ACCESSING INSTALLATION MENU 1 2 Press and hold the SETTINGS button for more than 5 seconds. PICTURE TIME OPTION NETWORK INPUT MY MEDIA or PICTURE AUDIO TIME OPTION NETWORK MY MEDIA Press the 0 button four times. Press the OK button. HDMI (DTV) No Signal or 3 ENG ENGLISH Accessing Installation Menu HDMI DTV No Signal When the Installation Menu is displayed, select the item you want. Installation Menu (V 3.
ACCESSING INSTALLATION MENU ENGLISH ENG Installation Menu NOTE yyDefault values may differ by region. The LG Digital Signage Setup menu This menu is used after installation to configure the Digital Signage. Installation Menu (V 3.0) LG Digital Signage Setup USB Cloning Password Change Set ID Setup Configuration Setup Lock Mode Fail Over SuperSign Server Setup Easy Brightness Control S/W : xx.xx.xx.xx Micom : x.xx.
ACCESSING INSTALLATION MENU 3 Key Operation IR Operation Set LG IR Operation to On (Work) or Off (Do Not Work) to enable or disable the remote control. yy (0 - Normal, 1 - Use PWR Only, 2 - Block All) Selecting Block All sets your monitor to block all key signals coming from general LG remote controls. yy Selecting Use PWR Only sets your monitor to block all key signals coming from general LG remote yy controls except for the Power key signal.
ACCESSING INSTALLATION MENU Power On Default (Input Source, A/V Setting, Aspect Ratio) ENGLISH ENG With the power turned on, you can set the Input Source, A/V Setting and Aspect Ratio options. yy Set to Yes (Work) or No (Do Not Work). yy If Power On Default is set to No, Input Source and Volume are deactivated. yy When Power On Default is set to Yes, it can set by entering the subordinate menu. yy (It may not work depending upon the model.
ACCESSING INSTALLATION MENU 5 Speaker Sync Mode With Sync Mode enabled, monitors connected with RS232C can start playing contents distributed by yy the Supersign Elite-w such as a video or an image simultaneously. If Sync Mode is set to Off, the function is disabled. yy If Sync Mode is set to Master for a monitor, it is set as the primary monitor. yy If Sync Mode is set to Slave for a monitor, it plays a content file at the same time as the master monitor. yy (It may not work depending upon the model.
ACCESSING INSTALLATION MENU Pivot Mode ENGLISH ENG It Inverts the screen display 180 degrees. yy It inverts both Input video signal and OSD. yy The available options are Off, On. yy If it is set to Off, the function is disabled. yy If it is set to On, the screen display is inverted 180 degrees. yy Pivot Mode is applied after rebooting. yy (It may not work depending upon the model.) OSD Portrait Mode (Off, 90, 270) Rotate the OSD clockwise. yy The available options are Off, 90° or 270°.
ACCESSING INSTALLATION MENU LG Digital Signage Setup Yes/ No Key Operation IR Operation Local key Operation Limted Mode Input Source Change Menu Display OSD Display Power On Default Input Source A/V Setting (Video Setting) Aspect Ratio Signage Mode Operation Yes NO User Yes/ No Normal/ Use PWR Only/ Block All Normal/ Use PWR Only/ Block All Yes/ No Yes/ No STD (Actual operations are performed in LST status) No Normal Normal No Yes User User User User User STD (Actual operations are performed in LST
ACCESSING INSTALLATION MENU USB Cloning ENGLISH ENG The administrator can configure a monitor more quickly through USB and configure multiple monitors simultaneously. All monitors that have been configured this way operate according to the settings of the same master monitor.This newer procedure significantly decreases the installation time that would be necessary if the standard RS-232C method were used instead.
ACCESSING INSTALLATION MENU 9 Receive from USB ENG ENGLISH Receive from USB USB Cloning Select file type Ez Download Global TLL Receive from USB Model TLL Send to USB GlobalClone00001.TLL Logo Image Download GlobalClone99999.TLL No Signal Image Download Send to Daisy Chain OK Previous 1 Use the OK Previous button to select the desired *.TTL files name and press the OK button. 2 The monitor is changed to Standby mode after a successful download.
ACCESSING INSTALLATION MENU Logo Image Download ENGLISH ENG You can download a Splash Image file on your monitor. Make a LG_DTV folder on the USB flash drive and then copy the splash image file to that folder. 1 Use the button to select the desired file name and press the OK button. USB Cloning Logo Image Download Ez Download Image1.jpg Receive from USB Image2.jpg Send to USB Image3.
ACCESSING INSTALLATION MENU 11 Send to daisy chain 1 You can send the settings for the current set to other sets using the RS232C output. 2 The settings of the first set, which is RS232C daisy chained, are copied. 3 After selecting Send to Daisy Chain, select Yes to send the data or No to return to the menu. 4 The function attempts to copy the settings until the sets connected to RS232C out port of the current set are powered off.
ACCESSING INSTALLATION MENU Password Change ENGLISH ENG You can change the password for security. Enter a new 4-digit number in Change Password. Enter the same number again in Confirm Password to confirm the password. Installation Menu (V 3.0) LG Digital Signage Setup USB Cloning Password Change Set ID Setup Configuration Setup Lock Mode Fail Over SuperSign Server Setup Easy Brightness Control S/W : xx.xx.xx.xx Micom : x.xx.
ACCESSING INSTALLATION MENU 13 Password Change ENG ENGLISH You can change the password for security. Enter a new 4-digit number in Change Password. Enter the same number again in Confirm Password to confirm the password. Installation Menu (V 3.0) LG Digital Signage Setup USB Cloning Password Change Set ID Setup Configuration Setup Lock Mode Fail Over SuperSign Server Setup Easy Brightness Control S/W : xx.xx.xx.xx Micom : x.xx.
ACCESSING INSTALLATION MENU Configuration Setup ENGLISH ENG This feature enables the detailed configuration of the product. Installation Menu (V 3.0) Configuration Setup LG Digital Signage Setup USB Cloning Password Change Set ID Setup Configuration Setup Lock Mode Fail Over SuperSign Server Setup Easy Brightness Control S/W : xx.xx.xx.xx Micom : x.xx.
ACCESSING INSTALLATION MENU 15 Lock Mode Installation Menu (V 3.0) LG Digital Signage Setup USB Cloning Password Change Set ID Setup Configuration Setup Lock Mode Fail Over SuperSign Server Setup Easy Brightness Control S/W : xx.xx.xx.xx Micom : x.xx.x Lock Mode USB Initial Setting Previous Enable Enable OK OK USB You can enable/disable USB input. The following will happen when USB input is disabled. yy The pop-up window that appears when a USB disk is connected to your monitor is blocked.
ACCESSING INSTALLATION MENU Fail Over ENGLISH ENG This feature enables an automatic switch to another input with a signal when there is no signal from the current input of the product. Installation Menu (V 3.0) Fail Over LG Digital Signage Setup USB Cloning Password Change Set ID Setup Configuration Setup Lock Mode Fail Over SuperSign Server Setup Easy Brightness Control Mode USB Priority1 Priority2 Priority3 Previous S/W : xx.xx.xx.xx Micom : x.xx.
ACCESSING INSTALLATION MENU 17 NOTE ENG ENGLISH yyThe number of priorities may vary depending on the model. yyWhen the Mode is set to Off, all of the submenus are disabled. yyWhen the Mode is set to Auto, the submenus of Priority1, Priority2, and Priority3 are disabled. yyIf you select Movie or Photo in the USB menu, the USB Auto Playback option in Configuration Setup is disabled and the function does not work.
ACCESSING INSTALLATION MENU SuperSign Server Setup ENGLISH ENG This feature is for a linkage with SuperSign Manager. Installation Menu (V 3.0) Fail Over LG Digital Signage Setup USB Cloning Password Change Set ID Setup Configuration Setup Lock Mode Fail Over SuperSign Server Setup Easy Brightness Control S/W : xx.xx.xx.xx Micom : x.xx.x Mode USB Priority1 Priority2 Priority3 Previous Off Off ------------OK OK Player Name You can set the name of a player you want to control in SuperSign Manager.
ACCESSING INSTALLATION MENU 19 Easy Brightness Control Installation Menu (V 3.0) LG Digital Signage Setup USB Cloning Password Change Set ID Setup Configuration Setup Lock Mode Fail Over SuperSign Server Setup Easy Brightness Control S/W : xx.xx.xx.xx Micom : x.xx.
ACCESSING INSTALLATION MENU ENGLISH ENG CONTROLLING THE MULTIPLE PRODUCT Use this method to connect several products to a single PC. You can control several products at one yy time by connecting them to a single PC. In the Option menu, Set ID must be between 1 and 255 (or from 1 to 1,000) without being duplicated. yy Connecting the cable Connect the RS-232C cable as shown in the picture. The RS-232C protocol is used for communication between the PC and product.