ATC5CPC001 User Manual Description - Model : ATC5CPC001 - WLAN : 802.11 a/b/g/n/ac - Frequency Range : 2400MHz ~ 5845MHz Features - Dimension : 22.5mm x 20.0mm x 2.9mm - Temperature Range : -40℃ ~ +85℃ - Supply Voltage : VBAT 3.2V to 3.6V - Output Power WLAN : 17.0dBm(11b 11Mbps), 16dBm(11g 54Mbps, 11n 2.4G MCS7), 15dBm(11a 54Mbps), 14dBm(11n 5G MCS7), 11dBm(11ac MCS9) - Interface : PCIe(WLAN) Application - Automotive (Outdoor Device) Dimensions Copyrightⓒ. 2019. All Rights Reserved.
ATC5CPC001 User Manual Operating condition 1) Recommended operation conditions Parameter Min. Typ. Max. Unit Operating Temperature Range -40 - +85 ℃ Supply Voltage : VBATT (3.3V)1) 3.2 3.3 3.6 V 1.62 1.8 1.98 V 2.97 3.3 3.63 V Supply Voltage : VIO 2) Current consumption Parameter Average Max. Unit Stand-by (BT & WLAN) 5 10 mA WLAN Continuous Rx2) 280 360 V WLAN Continuous Tx2) 790 1,000 V Bluetooth Connection 35 40 V Leakage current 15 Copyrightⓒ. 2019.
ATC5CPC001 User Manual Boot up sequence > 0ms VBAT VIO 100us WL_REG_ON VDDC (on-chip PMU) Max. 12.4msec PCIE_CLKREQ_L PCIE_REFCLK 21.2msec PCIE_PERST_L 6msec Copyrightⓒ. 2019. All Rights Reserved.
ATC5CPC001 User Manual General Features • Operation Voltage is 3.3V/1.8V Dual Power Rail • Up to 866 Mbps data rate • Support 2 Antenna port : BT and WLAN ANT1, WLAN ANT2 • Integrated External RF Switch and Internal PA/LNA at 2.4GHz, Internal PA and External RF Switch and LNA at 5GHz • RoHS Compliant • Size : 22.5 x 20.0 x 2.9 mm3 • Support bandwidth : HT20 / HT40 / VHT80 • Interface : PCIe(WLAN), UART(BT),PCM/I2S • Package type : SMD type(Side-via) Copyrightⓒ. 2019. All Rights Reserved.
ATC5CPC001 User Manual General Features BT(v5.0) + 2.4GHz/5GHz WiFi 5 (802.11a/b/g/n/ac) 2x2 MIMO Module Bluetooth(BT5.0 compliant) 1) Bluetooth Key Features • Supports key features of upcoming Bluetooth standards • Fully supports Bluetooth Core Specification version 4.2 + (Enhanced Data Rate) EDR features: -. Adaptive Frequency Hopping (AFH) -. Quality of Service (QoS) -. Extended Synchronous Connections (eSCO) – Voice Connections -. Fast Connect (interlaced page and inquiry scans) -.
ATC5CPC001 User Manual General Features WLAN 1) WLAN RF band & modulation Features • Dual-band 2.4GHz and 5GHz WiFi 5 (802.11a/b/g/n/ac) • Dual-stream up to 866Mbps data rate • Supports 20, 40 and 80MHz channels with optional SGI(256 QAM modulation) • Tx and Rx low-density parity check(LDPC) • Supports IEEE 802.11ac/n beamforming • Supports two antennas with one dedicated to Bluetooth and WLAN and one to WLAN. • PCIe mode complies with PCI Express base specification revision 3.
ATC5CPC001 User Manual General Features WLAN 3) WLAN PHY features • Programmable data rates from MCS0-9 in 20MHz, 40MHz, and 80MHz channels, as specified in IEEE 802.11ac • Improved performance with 2x2 channel smoothing and spur canceller support • Supports Optional short GI and Green field modes in Tx and Rx • Tx and Rx LDPC for improved range and power efficiency • Beamforming support • Supports IEEE 802.
ATC5CPC001 User Manual Pin Configuration 44 43 42 41 40 39 38 37 36 35 34 33 32 1 31 2 30 3 29 45 47 4 28 5 27 6 26 46 48 7 25 8 24 9 23 10 11 12 13 Copyrightⓒ. 2019. All Rights Reserved.
ATC5CPC001 User Manual Pin Configuration No. Pin Name I/O Description 1 PCIE_CLK_P I PCIE differential clock input positive 2 PCIE_CLK_N I PCIE differential clock input negative 3 PCIE_TD_N O PCIE Transmitter differential negative 4 PCIE_TD_P O PCIE Transmitter differential positive 5 N.C. - Not Connected (Reserved) 6 N.C. - Not Connected (Reserved) 7 N.C. - Not Connected (Reserved) 8 N.C. - Not Connected (Reserved) 9 N.C. - Not Connected (Reserved) 10 N.C.
ATC5CPC001 User Manual Pin Configuration No. Pin Name I/O 19 BT_PCM_CLK I/O PCM clock, can be master (output) or slave (input) 20 BT_PCM_SYNC I/O PCM sync signal, can be master (output) or slave (input) 21 BT_PCM_IN I/O PCM data input 22 BT_PCM_OUT I/O PCM data output 23 WL_ANT 1 RF BT/WLAN RF ANT 1 24 GND - Ground 25 LPO I Low power clock input(32.768KHz, 0V ~ 1.
ATC5CPC001 User Manual Pin Configuration No. Pin Name I/O Description 37 VIO I BT, WLAN VDDIO supply voltage.(3.3V or 1.8V) - BT and WLAN should be same power rail 38 SDIO_DIS I SDIO_DIABLE : Low : SDIO Enabled, High : SDIO Disabled 39 PCIE_EN I PCIE_ENABLE : Low : PCIE Disabled, High : PCIE Enabled 40 PCIE_PME_L O PCIE power management event output 41 PCIE_PERST_N I PCIE system reset.
FCC MODULAR APPROVAL INFORMATION EXAMPLES for Manual This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
OEM INTEGRATION INSTRUCTIONS: This device is intended only for OEM integrators under the following conditions: The module must be installed in the host equipment such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the internal on-board antenna that has been originally tested and certified with this module. External antennas are not supported.
FCC MODULAR APPROVAL INFORMATION EXAMPLES for Manual This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
IC Information This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s).
Requirement per KDB996369 D03 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.
2.5 Trace antenna designs For a modular transmitter with trace antenna designs, see the guidance in Question 11 of KDB Publication 996369 D02 FAQ – Modules for Micro-Strip Antennas and traces. The integration information shall include for the TCB review the integration instructions for the following aspects: layout of trace design, parts list (BOM), antenna, connectors, and isolation requirements. a) Information that includes permitted variances (e.g.
2.7 Antennas A list of antennas included in the application for certification must be provided in the instructions. For modular transmitters approved as limited modules, all applicable professional installer instructions must be included as part of the information to the host product manufacturer. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc. (note that for example an “omni-directional antenna” is not considered to be a specific “antenna type”)).
2.10 Additional testing, Part 15 Subpart B disclaimer The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
