ENGLISH ESPAÑOL OWNER’S MANUAL AIR CONDITIONER Read this owner’s manual thoroughly before operating the appliance and keep it handy for reference at all times. TYPE: PORTABLE AIR CONDITIONER LP0820WSR LP1020WSR LP1220GSR LP1420BSR LP1420BHR www.lg.com Rev.00 Copyright © 2019 LG Electronics Inc. All Rights Reserved.
TABLE OF CONTENTS TABLE OF CONTENTS 3 SAFETY INSTRUCTIONS 19 MAINTENANCE 3 19 19 19 IMPORTANT SAFETY INSTRUCTIONS 7 PRODUCT OVERVIEW 7 Key Parts and Components Emptying the Water Collection Tank Cleaning the Case Cleaning the Air Filter 20 TROUBLESHOOTING 20 Before Calling for Service 8 INSTALLATION 8 9 9 10 10 11 11 12 13 15 Electrical Information Before Installing the Air Conditioner Wireless Remote Control Contents of Installation Kit Selection of Installation Location Assembling the Flexi
SAFETY INSTRUCTIONS 3 SAFETY INSTRUCTIONS Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and follow all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the safety alert symbol and either the word WARNING or CAUTION.
SAFETY INSTRUCTIONS When the power cord is to be replaced, replacement work shall be performed by authorized personnel only using only genuine replacement parts. . Connect to a properly rated, protected, and sized power circuit to avoid electrical overload. Always plug into a grounded outlet. Do not under any circumstances, cut or remove the third (ground) prong from the power cord. When installing or moving the appliance, be careful not to pinch, crush, or damage the power cord.
SAFETY INSTRUCTIONS GROUNDING INSTRUCTIONS The power cord of this appliance is equipped with a three-prong (grounding) plug. Use this with a standard three-slot (grounding) wall power outlet to minimize the hazard of electric shock. Have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded. DO NOT CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER PLUG.
SAFETY INSTRUCTIONS CAUTION To reduce the risk of minor or moderate injury to persons, malfunction, or damage to the product or property when using this product, follow basic precautions, including the following: INSTALLATION Take care when installing the product that exhaust or condensation does not damage nearby property. Follow installation instructions exactly to avoid excessive vibration or water leakage. OPERATION This appliance is not intended for use as a precision refrigeration system.
PRODUCT OVERVIEW 7 PRODUCT OVERVIEW ENGLISH Key Parts and Components temperature, and 10 WIRELESS REMOTE CONTROL The remote control allows you to adjust the temperature and operate most functions of the air conditioner from across the room. 11 7 9 7 using the bottom drain port. CONTINUOUS DRAIN PORT Connect a garden hose for continuous drainage when running the air conditioner in Dry mode.
INSTALLATION INSTALLATION WARNING Electrical Information Power cord may include a current interrupter device. TEST and RESET buttons are provided on the plug case. The device should be tested on TEST button and then the RESET button. If the TEST button does not trip or if the RESET button will not stay engaged, discontinue use of the air conditioner for 120 V RESET TEST This appliance should be installed in accordance with the National Electrical Code.
INSTALLATION 99 INSTALLATION Wireless Remote Control Before Installing the Air Conditioner If the display screen of the remote control begins to fade, replace the batteries. Insert AAA (1.5 V) batteries before using the remote control. 1 Remove the cover on the back of the remote control. 2 Insert the new batteries and make sure that the + and - terminals of the batteries are installed correctly.
INSTALLATION Contents of Installation Kit + + 1 Diffuser 1 Flexible vent hose 1 Mounting Bracket Flexible vent hose set 1 Panel A (18″) Window vent panel 1 Panel B (9″) Extension panel 1 Panel C (17″) Extension panel 1 Panel D (17″) Extension panel 2 Long adhesive foam seals 1 Non-adhesive foam seal 2 Short adhesive foam seals 2 Security brackets 4 Type A screws (1/2“) 4 Type B screws (3/4“) 1 Drain hose (on some models) 1 Lock nut (on some models) 1 Type C screw (5/16“) Selection of
INSTALLATION 11 Assembling the Flexible Vent Hose Set Pull evenly on the folds to extend one end of the flexible vent hose. 2 Insert the mounting bracket on to the end of the vent hose, aligning the mounting bracket threads with the notch on the flexible vent hose. 3 Turn the mounting bracket counterclockwise though 5 rotations or until the flexible vent hose is firmly attached. 4 Repeat the process to attach the diffuser to the other end of the flexible vent hose.
INSTALLATION Window Vent Panel and Extensions The window installation kit allows you to install the air conditioner in most vertical-sliding windows 18″ to 50″ wide, or horizontal-sliding windows from 18″ to 50″ high. Panel Window opening 18″ 19″ - 26″ 27″ - 34″ 35″ - 50″ A 18″ √ √ √ √ B 9″ C 17″ D 17″ √ √ Panel B (9″) Fig. √ √ a b c d 1. Select the panels required based on the window opening, as shown above. 2.
INSTALLATION 13 Installing Vent Panels ENGLISH Long adhesive foam seal ↓ Short adhesive foam seal ↓ Short adhesive foam seal ↓ ↑ Long adhesive foam seal Attach the long adhesive foam weather seals to the top and bottom sides of the window vent panel assembly. Attach the short foam weather seals to the right and left sides of the panel assembly. (Attaching the foam weather seals to the panel assembly rather than the window sash and frame makes for easier cleanup when removing the panel assembly.
INSTALLATION 14 Type C screw Slot (1) Insert (2) Slide 5 Align the tabs on the diffuser with the slots in the vent panel. Insert the diffuser into the opening in the vent panel and slide the diffuser all the way over to lock the tabs in place. Position the diffuser with the round opening above the bottom of the vent panel to avoid interference from the window sill. 6 Insert the type C screw in the hole in the diffuser to prevent the diffuser from sliding out of the vent opening.
INSTALLATION 15 Drain Hose Installation for Heating (On Some Models) • If you use the Heat mode, you must install the drain hose. If only the Cool mode is used, the drain hose is not needed. • If the outside temperature is at or near freezing 32 °F (0 °C) follow the indoor drainage instructions. • When the weather is above freezing, the unit can be set up to drain to the outside. Make sure the outlet of the hose is aimed away from nearby surfaces that could be stained or damaged by the draining water.
INSTALLATION Outdoor Drainage 1. To attach the drain hose, insert the connector into the pump drain port at the back of the unit until it snaps into place. 2. Unscrew the nut at the bottom of the locking nut. Insert the locking nut into the hole in the front of the window vent panel and reassemble the nut. Unscrew the top part of the locking nut until you can easily insert the drain hose through the opening. 3. Make sure to insert the drain hose at least 8 inches (20 cm). 4.
OPERATION 17 OPERATION 8 1 2 ENGLISH Control Panel and Remote Control 6 3 1 4 Power ( 5 ) Turns the air conditioner on and off. A chime sounds to confirm you have turned it on or off. 2 2 4 7 5 6 1 3 Mode Press this button repeatedly to toggle through and select the operating mode. Modes include Cool, Dry (dehumidify), Fan, and Heat. An LED illuminates to indicate the selected mode. The default mode is Cool. Cool ( ) Compressor runs and cools the room.
3 4 OPERATION Temperature Control ∧/∨ 6 This function automatically moves the louvers to adjust the direction of the air flow. Press the Auto Swing button repeatedly to select the desired direction. NOTE • To switch the temperature units on the display between Fahrenheit (°F) and Celsius (°C), press and hold the ∧ and ∨ buttons on the control panel at the same time for 5 seconds.
MAINTENANCE MAINTENANCE Before cleaning or performing maintenance, unplug the product and wait until the fan stops. Emptying the Water Collection Tank When the internal water collection tank is full, the LED display will show FL and the air conditioner will turn off until the tank is emptied. • Unplug the air conditioner, disconnect the exhaust hose from the back, and move the air conditioner to a suitable drain location or outdoors.
TROUBLESHOOTING TROUBLESHOOTING Before Calling for Service The appliance is equipped with an automatic error-monitoring system to detect and diagnose problems at an early stage. If the appliance does not function properly or does not function at all, check the following before you call for service. Problem Possible Cause Solutions The air conditioner is unplugged. Make sure the air conditioner plug is pushed completely into the outlet. The fuse is blown/circuit breaker is tripped.
TROUBLESHOOTING Problem Possible Cause 21 Solutions The cooling coils are iced over. Water collects in base pan. Moisture removed from air and drains into base pan. This is normal for a short period in areas with little humidity; normal for a longer period in very humid areas. Outside temperature extremely hot. Refer to installation instructions or check with installer. Air movement sound. This is normal. If too loud, adjust the fan speed to low. Remote control not located within range.
WARRANTY WARRANTY WHAT THIS WARRANTY COVERS: LG Electronics U.S.A., Inc. (“LG”) warrants your LG Portable Air Conditioner ("product") against defect in materials or workmanship under normal household use, during the warranty period set forth below, LG will, at its option, repair or replace the product.
WARRANTY 23 Product where the original factory serial numbers have been removed, defaced or changed in any way. Repairs when product is used in other than normal and usual household use (e.g. rental, commercial THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING AND WITHOUT LIMITATION TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
WARRANTY ARBITRATION NOTICE: THIS LIMITED WARRANTY CONTAINS AN ARBITRATION PROVISION THAT REQUIRES YOU AND LG TO RESOLVE DISPUTES BY BINDING ARBITRATION INSTEAD OF IN COURT, UNLESS YOU CHOOSE TO OPT OUT. IN ARBITRATION, CLASS ACTIONS AND JURY TRIALS ARE NOT PERMITTED. PLEASE SEE THE SECTION TITLED “PROCEDURE FOR RESOLVING DISPUTES” BELOW.
ESPAÑOL ESPAÑOL MANUAL DEL PROPIETARIO AIRE ACONDICIONADO Lea detenidamente el manual del propietario antes de poner el electrodoméstico en funcionamiento y consérvelo a mano en todo momento para su referencia. TIPO: AIRE ACONDICIONADO PORTÁTIL LP0820WSR LP1020WSR LP1220GSR LP1420BSR LP1420BHR www.lg.com Copyright © 2019 LG Electronics Inc. Todos los Derechos Reservados.
2 TABLA DE CONTENIDOS TABLA DE CONTENIDOS 3 INSTRUCCIONES DE SEGURIDAD 3 INSTRUCCIONES IMPORTANTES DE SEGURIDAD 7 DESCRIPCIÓN GENERAL DEL PRODUCTO 7 Piezas y componentes clave 8 INSTALACIÓN 8 9 Información eléctrica Antes de instalar el aire acondicionado 9 Control remoto inalámbrico 10 Contenido del kit de instalación 19 MANTENIMIENTO 19 Cómo vaciar el tanque de recolección de agua 19 Cómo limpiar la cubierta 19 Cómo limpiar el filtro de aire 20 SOLUCIÓN DE PROBLEMAS 20 Antes de ll
INSTRUCCIONES DE SEGURIDAD 3 INSTRUCCIONES DE SEGURIDAD LEA TODAS LAS INSTRUCCIONES ANTES DE UTILIZAR Su seguridad y la de los demás son muy importantes. Tanto en este manual como en el equipo, hemos proporcionado muchos mensajes de seguridad importantes. Siempre debe leer y respetar todos los mensajes de seguridad. ADVERTENCIA Podría sufrir lesiones graves o la muerte si no sigue las instrucciones. PRECAUCIÓN Puede resultar lesionado o causar daño al producto si no sigue las instrucciones.
4 INSTRUCCIONES DE SEGURIDAD Cuando sea necesario sustituir el cable de alimentación, el trabajo de sustitución deberá realizarlo personal autorizado utilizando únicamente piezas de repuesto originales. El trabajo de instalación debe realizarlo el estándar estadounidense National Electrical Code (NEC). protegido para evitar la sobrecarga eléctrica. Enchúfelo siempre a una toma conectada a tierra. No corte ni quite la tercera clavija (tierra) del enchufe del cable de alimentación bajo ninguna circunstancia.
INSTRUCCIONES DE SEGURIDAD 5 Si entra agua en el producto, interrumpa la alimentación del circuito principal y, a continuación, desenchufe el producto y llame al servicio técnico. Si el producto se ha mojado accidentalmente, comuníquese con el Centro de Información al Cliente de LG Electronics para que le den instrucciones antes de reanudar el uso. Desenchufe el producto si no se va a utilizar durante períodos largos. Desenchufe el producto antes de limpiar.
6 INSTRUCCIONES DE SEGURIDAD PRECAUCIÓN Para reducir el riesgo de lesiones leves o moderadas a personas, el mal funcionamiento o daño al producto o propiedad cuando use este producto, siga las precauciones básicas, incluido lo siguiente: INSTALACIÓN Al instalar el producto, tenga cuidado de que los gases de escape o la condensación no produzcan daños materiales a su alrededor. Siga escrupulosamente las instrucciones de instalación para evitar vibraciones excesivas o fugas de agua.
DESCRIPCIÓN GENERAL DEL PRODUCTO 7 DESCRIPCIÓN GENERAL DEL PRODUCTO Piezas y componentes clave LA TRANSPIRACIÓN DEL AIRE ESPAÑOL ESPAÑOL La dirección del aire se puede controlar adondequeiera que usted necesite frescar por adjustar la lumbrera horizontal. Ajustar arriba y abajo la lumbrera horizontal va a cambiar el fluido vertical. MANIJAS INTEGRADAS Las asas integradas proporcionan un agarre conveniente al levantar el aire acondicionado.
8 INSTALACIÓN INSTALACIÓN ADVERTENCIA Información eléctrica El cable de alimentación puede incluir un interruptor de corriente. En la carcasa del enchufe hay un botón de TEST (prueba) y otro de RESET (restablecer). El dispositivo debe probarse periódicamente pulsando en primer lugar el botón TEST y, a continuación, el botón RESET.
INSTALACIÓN Antes de instalar el aire acondicionado 9 Control remoto inalámbrico Inserción de las baterías Si la pantalla del control remoto comienza a hacerse tenue, cambie las baterías. Coloque baterías AAA (1.5 V) antes de utilizar el control remoto. Quite la tapa de la parte posterior del control remoto. 2 Coloque las baterías nuevas y asegúrese de que los polos + y - estén ubicados correctamente. ESPAÑOL ESPAÑOL 1 NOTA El acondicionador de aire incluye pilas nuevas para el control remoto.
10 INSTALACIÓN Contenido del kit de instalación + + 1 Difusor 1 Manguera flexible de ventilación 1 Soporte de montaje Conjunto de manguera Flexible de ventilación 1 Panel A (18″) Panel de ventilación de ventana 1 Panel B (9″) Panel de extensión 1 Panel C (17″) Panel de extensión 1 Panel D (17″) Panel de extensión 2 Sellos de espuma adhesiva largos 1 sello de espuma no adhesiva 2 Soporte de seguridad 4 Tornillos tipo A (1/2“) 1 Manguera de drenaje (en algunos modelos) 1 Tuerca fija (en algun
INSTALACIÓN 11 Ensamblando el conjunto de manguera flexible de ventilación Para desenvolver el extremo de la Manguera flexible de ventilación se ha doblado. 2 Inserte el soporte de montaje en el extremo del manguera flexible de ventilación, alineando los hilos soporte de montaje con la muesca del manguera flexible de ventilación. 3 Gire la soporte de montaje en sentido contrario a las agujas del reloj mediante 5 rotaciones o hasta que el manguera flexible de ventilación esté firmemente sujeto.
12 INSTALACIÓN Panel de ventilación y extensiones de la ventana El kit de instalación de la ventana permite que usted instale los acondicionadores de aire en la mayoría de las ventanas vertical-que resbalan 18″ a 50″ de par en par, o las ventanas del marco-estilo a partir del 18″ a 50″ arriba. Panel A 18″ Longitud de la ventana. 18″ √ 19″ - 26″ √ 27″ - 34″ √ 35″ - 50″ √ Panel B (9″) B 9″ C 17″ D 17″ √ √ √ √ Fig. a b c d 1.
INSTALACIÓN 13 INSTALACIÓN 13 Instalación de paneles de ventilación Sello de espuma adhesiva largos ↓ sello de espuma adhesiva cortos ↓ Panel de extensión (si fuera necesario) ESPAÑOL ESPAÑOL sello de espuma adhesiva cortos ↓ Panel de ventilación ↑ Sello de espuma adhesiva largos Coloque los burletes de espuma adhesiva largos en los lados superior e inferior del ensamblaje del panel de ventilación de la ventana.
INSTALACIÓN 14 Tornillos tipo C Muesca (1) Inserte (2) Deslice 5 Alinee las pestañas del difusor con el muescas en el panel de ventilación. Inserte el difusor en la abertura del panel de ventilación y deslice el difusor completamente hacia adentro para bloquear las pestañas en su lugar. Coloque el difusor con la abertura redonda sobre la parte inferior del panel de ventilación para evitar la interferencia del alféizar de la ventana.
INSTALACIÓN 15 Instalación de la manguera de drenaje para calefacción (en algunos modelos) PRECAUCIÓN Drenaje interior 1. Para adherir la manguera de drenaje, inserte el conector al puerto de drenaje de bomba en la parte trasera de la unidad hasta que éste encaje en su lugar. 2. Coloque el otro extremo de la manguera de drenaje en un balde que contenga al menos 28 onzas. Recuerde revisar y vaciar el balde frecuentemente para evitar desbordes. 3.
16 INSTALACIÓN Drenaje exterior 1. Para adherir la manguera de drenaje, inserte el conector al puerto de drenaje de bomba en la parte trasera de la unidad hasta que éste encaje en su lugar. 2. Destornille la tuerca en la parte inferior de la contratuerca. Inserte la contratuerca en el orificio en la parte frontal del panel de ventilación de la ventana y vuelva a ensamblar la tuerca.
FUNCIONAMIENTO 17 FUNCIONAMIENTO Panel de control y control remoto 8 6 ESPAÑOL ESPAÑOL 1 2 3 1 Encendido ( 4 5 ) Enciende y apaga el acondicionador de aire. Al encender, se oira una senal sonora ascendente para confirmar. 2 2 4 7 5 6 1 3 Mode (Modo) Presione este botón repetidamente para alternar y seleccionar el modo operativo. Los modos incluyen Cool (Refrigeración), Dry (Secar)(Deshumidificador), Fan (Ventilador), y Heat (Calefacción).
18 3 4 FUNCIONAMIENTO Control de temperature Ʒ/Ƹ Auto Swing (Balanceo) Esta función mueve automáticamente las paletas para ajustar la dirección del flujo de aire. Presione el botón Auto Swing(Balanceo) repetidamente para seleccionar la dirección deseada. NOTA • Para cambiar las unidades de temperatura en la pantalla entre Fahrenheit (°F) y Celsius (°C), mantenga presionados los botones Ʒ y Ƹen el panel de control al mismo tiempo durante 5 segundos.
MANTENIMIENTO MANTENIMIENTO ADVERTENCIA Antes de limpiar o realizar el mantenimiento, desenchufe el producto y espere hasta que el ventilador se detenga. Cuando el tanque interno de recolección de agua está lleno, la pantalla LED mostrará FL y el aire acondicionado se apagará hasta que el tanque se vacíe. • Desconecte el aire acondicionado y la manguera de escape de la espalda, y mueva el aire acondicionado a un lugar adecuado de drenaje o al aire libre.
20 SOLUCIÓN DE PROBLEMAS SOLUCIÓN DE PROBLEMAS Antes de llamar al servicio técnico El artefacto está equipado con un sistema automático de monitoreo de errores para detectar y diagnosticar problemas en una etapa temprana. Si el artefacto no funciona adecuadamente o si no funciona en absoluto, Problema Causa posible El aire acondicionado está desenchufado. El fusible se ha fundido o el disyuntor se ha activado. El acondicionador de aire no se inicia. Interrupción del suministro eléctrico.
SOLUCIÓN DE PROBLEMAS Problema Causa posible Las bobinas de enfriamiento se han helado. Se acumula agua en la bandeja base. La humedad eliminada del aire se acumula en la bandeja base. El acondicionador de aire se enciende y apaga rápidamente. Filtro de aire sucio: aire limitado. Hay ruido cuando la unidad enfría. El sensor remoto se desactiva prematuramente. La habitación está demasiado fría. Soluciones aire e impedir que el acondicionador de aire enfríe adecuadamente la habitación.
22 GARANT ÍA GARANTÍA COBERTURA DE LA GARANTÍA: LG Electronics Inc. ("LG") garantiza que reparará o sustituirá, gratuitamente, su producto si resulta defectuoso en materiales o mano de obra bajo condiciones normales de uso durante el periodo de garantía mencionado más abajo, efectivo a partir de la fecha de compra del producto original por parte del consumidor.
GARANT ÍA 23 Los productos cuyos números de serie de fábrica originales hayan sido quitados, borrados o cambiados de ninguna manera. Las reparaciones cuando el producto se utiliza para cualquier cosa fuera de lo normal y del uso doméstico instrucciones que se indican en el manual del propietario. La extracción y reinstalación del producto si está instalado en un lugar inaccesible.
24 GARANT ÍA AVISO DE ARBITRAJE: ESTA GARANTÍA LIMITADA CONTINE UNA CLÁUSULA DE ARBITRAJE QUE LE DEMANDA A USTED Y A LG RESOLVER CONFLICTOS A TRAVÉS DE UN ARBITRAJE VINCULANTE EN LUGAR DE HACERLO EN LA CORTE, A MENOS QUE USTED DECIDA NO PARTICIPAR. EN EL ARBITRAJE NO ESTÁN PERMITIDAS LAS ACCIONES COLECTIVAS NI LOS JUCIOS CON JURADO. POR FAVOR, VEA A CONTINUACIÓN LA SECCIÓN TITULADA "PROCEDIMIENTO PARA RESOLVER CONFLICTOS".
LG Customer Information Center Centro de Información al Cliente de LG 1-800-243-0000 Register your product Online! Centro de Información al Cliente de LG LG Electronics Inc. 1000 Sylvan Ave., Englewood Cliffs, NJ 07632 www.lg.