (-). BE CAREFUL SINCE CONNECTING THE WIRES WRONG MAY DAMAGE THE WASP.
Waspmote product information - Confidential Document - 1.6 ELECTRICAL RATING OF THE PRODUCT The main power supply for WASP is a Li-Ion battery (3.7V – 1130 mAh). The battery can be charged with a standard mini USB connection or with a solar panel (6V – 12V). Wasp includes the circuitry necessary for the battery charge control. María de Luna 11, nave 5 instalaciones CEEI. 50018 Zaragoza. Tel 976547492. http://www.libelium.
Waspmote product information - Confidential Document - 1.7 SYSTEM CONFIGURATION María de Luna 11, nave 5 instalaciones CEEI. 50018 Zaragoza. Tel 976547492. http://www.libelium.
Waspmote product information - Confidential Document - 1.8 WORST CASE CONSUPTION The worst case is the mode where the 2.4GHz 100mW XBee module and the GSM/GPRS are both on (case E). See test modes above. It is about 200mA. María de Luna 11, nave 5 instalaciones CEEI. 50018 Zaragoza. Tel 976547492. http://www.libelium.
Waspmote product information - Confidential Document - 2 ADDITIONAL REQUIREMENTS NECESSARY FOR ALL EMC EVALUATIONS 2.1 LIST OF CLOCK FREQUENCIES The microcontroller in WASP is operating in a frequency of 8 MHz and the RTC module is operating in a frequency of 32.768 kHz. 3 ADDITIONAL REQUIREMENTS NECESSARY FOR ALL PRODUCT SAFETY EVALUATIONS 3.1 MANUFACTURING LOCATIONS Waspmote has been manufactured in Zaragoza (Spain). María de Luna 11, nave 5 instalaciones CEEI. 50018 Zaragoza. Tel 976547492.
Waspmote product information - Confidential Document - 3.2 PRODUCT MARKINGS See documentation attached to find the FCC documents of all the modules used in Waspmote. 3.3 INTERNAL BATTERIES WASP uses two different batteries for powering. – The main battery is a Li – Ion battery, voltage = 3.7V, capacity is 1130 mAh – The second battery is a Lithium Coin Battery (1620 size), voltage = 3V, capacity = 75 mAh María de Luna 11, nave 5 instalaciones CEEI. 50018 Zaragoza. Tel 976547492. http://www.
Waspmote product information - Confidential Document - 4 CERTIFICATIONS 4.
Waspmote product information - Confidential Document - 4.
Waspmote product information - Confidential Document - 4.3 ANTENNAS Waspmote: XKMWASP01 8472AWASP01 RF exposure limits are met for the antenna gain combinations listed below: If the GPRS antenna gain is 0dBi the 2.4GHz antenna is valid for values below 16dBi. If the GPRS antenna gain is 2.5dBi the 2.4GHz antenna is valid for values below 16dBi. If the 2.4GHz antenna gain is 2.2dBi the GPRS antenna is valid for values below 8dBi. If the 2.
