INSTALLING THE HOME STATION 1. P osition the home station against a wall on hard, level flooring to prevent sliding during docking. It is not recommended to install the home station on carpet. Doing so may cause the Robot Cleaner to have difficulty docking. Remove objects within 5 ft. (1.5 m) to the right and left side and within 61/2 ft. (2 m) to the front. 5 ft. (1.5 m) 5 ft. (1.5 m) 61/2 ft. (2 m) 2. Plug the jack into the home station. 3. Plug the power cord into an outlet.
TURNING THE Robot Cleaner ON/OFF Turning On the Main Power Supply Flip the power switch to the ON position. ※D o not press the Start/Stop button at the same time as flipping the power switch. Doing so may delay the operation. ※ Turn off the power switch when the Robot Cleaner is not used for long periods. The switch must be turned back on for the Robot Cleaner to charge.
HOW TO START AND STOP CLEANING Using the Robot Cleaner's Buttons Once the Robot Cleaner is turned on, press the START/STOP button on the top of the Robot Cleaner to begin cleaning. A melody sounds and cleaning begins. Press the START/STOP button any time during the cleaning cycle to stop cleaning. ※ To start cleaning when the Robot Cleaner is in standby mode, press START/STOP once to turn on the power, then press again to start cleaning.
CHARGING THE BATTERY Automatic charging The Robot Cleaner returns to the home station at the end of a cleaning cycle or when its battery is running low. ※ If 10 minutes elapse without the Robot Cleaner moving or the battery is too low, the Robot Cleaner automatically goes into standby mode. ※ The power switch has to be in the ON position in order for the Robot Cleaner to charge at the home station. If the switch is OFF, an error message sounds.
CHARGING THE BATTERY Battery Level Indicator The battery level indicator is located on the status display. • The battery level indicator flashes if recharging is in progress, showing the charge level. • If recharging is complete, only the battery and clean mode icons are displayed to save energy. • The first level of the battery level icon flashes when the Robot Cleaner needs to be charged.
CHARGING THE BATTERY Energy Saving Charging Mode You can recharge the battery with the Energy Saving mode, if you don't use the Robot Cleaner for a long period of time or overnight. Step 1. P ress the On/Off button on the remote. All functions of the Robot Cleaner are turned off except the recharging mode. ※ After recharging is complete, press the On/Off button on the remote to use the Robot Cleaner.
CHOOSING A CLEANING MODE Zigzag Cleaning In Zigzag mode, the Robot Cleaner zigzags through each spot of the cleaning area. Select the Zigzag mode to quickly clean an area. Selecting the Zigzag Mode Press the Mode button continuously, on either the Robot Cleaner or remote, until the Zigzag icon illuminates. ※ The default mode on the Robot Cleaner is the Zigzag mode. Cell by Cell Cleaning Select the Cell by Cell mode for meticulous cleaning.
CHOOSING A CLEANING MODE My Space Cleaning Select the My Space mode to manually set the cleaning space. Selecting the My Space Mode 1. Press the My Space button. 2. Using the arrow buttons on the remote, guide the Robot Cleaner around the perimeter of the desired cleaning space. ※ Cleaning space must be smaller than 31/4 ft. (3 m). My Space 3. Once the area is specified, press the Start button. NOTE: If the cleaning area is not correctly outlined, an error message sounds.
AUXILIARY CLEANING MODES Manual Cleaning Manual mode moves the Robot Cleaner manually to the front, back and either side using the arrow buttons on the remote. While in Manual mode, the Robot Cleaner runs into obstacles placed behind it if the back arrow key on the remote is held down. Spot Cleaning The Spot mode cleans the area where it is placed within a 41/2 ft (1.37 m) diameter. Starting Spot Mode 1. Place the Robot Cleaner in the desired cleaning area. 2.
AUXILIARY CLEANING MODES Turbo Mode Select Turbo Mode for a more intense, powerful clean. Turbo Mode reduces the battery duration. Selecting Turbo Mode Press the Turbo button on the remote or on the Robot Cleaner to activate the Turbo mode. Press the Turbo button at any time during the cleaning operation to cancel the Turbo mode. ※ Turbo Mode (Floor Master Function) Turbo mode activates automatically on carpets.
SETTING THE CLOCK You can set or change the current time on the Robot Cleaner. Pressing the Clock button on the remote when the Robot Cleaner is in standby mode starts the clock setting mode. Flickering Flickering s Select by using s buttons on the remote. The function can be heard through the voice guide. Flickering Set the hour by using uv buttons on the remote. Set the minutes using uv buttons on the remote. Set AM/PM using uv buttons on the remote.
SCHEDULING CLEANING Cleaning can be scheduled so that the Robot Cleaner starts cleaning at a scheduled time. Press the Schedule button on the remote while the Robot Cleaner is recharging to set a scheduled cleaning. Setting/Cancelling a scheduled cleaning is only possible when the unit is recharging on the home station Flickering Select Schedule Once or Schedule Daily option using the uv buttons on the remote. A voice message confirms the schedule. Set the hour using the uv buttons on the remote.
MOP CLEANING (on some models) Remove dust on hard floors by attaching the ultra microfiber mop to the Robot Cleaner. When the mop plate is attached, the Robot Cleaner will not climb on to carpets or over thresholds, in order to prevent transferring dirt from the mop. Caution Do not cover the bottom camera sensor with the mop. For mop cleaning, mount the mop and mop plate to the Robot Cleaner according to the following instructions: 1.
LOCATION SEARCH FUNCTION The Robot Cleaner remembers its location while cleaning. If the user moves the Robot Cleaner while it is operating, it will search for the location it was moved from by using its navigational location search function before continuing to clean. ※ The navigational function is activated after the Robot Cleaner adequately recognizes the cleaning environment. Change location Manual Relocation. 1. With the power off, locate the Robot Cleaner near where it was originally moved from.
SMART DIAGNOSIS™ Robot Cleaner uses the Smart Diagnosis feature to run a self-diagnosis. If any irregularity is found from the diagnosis, contact the local LG Electronics service center. ※ During Smart Diagnosis, the Robot Cleaner moves about within a 11/5 ft. (50 cm) radius. So, make sure no objects are in the way within a 31/4 ft. (1 m) radius around the home station, before starting Smart Diagnosis. 1.
SMART DIAGNOSIS™ Refer to the following table to resolve error messages encountered during Smart Diagnosis. Voice message Solution Robot Cleaner Smart Diagnosis will be started. Please step away and clear around 1 meter around the home station. Clear any object within a 31/4 ft. (1 m)radius around Home Station, and stay back until the diagnosis is complete. Smart Diagnosis can start when it is being charged. Please dock Robot Cleaner to the home station to charge.
CLEANING THE DUST BIN If the dust bin is full, suction power can be reduced. Clean the dust bin before or after each cleaning session. Clean the dust bin using the following sequence: 1. O pen the dust bin compartment cover by pressing the PUSH button on the Robot Cleaner. 2. G rab the handle of the dust bin and pull it upward. 3. P ull the hook on the left of the filter cover on the rear of the dust bin to separate the filter and the sponge.
CLEANING THE DUST BIN FILTER The Dust Bin Filter consists of a particulate filter and a sponge filter. Clean both the particulate filter and sponge filters using the following sequence. 1. Pull the hook on the left of the particulate filter module on the rear side of the dust bin to separate the particulate filter and the sponge filter. 2. T horoughly clean out the fine dust particles on the particulate filter with a vacuum cleaner or cleaning brush. ※ Do NOT wash the particulate filter with water.
CLEANING THE BRUSH The rotating brush, located on the bottom of the Robot Cleaner, helps collect dust. Clean the brush using the following sequence. ※ Before turning over the main unit, lay a soft cloth on the floor and remove the Dust Bin. Otherwise, the main unit can get scratched and dust will fall from the Dust Bin. Turn the main power switch OFF before starting to clean. Put the Robot Cleaner upside down on a soft cloth.
CLEANING THE SENSORS/CHARGING TERMINALS There are sensors on the Robot Cleaner that detect obstacles, stairways and the home station for charging the battery. In order to maintain the performance of the Robot Cleaner, regularly clean the sensors and charging terminals as follows: 1. Turn off the power switch on the rear side of the Robot Cleaner. Injury can be caused by the activation of the Robot Cleaner if the main power is not turned off. 2.
als CLEANING THE SIDE BRUSH Foreign objects/materials such as hair can easily adhere to the side brush. Remove such materials at least once a week. If excessive amounts of foreign materials are stuck to the brush, there is the risk of damage to the brushes. If the floor is rough or frequently cleaned, the side brushes may bend or become deformed. In this case, use the following method to straighten the side brush. 1. The following procedure is helpful in restoring deformed brushes. 2.
CLEANING THE ULTRA MICROFIBER MOP (on some models) To avoid odors, dirt and dust should be washed off the mop after it is used for cleaning. Follow these directions to wash the ultra microfiber mop: 1. Separate the ultra microfiber mop from the mop plate. 210 mm 2. Carefully clean it with warm water. 3. Use the mop after completely drying it in direct sunlight. ※ I f the mop is used in a damp or wet state, it will cause the Robot Cleaner to malfunction.