9 COMPONENTS Refrigerator Interior (Freezer Swing Model) ENGLISH * Optional Parts : Not included with all models. Dairy Product Bin Used to preserve dairy products. LED interior lamps Fold-Up Bin The interior lamps light up the inside of the refrigerator. Can be folded up when tall storage is needed in the Door Bin. Adjustable Refrigerator Shelf The shelves in your refrigerator are adjustable to meet your individual storage needs.
INSTALLATION ENGLISH INSTALLATION Installation Overview it to another location.
11 INSTALLATION Specifications ENGLISH improvements. 24 cu. ft. models 32 3/4’’ (W) X 34 7/8’’ (D) X 69 7/8’’ (H), 62 ¾’’ (D w/ door open) 833.1 mm (W) X 886.4 mm (D) X 1775.5 mm (H), 1592.5 mm (D w/ door open) Dimensions 22 cu. ft. models 29 3/4’’ (W) X 34 7/8’’ (D) X 68 ½’’ (H), 59 ¾ (D w/ door open) 756.9 mm (W) X 886.4 mm (D) X 1739.9 mm (H), 1516.5 mm (D w/ door open) 24 cu. ft. models 248.5 lb. (112.7 Kg) – Freezer Drawer models 235.2 lb. (106.7 Kg) – Freezer Swing models 22 cu. ft.
INSTALLATION Unpacking Your Refrigerator Choosing the Proper Location . . Use two or more people to move and . install the refrigerator. Failure to do so can result in back or other injury. Your refrigerator is heavy. When moving the refrigerator for cleaning or service, the refrigerator straight out when moving it. Do not wiggle or walk the refrigerator . could occur. such as gasoline, away from the refrigerator.
13 INSTALLATION Ambient Temperature ENGLISH Install this appliance in an area where the temperature is between 55°F (13°C) and 110°F (43°C). If the temperature around the appliance is too low or high, cooling ability may be adversely affected. Removing/Assembling the Refrigerator Door Handles NOTE When it is necessary to move the refrigerator through a narrow opening, removing the doors is the recommended procedure. If it is necessary to remove the handles, follow the directions below.
INSTALLATION 14 Removing/Assembling the Doors and Drawers When it is necessary to move the refrigerator through a narrow opening, removing the doors is the recommended procedure. Removing the Handle 1 Loosen the set screws located on the 3 lower side of the handle with a /32 in. (2.5 mm) Allen wrench and remove the handle. 2 Loosen the mounting fasteners . that connect to the freezer drawer and handle using a 1/4 in. (6.35 mm) Allen wrench, and remove the mounting fasteners. . . .
15 INSTALLATION ENGLISH Removing the Refrigerator Door Assembling the Refrigerator Door 1 Remove the top hinge cover screws . Lift the hook (not visible), located at the bottom of the front side of the cover , with a flat-head screwdriver. 1 Make sure that the plastic sleeve is inserted in the bottom of the door. Lower the door onto the middle hinge pin as shown in the figure. 2 2 Remove the three bolts using a 10mm or 13/32-inch socket wrench and lift off the top hinge. Set parts aside.
INSTALLATION 4 Slide out the bar. ENGLISH Removing the Freezer Drawers (On Freezer Drawer Models) The top and bottom drawers are all removed in the same way. In the following figures, the Pullout Drawer located above the freezer drawer is not shown for clarity. WARNING . Use two or more people to remove and install the freezer drawer. Failure to do so can result in back or other injury. . Do not hold the handle when removing or replacing the drawer. The handle may come off, causing personal injury. .
17 INSTALLATION ENGLISH Assembling the Freezer Drawers (On Freezer Drawer Models) 3 Reinstall the bar in the drawer supports. 4 Lower the door into final position and tighten the screws located on both sides. 5 With the drawer pulled out to full extension, insert the lower basket in the rail assembly. The top and bottom drawers are all assembled in the same way. 1 2 Using two hands, pull out both rails simultaneously until they are fully extended.
INSTALLATION Assembling the Freezer Door (On Freezer Swing Models) Before beginning, make sure you completely remove the refrigerator door. 1 P lac e the f re e ze r door dow n on the bottom hinge pin. See Removing the Refrigerator Door (p.15) WARNING . Use two or more people to remove and Bottom Hinge Pin install the freezer door. Failure to do so can result in back or other injury. . When you lay the door down, be careful . Do not sit or stand on the freezer door. .
19 INSTALLATION Reversing Door Opening Direction ENGLISH 4 NOTE To assist in the installation of the handle on the right side, place a piece of masking tape near the top of the handle before removing it. The appearance of the handle may vary from what is shown in the illustrations. Reversing the Refrigerator Handle 1 Loosen the set screws with a 3/32 in. (2.5 mm) Allen wrench and remove the handle. 2 Loosen the mounting fasteners that connect to the refrigerator door and handle using a 1/4 in. (6.
INSTALLATION 20 4 Remove the four screws , the hinge and the hinge pin brackets pin insert from the bottom right side of the door. 1 2 3 1 Remove the top hinge cover screws . Lift the hook (not visible), located at the bottom of the front side of the cover , with a at-head screwdriver. 3 5 Reinstall the hinge pin brackets 1 , screws 2 and hinge pin insert left side of the door. 3 on the bottom 2 Using a13/32 in. or 10 mm socket wrench, remove the three bolts and lift o the top hinge.
21 INSTALLATION 7 ENGLISH With a flat-head screwdriver, carefully pry off and remove the cover over the bolt holes on the left side of the refrigerator. 11 Insert the decorative screw into the outer hole on the right side of the flange. Attach the cover on the right side. Cover is forcefitted. Decorative Screw 8 9 10 Remove the outer lower decorative screw from the flange on the frame between the freezer and refrigerator doors. (You will need this hole for the middle hinge bracket.
INSTALLATION 22 NOTE 14 1 Remove the top hinge cover screws . Lift the hook (not visible), located at the bottom of the front side of the cover , with a flat-head screwdriver. 2 Using a 10mm or 13/32 in. socket wrench, remove the three bolts and lift off the top hinge. Set parts aside. Line up the left top hinge with the holes in the top of the refrigerator. Use the three bolts to replace the hinge. Assemble the left hinge cover with the two screws.
23 INSTALLATION 4 ENGLISH Remove the four screws 1 , the hinge pin insert 2 and the hinge pin brackets from the bottom right side of the door. NOTE 3 Before removing the freezer door, make sure you completely remove the refrigerator door. 6 3 Use a ¼ in. (6.35 mm) hex socket wrench to loosen the hinge pin 1 and remove it. Remove the two bolts 2 , the screw 3 and the hinge 4 . Remove the washer.
INSTALLATION 24 9 12 On th cap 1 and a pivot 2 . Remove them with on the opposite side ( the cap goes on the right and the pivot on the left). Screw Bolts 10 Remove the four screws 1 , the hinge pin brackets 2 and the hinge pin insert from the bottom right side of the freezer door. 3 3 11 Reinstall the hinge pin insert 1 , the hinge pin brackets 2 and the screws 3 on the bottom left side of the door. 3 13 Re move the decorative caps on the bottom of the refrigerator housing.
25 INSTALLATION 14 Using a 13/32 in. or 10 mm socket wrench ENGLISH with a 2 in. (50.8 mm) extension and a screwdriver, tighten the two bolts and the screw, and assemble the bottom hinge on the left side of the flange. 18 Flip the middle hinge bracket and position it on the left side of the refrigerator and reattach it with two bolts and a screw. 19 Place the freezer door down on the bottom 15 Attach the hinge pin using a ¼ in. (6.35 mm) socket wrench. hinge pin.
INSTALLATION 26 21 Insert the decorative screw into the outer hole on the right side of the flange. Attach the cover on the right side. Cover is forcefitted. NOTE Decorative Screw 24 Line up the left top hinge with the holes in the top of refrigerator. Use the three bolts to replace the the hinge. Assemble the left hinge cover with the two screws. 22 Loosen the two screws and remove the left hinge cap. 25 23 Place the refrigerator door down over the hinge pin on the middle hinge pin bracket.
27 INSTALLATION Connecting the Water Line (Ice maker installed only) ENGLISH Before You Begin This water line installation is not covered by the refrigerator warranty. Follow these instructions carefully to minimize the risk of expensive water damage. Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator WARNING Wear eye protection during installation to prevent injury.
INSTALLATION 28 . Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with a minimum inside diameter of 5/32 in. (4 mm) at the point of connection to the COLD WATER LINE. Saddle-type shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. 2 CHOOSE THE VALVE LOCATION Choose a location for the valve that is easily accessible.
29 INSTALLATION 5 ENGLISH TIGHTEN THE PIPE CLAMP Tighten the clamp screws until the sealing washer begins to swell. 8 NOTE: Do not overtighten the clamp or you may crush the tubing. Shut the water off at the water valve after about one quart of water has been flushed through the tubing. Washer Pipe Clamp FLUSH OUT THE TUBING Turn the main water supply on and flush out the tubing until the water is clear.
INSTALLATION 30 10 CAUTION Check to see if leaks occur at the water line connections. 11 PLUG IN THE REFRIGERATOR Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall. Push the refrigerator back to the wall. 12 START THE ICEMAKER Set the icemaker power switch to the ON position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (–9°C) or below.
31 INSTALLATION Leveling and Door Alignment ENGLISH Leveling Door Alignment After installing, plug the refrigerator’s power cord into a 3-prong grounded outlet and push the refrigerator into the final position. If the space between your doors is uneven, follow the instructions below to align the doors. Your refrigerator has two front leveling legs— one on the right and one on the left. Adjust the legs to alter the tilt from front-to-back or sideto-side.
HOW TO USE 32 Before use Clean the refrigerator. shipping. . . WARNING Do not scratch the refrigerator with a sharp object or use a detergent that or adhesive from the refrigerator. on the rear surface of the refrigerator. NOTE Remove adhesive residue by wiping it o with your thumb or dish detergent. Connect the power supply. Check if the power supply is connected before use. Read the “Turning On The Power” section. Turn off the icemaker if the refrigerator is not yet connected to the water supply.
33 HOW TO USE Control Pad ENGLISH * Depending on the model, some of the following functions may not be available. Control Pad Features LED Display Indicator Door Control Button Refrigerator Temperature Indicates the set temperature of the refrigerator compartment in Celsius (°C) or Fahrenheit (°F). Freezer Temperature Indicates the set temperature of the freezer compartment in Celsius (°C) or Fahrenheit (°F).
HOW TO USE 34 Automatic Icemaker (Freezer Room) ENGLISH (Ice maker installed only) * Depending on the model, some of the following functions may not be available. Ice is made in the automatic icemaker and sent to the dispenser. The icemaker will produce 12 cubes per cycle—approximately 100 cubes in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other operating conditions. . . .
35 HOW TO USE Automatic Icemaker (continued) ENGLISH . . . . . . . WARNING The first ice produced may include particles or odor from the water supply line or the water tank. Normal Sounds You May Hear . Throw away the first few batches of ice. This is also necessary if the refrigerator has not been used for a long time. If discolored ice is produced, check the water supply. If the problem continues, contact a qualified service center. Do not use the ice or water until the problem is corrected.
HOW TO USE 36 Storing Food ENGLISH Food Preservation Location (On Freezer Drawer Models) Store your food in the optimal space to enjoy the freshest taste. Adjustable refrigerator shelf Adjustable shelves to meet your individual storage needs. (Half or full Type) Vegetable storage (Crisper) Preserves vegetables and fruit.
37 HOW TO USE Food Preservation Location (On Freezer Swing Models) ENGLISH Store your food in the optimal space to enjoy the freshest taste. Adjustable refrigerator shelf Adjustable shelves to meet your individual storage needs. Vegetable storage (Crisper) Preserves vegetables and fruit. Glide‘N’Serve Used for large party trays, deli items and beverages Dairy product bin Door bin Store drinks such as juice and soda, as well as seasonings, salad dressings and other food items.
HOW TO USE 38 Food Storage Tips Wrap or store food in the refrigerator in airtight and moisture-proof material unless otherwise noted. This prevents food odor and taste transfer throughout the refrigerator. For dated products, check date code to ensure freshness. Food How to Butter or Margarine Keep opened butter in a covered dish or closed compartment. When storing an extra supply, wrap in freezer packaging and freeze. Cheese Store in the original wrapping until you are ready to use it.
39 HOW TO USE Storing Frozen Food (continued) ENGLISH Packaging Successful freezing depends on correct packaging. When you close and seal the package, it must not allow air or moisture in or out. If it does, you could have food odor and taste transfer throughout the refrigerator and could also dry out frozen food. Humidity Controlled Crisper and Glide’N’Serve Humidity Controlled Crisper * Depending on the model, some of the following functions may not be available.
HOW TO USE 40 To Remove the Glass Glide’N’Serve and Humidity Controlled Crisper Lift up the glass under the crisper cover, and pull up and out. (Glide’N’Serve not shown for clarity.) To remove the Humidity Controlled Crisper and and the Glide’N’Serve, pull out the Crisper Glide’N’Serve to full extension, lift the front up, and pull straight out. Door Bins The door bins are removable for easy cleaning and adjustment.
41 HOW TO USE ENGLISH Adjusting the Refrigerator Shelves Assembling the Split Shelf (Half Shelf Type) The shelves in your refrigerator are adjustable to meet your individual storage needs. Your model may have full or split shelves. Tilt the front of the shelf up and guide the shelf hooks into the slots at a desired height. Then, lower the front of the shelf so that the hooks drop into the slots. want easier.
MAINTENANCE 42 ENGLISH MAINTENANCE Cleaning . . Both the refrigerator and freezer sections defrost automatically; however, clean both sections about once a month to prevent odors. Wipe up spills immediately. Always unplug the refrigerator before cleaning. General Cleaning Tips . . . . Unplug refrigerator or disconnect the power. Remove all removable parts, such as shelves, crispers, etc. Use a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners.
43 SMART DIAGNOSIS ENGLISH SMART DIAGNOSIS TM (Some models). Should you experience any problems with your refrigerator, it has the capability of transmitting data via your telephone to the LG service center. This allows you to speak directly to our trained specialists. The specialist records the data transmitted from your machine and uses it to analyze the issue, providing a fast and effective diagnosis.
TROUBLESHOOTING 44 Review the Troubleshooting section before calling for service; doing so will save you both time and money. Problem Refrigerator and Freezer section are not cooling. Cooling System runs too much. Possible Causes Solutions The refrigerator control is set to OFF (some models). Turn the control ON. Refer to the Setting the Controls section for proper temperature settings. The refrigerator is in the defrost cycle.
45 TROUBLESHOOTING Problem ENGLISH Refrigerator or Freezer section is too warm. Possible Causes Solutions The refrigerator was recently installed. It may take up to 24 hours for each compartment to reach the desired temperature. The air vents are blocked. Rearrange items to allow air to flow throughout the compartment. Refer to the airflow diagram in the Using Your Refrigerator section. The doors are opened often or for long periods of time.
TROUBLESHOOTING 46 Problem Food is freezing in the refrigerator compartment. Frost or ice crystals form on frozen food (outside of package). Solutions The doors are opened often or for long periods of time. When the doors are opened often or for long periods of time, warm, humid air enters the compartment. This raises the temperature and moisture level within the compartment. To lessen the effect, reduce the frequency and duration of door openings. The doors are not closed correctly.
47 TROUBLESHOOTING Problem Possible Causes Solutions ENGLISH Refrigerator or Freezer section is too cold. Incorrect temperature control settings. If the temperature is too cold, adjust the control one increment at a time and wait for the temperature to stabilize. Refer to the Setting the Controls section for more information. Frost or ice crystals on frozen food (inside of sealed package). Condensation from food with a high water content has frozen inside of the food package.
TROUBLESHOOTING 48 Problem Possible Causes If the doors of the unit are opened often, ambient air will warm the refrigerator which will prevent the unit from maintaining the set temperature. Lowering the refrigerator temperature can help, as well as not opening the doors as frequently. The doors are not closed completely. If the doors are not properly closed, ice cted.
49 TROUBLESHOOTING Problem Possible Causes ENGLISH Ice has a bad The water supply contains taste or odor. minerals such as sulfur. (Ice maker installed only) Solutions A water lter may need to be installed to eliminate taste and odor problems. NOTE: In some cases, a er may not help. It may not be possible to remove all minerals / odor / taste in all water supplies. The icemaker was recently installed. Discard the t few batches of ice to avoid discolored or bad tasting ice.
TROUBLESHOOTING 50 Problem Solutions Rattling noises may come from the flow of refrigerant, the water line on the back of the unit, or items stored on top of or around the refrigerator. Normal Operation The refrigerator is not resting solidly on the floor. The floor is weak or uneven or the leveling legs need to be adjusted. See the “Door Alignment” section. The refrigerator with a linear compressor was jarred while running.