MySignals User Manual
Index © Libelium Comunicaciones Distribuidas S.L. INDEX 1. Introduction.......................................................................................................................................... 3 2. General and safety information.......................................................................................................... 3 3. MySignals’s Hardware Setup............................................................................................................... 4 3.1.
1. Introduction The aim of this manual is to introduce the user to MySignals in a practical way. This document applies to MySignals product, approved for FCC and IC: Model FCC ID IC MySignals XKM-MYSIGNAL-V1 8472A-MYSIGNALV1 2. General and safety information The following list shows just some of the actions that produce the most common failures and warranty-voiding cases. Failure to comply with the recommendations of use will entail the guarantee cancellation.
3. MySignals’s Hardware Setup All the items included in the basic kit of MySignals are in their specific compartiments in MySignals briefcase. Figure : Mysignals briefcase 3.1. Power Supply General power supply Operating Current 2A Operating Voltage 5V Input Voltage (recommended) 12V Input Voltage (limit) 10-20V DC Current per I/O Pin 20 mA [Max] DC Current for 3.
3.2. Sensors Figure : Mysignals sensors You can find all the sensor connectors indicated in both sides of the device.
Connect the correct sensor in each specific connector as you can see in the following images: Figure : Connecting one sensor This information is used to monitor in real time the state of a user or to get sensitive data in order to be subsequently analysed for biometric analysis. Biometric information gathered can be wirelessly sent using two connectivity options available: Wi-Fi or Bluetooth Low Energy 4.0.
Patient Position Sensor Description: The Patient Position Sensor (Accelerometer) monitors five different user positions (standing/sitting, supine, prone, left and right.). Body Position Sensor uses a triple axis accelerometer to obtain the user’s position. Measurement: Parameter Unit Range Body Position Dimensionless 5 different positions Body Temperature Sensor Description: Exacon D-S18JK sensor allows you to measure this key parameter for body monitoring.
Galvanic Skin Response Sensor (GSR - Sweating) Description: This sensor measures the electrical conductance of the skin, which varies with its moisture level. This is of interest because the sweat glands are controlled by the sympathetic nervous system, so moments of strong emotion, change the electrical resistance of the skin.
Spirometer Description: MSA100 Peak Flow Meter is a hand-held pulmonary function measuring device that measures your maximum possible exhalation which is called peak expiratory flow (PEF) and forced expiratory volume in 1 second (FEV1). FDA,ISO,CE. Measurement: Parameter Unit Range Volume l 0.01L~9.
Wireless Body Scale Description: Multipurpose personal portable digital weight health body scale Measurement: Parameter Unit Range Weight Kilograms 5-150Kg Bone Percentage 0-100% Body fat Percentage 0-100% Muscle mass Percentage 0-100% Body water Percentage 0-100% Visceral fat Percentage 0-100% BMI Kcal 0-500Kcal BMR Kcal 0-500Kcal 3.3. Data Visualization The e-Health library include graphic TFT for visualizing data. This 2.
3.4. Mini USB Data Transfer This connector is used to update code into MySignals with a male USB to male Mini USB cable provided by Libelium. Just connect one side of the cable to this connector, removing protection cap from MySignals and connect the other side to a PC to update a code. Figure : USB connector and protective cap When uploading processes are finished, do not forget to use again protection cap to avoid connector damage. 3.5.
4.2. MySignal Web Server Application Telemedicine is the use of telecommunication and information technologies in order to provide clinical health care at a distance. It helps eliminate distance barriers and can improve access to services that would often not be consistently available in distant rural communities. It is also used to save lives in critical care and emergency situations. MySignals allows to share data with the cloud, and perform real-time analysis.
Connecting to an iPhone a) Download the application from App Store: b) Download the application (MySignals.ipa) from the Libelium website: http://www.libelium.com/apps •• •• •• Then double click on the icon, or right click and open with iTunes. Inside iTunes, on the left panel, click on DEVICES->Your Device. Select on the top “Apps”, and select Sync Apps. Drag into the desired screen e-Health app. Once installed, the app appears in your iPhone/iPod screen.
5.1. MySignals Standalone Screen The sensor measures are distributed in different screens that change by pressing in the Screen. In the first screen you can configure the operating mode: BLE, WIFI or standalone. Figure : MySignals configuration screen In bluetooth mode you can configure the connection and then MySignals APP will start to receive data from MySignals.
There are several basic configuration screens: language, profile, user… Figure : MySignals basic configuration screen 5.2. MySignals Web Server Application MySignals application will have an user account to login into the system, this account is important to make cloud call and store information. If the user does not have an account the user cannot use MySignals application. Each account will be able to have one or more profiles, let’s think about a doctor that has many users, each user is a profile.
Using the Department, User or Device configuration sections you can create, configure or delete them.
Figure : Device configuration MySignals Web You can configure too your personal profile.
How do I ensure the privacy of the biometric data sent? Privacy is one of the key points in this kind of applications. For this reason the platform includes several security levels: •• •• In the communication link layer: WPA2 for Wifi. In the application layer: by using the HTTPS (secure) protocol we ensure a point to point security tunnel between each sensor node and the web server (this is the same method as used in the bank transfers). 5.3.
Then you can select the sensor that you want to monitor and MySignals will start to monitor all the parameters.
6. Updating a New Firmware to MySignals Using the USB connector, a new firmware version can be uploaded to MySignals without opening the enclosure. Just connect one side of the USB cable to this connector, removing protection cap if necessary and connect the other side to a PC. Next steps describe this process in detail. 6.1. MySignals Updater Tool Step 1: Open the USB connector Remove the protection cap of the USB connector.
7.1. USA and Canada Certification Modification statement Libelium has not approved any changes or modifications to this device by the user. Any changes or modifications could void the user’s authority to operate the equipment. Interference statement This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s).
