PRODUCT OVERVIEW ENGLISH PRODUCT OVERVIEW Parts Controller Glass-ceramic Cooktop Gasket Rack Oven door Warming drawer / Storage drawer Accessories Included Accessories Standard Rack - LRE3061/LRE3193 (2ea) - LRE3083 (3ea) Spray bottle (1ea) Non-scratch scouring pad (1ea) Optional Accessories Grid 9 Broiler pan NOTE •• Contact LG Customer Service at 1-800-243-0000 (1-888-542-2623 in Canada) if any accessories are missing.
10 INSTALLATION INSTALLATION Installation Overview Please read the following installation instructions first after purchasing this product or transporting it to another location.
INSTALLATION 11 If you did not receive an anti-tip bracket with your purchase, call 1-800-243-0000 (1-888-542-2623 in CANADA) to receive one at no cost. Warning Warning Tip - Over Hazard •• The information in this manual should be followed exactly. Failure to do so may result in fire, electrical shock, property damage, personal injury, or death. A child or adult can tip the range and be killed. Verify the anti-tip bracket has been installed.
12 INSTALLATION Installing the Range Unpacking and Moving the Range CAUTION •• You should use two or more people to move and install the range. (Excessive Weight Hazard) Failure to do so can result in back or other injury. •• Do not use the door handles to push or pull the range during installation or when moving the range out for cleaning or service. Doing so can result in serious damage to the door of the range. Remove packing material, tape and any temporary labels from your range before using.
INSTALLATION 13 ENGLISH Dimensions and Clearances NOTE Save for the use of the local electrical inspector. 3" (7.6 cm) 24" (60.9 cm) Acceptable electrical outlet area 3" (7.6 cm) 25" (63.5 cm) Normal counter top depth Counter 36" (91.4 cm) top height Cabinet opening 24" (60.9 cm) 36" (91.4 cm) 29.8" (75.7 cm) A = 30" (76.2 cm) For U.S.A = 30" (76.2 cm) ~ 31" (78.
14 INSTALLATION Installing the Anti-tip Device Use a level to check your adjustments. Place the level diagonally on the oven rack, and check each direction for level. Warning Tip - Over Hazard First check direction . A child or adult can tip the range and be killed. Verify the anti-tip bracket has been installed. Ensure the anti-tip bracket is engaged when the range is moved. Do not operate the range without the anti-tip bracket in place.
INSTALLATION 15 •• Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that the range can be moved if servicing is ever necessary. •• The power supply cord and plug should not be modified. If it will not fit the outlet, have a proper outlet Installed by a qualified electrician. Use the cord/conduit connection plate to install the power cord or conduit. Leave the connection plate as installed for power cord installations.
16 INSTALLATION 3-Wire Connection : Power Cord 4-Wire Connection : Power Cord Warning Warning •• The middle (neutral or ground) wire, which is white, of a 3-wire power cord or a 3-wire conduit has to be connected to the middle post of the main terminal block. The remaining two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block. Failure to do so can result in electrical shock, severe personal injury or death.
INSTALLATION 17 4-Wire Connection: Conduit Install the conduit as follows: Remove the conduit connection plate from the rear of the oven and rotate it. The conduit hole (11/8") must be used. First, prepare the conduit wires as shown below. 3-Wire Conduit connection plate 4-Wire or Ground wire Second, install the conduit strain relief. For conduit installations, purchase a strain relief and insert it in the 11/8 in. (2.8 cm) conduit hole.
18 INSTALLATION Engaging the Anti-tip Device Test Run •• Move the range close enough to the opening to plug into the receptacle. Check if the range is properly installed and run a test cycle. •• Slide the range into position ensuring that the back leg slides under the anti-tip bracket. The range should sit flush against the back wall when properly installed. 1 Press Clear/Off to start test. 2 Turn on each burner to the Hi setting to check that the surface heating elements are working properly.