STB1000 HD Commercial Interface Set-top Box for use in Lodging Environments Installation & Setup Guide Warranty © Copyright 2011, LG Electronics U.S.A., Inc.
For Customer Support/Service, please call: 1-888-865-3026 The latest product information and documentation is available online at: www.LGsolutions.com/products MODEL and SERIAL NUMBER The model and serial numbers of this STB are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here: Model No._________________Serial No.
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 20. Grounding Ensure that you connect the earth ground wire to prevent possible electric shock (i.e., an STB with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. 21.
Table of Contents Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . 3 – 4 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 STB1000 Rear and Front Panel Overview. . . . . . . . . . . . 7 STB1000 Jack Panel Overview . . . . . . . . . . . . . . . . . . . . 8 Ventilation / Mounting the STB1000 . . .
Setup Checklist Installation and Setup __ Unpack the STB1000 and all accessories. Accessories provided: • 6 ft AC power cord • 5 ft RS-232C-F to RS-232C-F null-modem cable with 3.5 mm stereo plug • 5 ft RS-232C-M to RS-232C-F straight-through cable • 5 ft HDMI to DVI-M cable • 1 ft DVI-F to HDMI adapter cable • 5 ft Audio cable with 3.5 mm stereo plugs • IR receiver with attached 3.
STB1000 Rear and Front Panel Overview STB1000 Rear Panel . DIGITAL VIDEO IN 2 ..... 1(DVI . . . . ). RJP INTERFAC E Y PB LAN PR ..RGB. ..(PC).. .. UPDATE OPTICAL DIGITAL AUDIO OUT TRO .. . . L .
STB1000 Jack Panel Overview UPDATE Restricted to software updates. TV-LINK CFG Use for local FTG configuration. MPI/GAME CONTROL When the EBL is in Pass-through Mode, the MPI function enables an external MPI control device (i.e., clone programmer, VOD/PPV STB, etc.) to control the STB. Game Control—EBL in LodgeNet PPV mode only. RESET Press to re-initialize the STB1000. LAN For future application. OPTICAL DIGITAL AUDIO OUT Use for amps and home theater systems.
Ventilation / Mounting the STB1000 Ventilation STB1000 Vent Holes The STB1000 generates heat during operation and needs to be provided with adequate ventilation to assure continued reliable operation. See recommendations below. Proper clearance for air to flow around the STB1000 must be provided. Note: While accommodating STB1000 ventilation requirements, also be sure proper ventilation is provided for the display panel.
STB1000 Cabling Connections Refer to the cabling diagram below, and complete the procedure on page 11 to connect the STB1000 to a compatible LG display panel. LAN RESET Y PR ......... REMOTE CONTROL OUT R L AUDIO VIDEO RJP INTERFACE DISPLAY CONTROL AUDIO (RGB/DVI) ............... PB SPEAKER OUT 8 UPDATE RGB(PC) RGB IN 1(DVI) .......... OPTICAL DIGITAL AUDIO OUT MPI/GAME CONTROL TV-LINK CFG DIGITAL VIDEO IN 2 ..........
STB1000 Cabling Connections (Cont.) 1. Use one of the supplied RS-232 cables—either the serial DB9-Female to DB9-Female null-modem cable or the DB9-Female to DB9-Male straight-through cable, depending on display panel requirements—to connect the DISPLAY CONTROL connector on the STB1000 jack panel to the RS-232 IN connector on the LG display panel.
STB1000 Installer Remote The LG Installer Remote is supplied with and dedicated to operate the STB1000. See next page for typical key functions. Some DVD and VCR controls may be available for selected LG DVD/VCR products. Installing Batteries in Installer Remote • Open the battery compartment cover on the back side of the remote. • Install two high-quality alkaline 1.5V AAA batteries. Never mix old or used batteries with new ones.
Installer Remote Control Typical Key Functions The LG Installer Remote illustrated below shows typical remote control functions and is provided for reference only. This Installer Remote may vary from the Installer Remote supplied with the STB1000. GUIDE Displays and removes the electronic program guide. PORTAL Displays and removes the interactive menu. TV POWER DVD PORTAL INFO i STB GUIDE TV/STB/DVD/VCR Select the remote’s operating mode: TV, STB, DVD, or VCR.
Pro:Centric Interactive Menu Features Important: Pro:Centric operation requires that Installer Menu item 119 DATA CHANNEL be set appropriately and that the STB1000 be in PPV or FTG Mode. Channel Guide Information Remote Help Watch TV The interactive Pro:Centric STB enables guests—from the comfort of their rooms—to view and select from a complete listing of hotel/institution services and amenities.
STB1000 Setup Menus On-screen setup menus control the basic features of the STB1000/display. Press MENU on the Installer Remote to access the STB1000 setup menus. Setup menu options are described in detail on pages 16 to 38. Note that on-screen displays (OSDs) shown in this manual may differ from those shown on the display panel. This document provides typical examples to familiarize you with the STB1000 options.
Channel Setup Options Auto Tuning (Channel Search) Auto Tuning (Channel Search) CHANNEL Auto Tuning automatically finds and stores all digital and analog channels available through antenna or cable inputs. Manual Tuning Channel Edit Channel Label 2. Use the Up/Down arrows to select Auto Tuning, and then press ENTER. Check your antenna connection. The previous channel information will be updated during Auto Tuning. 3.
Channel Setup Options (Cont.) Manual Tuning (Add/Delete Channels) / View Digital Signal Strength Manual Tuning (Add/Delete Channels) CHANNEL Use this option to manually add active channels or remove unwanted channels. See also “Edit Channels” on the following page. Auto Tuning Manual Tuning Channel Edit Channel Label 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the CHANNEL menu option. Then, press ENTER. 6.
Channel Setup Options (Cont.) Edit Channels / Channel Labels Edit Channels Use this option to add or delete channels from the channel lineup. 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the CHANNEL menu option. Then, press ENTER. CHANNEL Move Enter Auto Tuning Manual Tuning Channel Edit Channel Label 2. Use the Up/Down arrows to select Channel Edit, and then press ENTER.
Picture Setup Options Aspect Ratio (Picture Size) Control Aspect Ratio (Picture Size) Control This option enables you to choose the appropriate picture aspect ratio depending on the input source. Use the RATIO button on the Installer Remote or use the procedure below. PICTURE Aspect Ratio : 16:9 Picture Mode : Standard • Backlight 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the PICTURE menu option. Then, press ENTER.
Picture Setup Options (Cont.) Picture Mode Picture Mode PICTURE This feature enables you to select a preconfigured Picture Mode option and/or customize picture settings manually. 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the PICTURE menu option. Then, press ENTER.
Picture Setup Options (Cont.) Advanced Control Advanced Control PICTURE Picture Mode 2. Use the Up/Down arrows to select Advanced Control under Picture Mode, and then press ENTER. • Backlight • Contrast • Brightness • Sharpness • Color • Tint 90 Color Temperature Medium Dynamic Contrast Medium ► 90 50 Dynamic Color Low 50 Noise Reduction Medium 50 Gamma 0 Black Level R Medium G • Advanced Control Eye Care Low Off Real Cinema Off ► 4.
Picture Setup Options (Cont.) Picture Reset / RGB-PC Screen Settings This option restores the Picture Mode to factory default settings. 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the PICTURE menu option. Then, press ENTER. 2. Use the Up/Down arrows to select Picture Reset under Picture Mode, and then press ENTER. 3. At the prompt for confirmation, select Yes and press ENTER to continue.
Picture Setup Options (Cont.) RGB-PC Screen Settings (Cont.) Screen Auto Configuration This option automatically adjusts the picture position and minimizes image instability. SCREEN Prev. Resolution 1. In the Screen Menu, use the Up/Down arrows to select Auto Config, and then press ENTER. Auto Config. 2. Use the Left/Right arrows to select Yes, and then press ENTER to initiate the auto adjustment. Position 3.
Option Settings Menu Language / Audio Language Menu Language Use this option to select the language of on-screen menus. 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the OPTION menu option. Then, press ENTER. 2. Use the Up/Down arrows to select Menu Language, and then press ENTER. OPTION Move Menu Language : English Audio Language : English Caption : Off Set ID :1 Demo Mode : Off Data Broadcasting Enter English 3.
Option Settings (Cont.) Captions Captions OPTION Use this option to select the appropriate mode for displaying captions. Caption text, if provided by the broadcaster, is available for both digital and analog channels on the antenna/cable. Turn Captions On/Off 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the OPTION menu option. Then, press ENTER.
Option Settings (Cont.) Set ID / Demo Mode Set ID 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the OPTION menu option. Then, press ENTER. 2. Use the Up/Down arrows to select Set ID, and then press ENTER. 3. In the Set ID pop-up window, use the Left/Right arrows to select the appropriate Set ID number. Then, press ENTER.
Audio Setup Options Auto Volume / Clear Voice II / Balance Auto Volume Each broadcasting station has its own signal conditions, which may result in different volume levels for different programs/ channels. This option enables the STB1000 to make automatic adjustments to maintain a consistent volume level between channels. It also ensures a consistent volume level whether you are watching a commercial or a regular TV program.
Audio Setup Options (Cont.) Sound Mode Sound Mode This feature enables you to select a preset Sound Mode option and/or customize sound settings manually. 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the AUDIO menu option. Then, press ENTER.
Audio Setup Options (Cont.) Audio Reset / TV Speaker / Secondary Audio Program (SAP) Setup Audio Reset 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the AUDIO menu option. Then, press ENTER. AUDIO • Level 3 Balance 0 ? All audio settings will be reset. Sound ModeContinue? : Standard Enter - + L R • SRS TruSurround XT: Off 2. Use the Up/Down arrows to select the Reset option under Sound Mode, and then press ENTER.
Time Setup Options Set the STB Clock / STB On and Off Time Settings Set the STB Clock TIME The STB1000 clock is set automatically from a digital channel signal. The signal includes clock information provided by the broadcasting station. You can also set the clock manually if the auto clock function does not set the current time correctly. Move Enter Clock 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the TIME menu option. Then, press ENTER.
Time Setup Options (Cont.) Sleep Timer Sleep Timer 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the TIME menu option. Then, press ENTER 2. Use the Up/Down arrows to select Sleep Timer, and then press ENTER. 3. In the Sleep Timer pop-up window, use the Up/Down arrows to select the desired number of minutes before the STB/display automatically turns OFF. Then, press ENTER. 4.
Lock Setup Options Lock System Overview / Enable or Disable the Lock System Lock System Overview Parental Control can be used to block individual channels, programs with specific ratings or in specific categories, and external viewing sources. It is also possible to block all program viewing for a time period. The Parental Control function (V-Chip) blocks program viewing based on the ratings guidelines provided by broadcasting stations.
Lock Setup Options (Cont.) Set Password / Channel Blocking Set Password LOCK Use the following procedure to set a new password for the Lock System. Lock System Move Enter : Off Set Password 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the LOCK menu option. Then, press ENTER. Block Channel Movie Rating TV Rating-Children 2. If prompted for it, enter the Lock System password. TV Rating-General New ● ● ● ● 3.
Lock Setup Options (Cont.) Movie Rating / TV Rating-Children Movie Rating (MPAA) (for USA) This option blocks movies according to movie ratings limits. You can set the ratings limit by blocking out all movies with ratings above a specified level. Note that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas. 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the LOCK menu option. Then, press ENTER.
Lock Setup Options (Cont.
Lock Setup Options (Cont.) TV Rating-English / TV Rating-French TV Rating-English (for Canada) This option blocks TV programs based on the Canadian English rating system. LOCK Lock System Move : Off Set Password 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the LOCK menu option. Then, press ENTER. Blocking off : Permits all programs Block Channel E TV Rating-English C TV Rating-French 2. If prompted for it, enter the Lock System password.
Lock Setup Options (Cont.) Downloadable Rating / Input Block Downloadable Rating 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the LOCK menu option. Then, press ENTER. LOCK Lock System Move : Off Set Password Block Channel Humor Movie Rating Sport Cruelty TV Rating-Children 2. If prompted for it, enter the Lock System password. TV Rating-General 3. Use the Up/Down arrows to select Downloadable Rating, and then press ENTER.
Input Settings Select the Input Source 1. Press MENU on the Installer Remote, and use the arrow navigation keys to select/highlight the INPUT menu option. Then, press ENTER. 2. Use the Up/Down arrows to select the appropriate input source (see descriptions below). Then, press ENTER. 3. Press MENU to return to TV viewing, or press RETURN to return to the previous menu level. Input Source • TV: Select to watch over-the-air, cable, and digital cable broadcasts.
Commercial Mode Setup Overview Overview This document describes how to set up the STB1000 for Commercial Mode either while in the Embedded b-LAN™ (EBL) module’s Pass-through Mode or its Free-To-Guest (FTG) Mode. Note: The b-LAN module is internal to the STB1000 and allows the institution head end equipment to communicate with the STB for configuration and control. The b-LAN module also comprises the data tuner required for Pro:Centric operation.
Commercial Mode Setup for Master STB1000 This section describes how to set up a Master STB1000 when the EBL is in Pass-through Mode. Note: Disconnect all Aux inputs. Under certain conditions, Auto Tuning (Channel Search) is disabled if there is an Aux input active. Note: Refer to “FTG Mode of Operation” on pages 58 to 61 for information on configuring/editing FTG Channel Map and Installer Menu settings for an individual STB1000 in FTG Mode. 1. Set Installer Menu items.
Commercial Mode Setup for Master STB1000 (Cont.) (Continued from previous page) 3. Run Auto Tuning (Channel Search). a) Search for all available analog and digital channels: Go to the Channel Menu, select the Auto Tuning option, and follow the onscreen instructions. b) Use the Channel Edit option in the Channel Menu to edit the channel lineup, as necessary, to include free to guest channels only. • Add/delete channels per your system requirements.
Installer Menu Use the Installer Menu to set up or change operational settings. Refer to the table starting on the next page for brief descriptions of Installer Menu items. More detailed descriptions follow the table listing. Accessing the Installer Menu 1. Make sure the STB1000/display panel is ON. 2. Using the Installer Remote, press MENU repeatedly until the on-screen setup menus lock up, and then press 9-8-7-6 + ENTER to access the Installer Menu.
Installer Menu (Cont.) Installer Menu Items 000 through 071 Menu Item Function Value Range Default Value Brief Description of Function and Comments 000 INSTALLER SEQ 0~3 0 Leave default set to 0. 001 POWER MANAGE 0~7 0 Sets number of hours of no activity before automatic shutoff. 002 AC ON 0/1 0 Set to 1 to enable Auto Turn ON when AC power is applied. 003 BAND/AFC 0~3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC 0 ~ 127, 255 255 Channel tuned when STB is turned ON.
Installer Menu (Cont.) Installer Menu Items 073 through 119 Menu Item 44 Function Value Range Default Value Brief Description of Function and Comments 0/1 0 If set to 1 and Channel Override is 0, “NOT AVAILABLE” message is displayed when directly accessing a channel not in the favorite Channel List. 073 CH NOT AVBLE 075 REVERT CH 0/1 0 If set to 1 and loss of MPI communication occurs, STB tunes to Start Channel. 078 UPN MSB 0 ~ 255 0 User programmable number, most significant byte.
Installer Menu (Cont.) Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu. 0 = 9876 2 = 1478 To translate an STB volume level to the Installer Menu value, use the following formula: 1 = 4321 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The Power Management function is for saving energy. If set to 0, Power Manage is Off.
Installer Menu (Cont.) 016 - EN TIMER (Enable On/Off Timers) * If set to 1, the Timer function is available to the end user and enabled continuously. Set to 0 to disable On/Off Timers. 035 - COMPPORT EN. (Computer Port Enable) Enable/disable STB HDMI 1 input jack. Set to 0 to disable HDMI1. Set to 1 to enable HDMI1. Note: Clock must be set in order to use timers. Note: This setting is ignored if item 093 RJP AVAILABLE is set to 1.
Installer Menu (Cont.) 070 - FOR. CH-TIME (Channel-Time Display Foreground Color) Set according to Color Chart: 0 = Black 1 = Blue 2 = Green 3 = Cyan 4 = Red 5 = Violet 6 = Yellow 7 = White Note: Applies only to “Channel Not Available” message if item 073 is set to 1 (enabled).If foreground color and background color are the same, the menu background will be transparent.
Installer Menu (Cont.) • 6 = Scaler Model RJPs: DVI Mode Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP, only digital video is expected via the HDMI cable. Analog audio is provided via separate cable, from the source, connected to an RJP AUDIO IN. If no analog audio cable is connected, tuner audio will be heard. Notes: See Reference section, “RJP Model List and Input Auto-sensing Hierarchy.
Adding Channel Label Icons / Custom Channel Labels (2-5-4 + MENU Mode) Editing/Adding Channel Icons and/or Labels If there is no pre-assigned icon, you can make a custom channel label of up to seven (7) characters to help identify a channel or network. If desired, channel labels can also be added in addition to a pre-assigned icon. You may also add labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs.
Cloning Overview / Clonable Menu Features IMPORTANT CLONING INFORMATION Use one of the following options to Learn and Teach the Master STB1000 Setup: • Using a USB memory device • Using a TLL-1100A clone programmer • Using a LT2002 clone programmer Before you begin cloning: Each option is described in further detail on the pages that follow. As you perform cloning procedures, be sure to complete each task as indicated. If a procedure or step is omitted or not performed completely, cloning may not work.
Cloning Procedures Learning / Teaching a Master STB1000 Setup using a USB Memory Device USB Cloning Notes • Read the IMPORTANT CLONING INFORMATION on page 50 before beginning any cloning procedures. • You may edit a filename as part of the Learning procedure; however, a file with edited contents will not be recognized. • It is not possible to clone a Master STB1000’s clock using a USB memory device. Either set a Target STB’s clock manually, or use the Auto Clock setting in the STB setup menus.
Cloning Procedures (Cont.) Learning / Teaching a Master STB1000 Setup using a TLL-1100A Clone Programmer Warning: Do not connect a clone programmer to the STB1000 MPI/GAME CONTROL port while the STB is in LodgeNet PPV Mode, as this will damage the clone programmer. Cloning is accomplished using the STB/clone programmer MPI ports for communication (see diagram). TLL-1100A Cloning Notes • Read the IMPORTANT CLONING INFORMATION on page 50 before beginning any cloning procedures.
Cloning Procedures (Cont.) Learning / Teaching a Master STB1000 Setup using a TLL-1100A Clone Programmer (Cont.) Learn Setup from Master STB1000 1. Ensure the Master STB1000 is set up completely and the EBL is in Pass-through Mode. 2. If an analog channel is not available, direct tune the Master STB1000 to an Aux source, or select an Aux source, such as AV-1, from the Input Menu. Then, plug one end of the MPI cable into the MPI port on the STB jack panel. 3. Turn ON the TLL-1100A. 4.
Cloning Procedures (Cont.) Learning / Teaching a Master STB1000 Setup using a TLL-1100A Clone Programmer (Cont.) Teach Master STB1000 Setup to Target STB1000 1. Ensure the Target STB1000 EBL is in Pass-through Mode, and then use the Installer Remote to enter the Target STB Installer Menu: Press MENU repeatedly until the on-screen setup menus lock up, and then press 9-8-7-6 + ENTER. 2. Set Installer Menu item 117 FACT DEFAULT to 001, and press ENTER. 3.
Cloning Procedures (Cont.) Learning / Teaching a Master STB1000 Setup using an LT2002 Clone Programmer Warning: Do not connect a clone programmer to the STB1000 MPI/GAME CONTROL port while the STB is in LodgeNet PPV Mode, as this will damage the clone programmer. Cloning is accomplished using the STB/clone programmer MPI ports for communication (see diagram). LT2002 Cloning Notes • Read the IMPORTANT CLONING INFORMATION on page 50 before beginning any cloning procedures.
Cloning Procedures (Cont.) Learning / Teaching a Master STB1000 Setup using an LT2002 Clone Programmer (Cont.) Learn Setup from Master STB1000 1. Ensure the Master STB is set up completely and the EBL is in Passthrough Mode. 2. If an analog channel is not available, direct tune the Master STB1000 to an Aux source, or select an Aux source, such as AV-1, from the Input Menu. Then, plug one end of the MPI cable into the MPI port on the STB jack panel. 3.
Cloning Procedures (Cont.) Learning / Teaching a Master STB1000 Setup using an LT2002 Clone Programmer (Cont.) Teach Master STB1000 Setup to Target STB1000 1. Ensure the Target STB1000 EBL is in Pass-through Mode, and then use the Installer Remote to enter the Target STB Installer Menu: Press MENU repeatedly until the on-screen setup menus lock up, and then press 9-8-7-6 + ENTER. 2. Set Installer Menu item 117 FACT DEFAULT to 001, and press ENTER. 3.
FTG Mode of Operation FTG Configuration Overview The following steps outline local FTG configuration of individual STB1000s. Since these models are equipped with the EBL module, they can also be broadcast configured in FTG Mode by a Free-To-Guest Management Appliance (FMA) head end device. Refer to the Free-To-Guest (FTG) Configuration Application manual and/or the Installation & Setup manual for the FMA device for further information.
FTG Mode of Operation (Cont.) Determining the STB Operating Mode / FTG Channel Map Configuration Utility Overview To determine the operating mode of the STB1000, press MENU on the Installer Remote. If the end user Function Menu (showing aspect ratio options) appears, the STB EBL is in FTG Mode. If the STB setup menus appear, the EBL is in Passthrough Mode.
FTG Mode of Operation (Cont.) FTG Channel Map Configuration Utility / FTG Channel Map Editor Overview The FTG Channel Map Editor shows a single Logical Channel’s Data and the FTG Channel Map. LOGICAL CHANNEL MAPPING Select a Logical Channel number, then assign it the RF, Major, and Minor channel numbers to complete the mapping. CUSTOM CHANNEL LABELS/ICONS Enter custom labels and select icons by name on menu or by number. DELETE Click to remove highlighted channel from FTG Channel Map.
FTG Mode of Operation (Cont.) FTG Installer Menu Configuration Utility Overview CONFIGURATION SETTINGS Select tabs for categories of Installer Menu items to set up STB. INSTALLER DEFAULTS Click to reset FTG Installer Menu items shown in the FTG Configuration Application to defaults. IR REMOTE ACCESS Toggle IR Remote Access to ON to obtain access to STB setup menus and Installer Menu. WRITE Click to transfer the FTG Installer Menu settings to the EBL.
Remote Jack Pack Connections & Setup Remote Jack Pack Setup RJP Available? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item 093 RJP AVAILABLE appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP AVAILABLE to 001). See Installer Menu detailed descriptions for further information. 093 RJP AVAILABLE 001 STB Connections Make these connections ONLY after Commercial Mode Setup and STB1000 Cloning procedures are complete.
External Equipment Setup Digital Audio Optical Connections / Component Connections Digital Audio Optical Connections 1. Connect an optical cable between the OPTICAL DIGITAL AUDIO OUT connector on the STB1000 jack panel and the digital audio input connector on the external Digital Audio Amplifier System. 2. Select the Optical Digital Audio input source on the amplifier. 3. If not already done, turn ON the STB/display panel and external equipment.
External Equipment Setup (Cont.) HDMI/DVI Connections / RGB Hookup to PC HDMI/DVI Connections LAN 3. If not already done, turn ON the STB/display panel and external equipment. 4. Select the appropriate HDMI/DVI input source on the STB using the INPUT button on the Installer Remote or via the STB Input Menu. PR ..... .... REMOTE CONTROL OUT STB1000 Jack Panel R L AUDIO VIDEO RJP INTERFACE HMDI Cable ..... ..... ..... PB Y DISPLAY CONTROL AUDIO (RGB/DVI) RGB(PC) RGB IN 1(DVI) ..........
External Equipment Setup (Cont.) Composite Connections Composite Connections LAN DIGITAL VIDEO IN 2 .......... Y AUDIO (RGB/DVI) RGB(PC) ............... PR PB DISPLAY CONTROL ......... REMOTE CONTROL OUT STB1000 Jack Panel R L AUDIO VIDEO RJP INTERFACE SPEAKER OUT 8 UPDATE AV IN 1 1(DVI) .......... OPTICAL DIGITAL AUDIO OUT MPI/GAME CONTROL TV-LINK CFG RESET RGB IN 1.
Reference: Upgrading STB Software using a USB Memory Device Checking the Software Versions Note: This function is not accessible while the TV is in FTG or PPV Mode. You can check the software versions of the STB by accessing the Installer Menu with the Installer Remote: Press MENU repeatedly until the on-screen setup menus lock up, and then press 9-8-7-6 + ENTER. When you are finished, press ENTER again to exit the Installer Menu.
Reference: Downloading a Splash Screen using a USB Memory Device Splash Screen Image File Guidelines • The splash screen image must be a 24-bit (RGB 8 x 8 x 8) BMP. • The image should be no larger than 3 MB. • The ideal resolution for the image is 1366 x 768 pixels. • The image file must be stored in a folder named “LG_DTV” in the root directory of USB memory device. • Ensure the USB device has been formatted with FAT format. Downloading a Splash Screen Image 1. Turn the TV ON. 2.
Reference: RS-232 Display Panel Requirements DISPLAY CONTROL RS-232 Pin Configuration (DB9 Male) Pin Number Description 1 No Connection 2 RXD (Receive Data) 3 TXD (Transmit Data) 4 No Connection 5 GND 6 No Connection 7 No Connection 8 No Connection 9 No Connection 1 2 3 4 5 6 7 8 9 LG monitors/displays listed below require an RS-232 serial null-modem DB9 cable with female connectors at each end.
Reference: Display Panel Type Specifications The following table identifies the Installer Menu item 113 PANEL TYPE setting for each of the compatible monitors/TVs listed in the “RS-232 Display Panel Requirements” Reference.
Reference: STB1000 Aux Input Configuration ENABLE DIRECT ACCESS Tuning STB Installer Menu MPI DATA MPI DATA STATUS TYPE 0x41 SOURCES ENABLED (R/W) DATA STATUS TYPE 0xD2 CURRENT AV SOURCE (R) DATA STATUS TYPE 0x0D AUX SOURCE (R) START AUX SOURCE ASSIGNMENT OLD_ OCV = 0 OLD_ OCV = 1 Source Input Source Mode Number Labeling Value Labeling Value Labeling 130 90 Video2 (Side) CV 34 CAMPORT_EN 0x01 Video Front (Camport) 0 Video Front (Camport) 0 (VIDEO) 2 131 91 Video1 (Rear) CV
Reference: STB1000 Camport Auto Sense Operation The Camport Auto Sense function is enabled when: 1. Installer Menu item 034 CAMPORT EN is set to 1 AND 2. Installer Menu item 040 AUTO CAMPORT is enabled (1). Selectable: Can be accessed with INPUT key, direct access, etc. Auto Sense: STB switches to this input when connector is inserted. The Camport (AV IN 2 Video) has the highest priority and will override any commands including tuning to the Start Channel.
Reference: b-LAN Setup & Overview The b-LAN module is internal to the STB1000. It allows the hotel/institution head end equipment to communicate, via the institution’s RF distribution system, with the STB1000 for configuration and control. The b-LAN module also comprises the data tuner required for Pro:Centric operation. Power to the b-LAN module is controlled by Installer Menu item 118 POWER SAVINGS. The default value is 003—the b-LAN module is only powered when the STB is turned ON. See chart below.
Reference: RJP Model List and Input Auto-sensing Hierarchy RJP Model List Legacy Models Scaler Models RJP-101M RJP-201M RJP-101ML N/A RJP-110F N/A RJP-110FW N/A RJP-110W N/A RJP-110WBR N/A RJP-110S N/A RJP-120G N/A RJP-120T N/A RJP-201B RJP-301B, RJP-401W RJP-202B N/A RJP Input Auto-sensing Hierarchy 206-4147 Priority Video Audio 1st (Highest) Digital Video In Audio In (3.
Reference: Programming the Installer Remote The Installer Remote can be programmed to operate most remote-controllable devices. Note that the Installer Remote may not control all models of other brands. 1. Test the remote to find out whether it can operate other components without programming. For example, turn ON a component such as a DVD player, and press the corresponding Mode button (DVD) on the remote, while pointing at the component.
Reference: Remote Control Codes VCR Codes Brand Code(s) Brand Code(s) Brand Code(s) AIWA 034 LLOYD 034 RUNCO 148 AKAI 016, 043, 046, 124, 125, 146 LXI 003, 009, 013, 014, 017, 034, 101, 106 SALORA 014 SAMSUNG AMPRO 072 MAGIN 040 ANAM 031, 033, 103 MAGNAVOX 031, 033, 034, 041, 067, 068 032, 040, 102, 104, 105, 107, 109, 112, 113 115, 120, 122, 125 SANSUI 022, 043, 048, 135 012, 031, 033, 067, 069 SANYO 003, 007, 010, 014, 102, 134 AUDIO DYNAMICS 012, 023, 039, 043 BROKSONIC
Reference: Remote Control Codes (Cont.
Reference: IR Codes Remote Control Connection Connect your wired remote control to the REMOTE CONTROL OUT port on the STB1000 jack panel. Remote Control IR Codes Output Waveform Single pulse, modulated with 37.
Reference: IR Codes (Cont.
Troubleshooting General Troubleshooting Some Quick and Easy Tips for Resolving Problems Symptom Possible Cause(s) Possible Solution(s) Channel not included in channel lineup in internal STB controller (PTC). After 2-5-5 + MENU, only channels included in STB PTC will appear. If channel is available, it can be added to channel lineup. If it is not available, the “No Signal” message appears on the display screen. Software Problems Cannot direct enter channel number or “No Signal” appears.
Troubleshooting (Cont.) Troubleshooting Flow Chart Controller Quick Check STB conected to AC Power? No Plug into AC Power outlet. Yes STATUS LED on front of STB blinking? No Bad STB Yes Press POWER on Installer Remote. POWER LED on front of STB lit? No Check the IR connection on the STB. Press VOLUME UP/ DOWN or MUTE key on LG Installer Remote. Yes Display panel ON? Yes 1. Make sure the display panel is plugged in to the STB. No STB responded? No Bad STB 2.
Troubleshooting (Cont.) Commercial Mode Check / FTG Operation Troubleshooting Commercial Mode Check Press POWER on Installer Remote. STB responded? No Bad STB Yes Leave the STB ON. Go to Installer Menu by pressing MENU until the on-screen setup menus lock up (i.e., stop responding). STB stopped responding or continued to respond? Stopped responding STB is in Commercial Mode. Continued to respond STB is not in Commercial Mode. Call Technical Support for assistance.
Troubleshooting (Cont.) Clone Programmer Troubleshooting Warning: Do not connect a clone programmer to the STB1000 MPI/GAME CONTROL port while the STB is in LodgeNet PPV Mode, as this will damage the clone programmer. Reset Clone Programmer After Static Shock After replacing exhausted batteries (LT2002 only), or if the clone programmer behaves strangely after a static shock: • TLL-1100A: Turn the TLL-1100A OFF and then ON.
Specifications Dimensions Height: 1.77 inches (45 mm) Width: 13.875 inches (352.42 mm) Depth: 9.72 inches (247 mm) Weight: 6.4 pounds (2.
Glossary of Terms A list of definitions for some of the words found in this guide. 75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire through the middle. It screws onto the Antenna/Cable threaded jack on the back of the TV. 300 TO 75 OHM ADAPTER A small device that connects a 2-wire 300 ohm antenna to a 75 ohm RF jack.
Document Revision History / Notes Document Revision History Date Description February 2011 Revision A: New document Product documentation is available online at: www.LGsolutions.com/products. From the Products page, select TVs, Systems & Solutions, then Interface / Control Boxes & Cards, then STB1000. Click the Literature & Downloads tab at the bottom of the STB1000 page, and select the required document(s) from the Downloads list.
LG STB1000 HD Commercial Interface STB Warranty Broadcast Products Welcome to the LG family! We believe that you will be pleased with your new STB1000 HD Commercial Interface STB. Please read this warranty carefully, it is a “LIMITED WARRANTY” as defined under Federal Law. This warranty gives you specific legal rights, and you may also have other rights that vary from state-to-state within the U.S.A. LG’s RESPONSIBILITY Warranty Term One year parts and labor from date of purchase or delivery date.