Internal Use Only Description - Model : RBHP-B216C - Bluetooth: v4.2+EDR - WLAN : 802.11 a/b/g/n/ac - Frequency Range : 2400MHz ~ 5835MHz - Device Type : OEM Device installed in vehicles Features - Dimension : 22.5mm x 20.0mm x 2.7mm - Temperature Range : -40℃ ~ +85℃ - Supply Voltage : VBAT 3.0V to 3.6V - Output Power BT: Typ. +1.5dBm(Class 2) WLAN : 16.0dBm(b), 13dBm(g), 12dBm(n), 13dBm(a), 10dBm(ac) - Interface PCIe(WLAN), UART(BT), I2S Application - Automotive Dimensions pyrightⓒ. 2017.
Internal Use Only • Power Supply Specification One Buck regulator, multiple LDO regulators, and a power management unit(PMU) are integrated into the BCM88359. All regulators are programmable via the PMU. These blocks simplify power supply design for Bluetooth and WLAN functions in embedded designs. A single VBAT(3.0V to 3.6V DC max) and VIO supply (1.8V to 3.3V) can be used, with all additional voltages being provided by the regulators in the BCM88359.
Internal Use Only *Boot sequence pyrightⓒ. 2017. All Rights Reserved.
Internal Use Only General Features RBHP-B216C satisfies the following standards 1)Bluetooth Features Bluetooth Power Class 2. Provisioned for low energy angle-of –arrival applications. Complies with Bluetooth Core Specification Version 4.2 with provisions for supporting future specifications. Supports extended synchronous connections(eSCO), for enhanced voice quality by allowing for retransmission of dropped packets. Adaptive frequency hopping(AFH) for reducing radio frequency interference.
Internal Use Only PIN Description pyrightⓒ. 2017. All Rights Reserved.
Internal Use Only PIN Description pyrightⓒ. 2017. All Rights Reserved.
Internal Use Only PIN Description pyrightⓒ. 2017. All Rights Reserved.
Internal Use Only FCC MODULAR APPROVAL INFORMATION EXAMPLES for Manual This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Internal Use Only OEM INTEGRATION INSTRUCTIONS: This device is intended only for OEM integrators under the following conditions: The module must be installed in the host equipment such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the internal on-board antenna that has been originally tested and certified with this module. External antennas are not supported.
Internal Use Only FCC MODULAR APPROVAL INFORMATION EXAMPLES for Manual This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Internal Use Only IC Information This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s).
Internal Use Only Requirement per KDB996369 D03 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentionalradiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.
Internal Use Only 2.5 Trace antenna designs For a modular transmitter with trace antenna designs, see the guidance in Question 11 of KDB Publication 996369 D02 FAQ – Modules for Micro-Strip Antennas and traces. The integration information shall include for the TCB review the integration instructions for the following aspects: layout of trace design, parts list (BOM), antenna, connectors, and isolation requirements. a) Information that includes permitted variances (e.g.
Internal Use Only 2.7 Antennas A list of antennas included in the application for certification must be provided in the instructions. For modular transmitters approved as limited modules, all applicable professional installer instructions must be included as part of the information to the host product manufacturer. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc. (note that for example an “omnidirectional antenna” is not considered to be a specific “antenna type”)).
Internal Use Only This radio transmitter [7414C-RBHPB216C1] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. WLAN 2.