User Manual PRODUCT NAME : RF Module MODEL NAME ETWFAEWC01 : The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek. LG Innotek Co., Ltd.
DOCUMENT No. : User Manual REG. DATE : 2020.04.09 REV. DATE : 2020.04.09 MODEL NAME : ETWFAEWC01 WC40154 REV. NO : v1.0 PAGE : 1 / 7 Table of Contents No Description Page 1 Features 2 2 Picture of Product 2 3 Block Diagram 3 4 Absolute Maximum Ratings 3 5 Operating Test Conditions 4 6 Standard Test Conditions 4 7 Pin Description 5 8 Outline Drawing 6 9 Packing Information 7 ©2020 LGIT. All rights reserved.
DOCUMENT No. : User Manual REG. DATE : 2020.04.09 REV. DATE : 2020.04.09 MODEL NAME : ETWFAEWC01 REV. NO : v1.0 PAGE : 2 / 7 1. Features ETWFAEWC01 is the module for IEEE 802.11b/g/n wireless LAN. ETWFAEWC01 is based on ESP32-D0WDQ6 solution. IEEE 802.11 b/g/n single band WLAN infrastructure Size : 70mm x 70mm x 15mm 802.11n, up to 150Mbps PHY rate CAN 2.
DOCUMENT No. : User Manual REG. DATE : 2020.04.09 REV. DATE : 2020.04.09 WC40154 REV. NO : v1.0 MODEL NAME : ETWFAEWC01 PAGE : 3 / 7 3. Block Diagram 4. Absolute Maximum Ratings Parameter Min Max Unit Storage Temperature -40 +85 ℃ Storage Humidity (@ 40℃) - 90 % Caution : The specifications above the Table define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions.
DOCUMENT No. : User Manual REG. DATE : 2020.04.09 REV. DATE : 2020.04.09 WC40154 REV. NO : v1.0 MODEL NAME : ETWFAEWC01 PAGE : 4 / 7 5. Operating Test Conditions 1) Parameter Min Typ Max Unit Operating Temperature1) -20 - +70 ℃ Operating Humidity (40℃) - - 85 % Supply Voltage1) 10.8 12 13.2 Vdc It can be operated from 8V to 16V, but this voltage range shouldn’t be guaranteed 6.
DOCUMENT No. : User Manual REG. DATE : 2020.04.09 REV. NO : v1.0 MODEL NAME : ETWFAEWC01 REV. DATE : 2020.04.09 WC40154 PAGE : 5 / 7 7. Pin Description Connector Pin No. Pin Name I/O Pin Description 1 GND P Ground 2 12V P Power Supply 3 CAN_L I/O Low-level CAN bus line 4 CAN_H I/O High-level CAN bus line - R45 - Ethernet Connector CON1 CON2 < Top View > CON2 CON1 Pin #1 Pin #4 ©2020 LGIT. All rights reserved.
DOCUMENT No. : User Manual REG. DATE : 2020.04.09 REV. DATE : 2020.04.09 MODEL NAME : ETWFAEWC01 8. Outline Drawing ©2020 LGIT. All rights reserved. WC40154 REV. NO : v1.
DOCUMENT No. : User Manual REG. DATE : 2020.04.09 MODEL NAME : ETWFAEWC01 REV. DATE : 2020.04.09 9. Packing Information FIFO Label BARCODE Label NOT FULL Label '20. 03. 06 Lee Kap Soul. '20. 03. 06 Lee Jin Kuk. '20. 03. 06 Choi Seok Dong. ©2020 LGIT. All rights reserved. WC40154 REV. NO : v1.
DOCUMENT No. : User Manual REG. DATE : 2020.04.09 REV. DATE : 2020.04.09 MODEL NAME : ETWFAEWC01 WC40154 REV. NO : v1.0 PAGE : 8 / 7 10. FCC/IC Statement FCC Part 15.19 Statements: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accep t any interference received, including interference that may ca use undesired operation.
DOCUMENT No. : User Manual REG. DATE : 2020.04.09 REV. DATE : 2020.04.09 WC40154 REV. NO : v1.0 MODEL NAME : ETWFAEWC01 PAGE : 9 / 7 10. FCC/IC Statement Antennas list This radio transmitter [ETWFAEWC01] has been approved by I nnovation, Science and Economic Development Canada to op erate with the antenna types listed below, with the maximum permissible gain indicated.
DOCUMENT No. : User Manual REG. DATE : 2020.04.09 REV. DATE : 2020.04.09 MODEL NAME : ETWFAEWC01 WC40154 REV. NO : v1.0 PAGE : 10 / 7 10. FCC/IC Statement Professional Installation This device and antenna can only be installed by professionally trained personnel. Antenna should be used the same type and lower gain antenna described below. - External PCB Antenna - Max. antenna gain: 1.50 dBi Any new antenna type, higher gain than listed antenna should be met the requirements of FCC rule 15.203 and 2.