DISHWASHER OWNER'S MANUAL MODEL : LD-9230(1)W(S,M)H LD-9230(1)W(S,M)HB LD-9240(1)W(S,M)H LD-9240(1)W(S,M)HB LD-9250(1)W(M)HB Please read this manual carefully before operating your dishwasher. Retain it for future reference.
CONTENTS SAFETY AND CAUTION 3 INSTALLATION INSTRUCTIONS 5 PARTS NAME 9 FUNCTION OF CONTROL BUTTON 10 HOW TO USE AND OPERATE 14 OPERATING SEQUENCE 20 PROGRAM 21 USER MAINTENANCE INSTRUCTIONS 22 TROUBLE SHOOTING GUIDE 23 SPECIFICATION
SAFETY AND CAUTION IMPORTANT SAFETY INSTRUCTIONS WARNING - When using your dishwasher, follow basic precautions, including the following: enclosure panels are properly in place. open the door very carefully if the dishwasher is operating, there is a risk of water squirting out. • Do not place any heavy objects of stand on the door when it is open.The appliance could tip forward.
SAFETY AND CAUTION CAUTION concerning the Power Cord • Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. • Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous.
INSTALLING INSTRUCTIONS Step 2 : PREPARATION FOR ELECTICAL WIRING WARNING A qualified electrician/plumber or competent person should carry out any electrical/plumbing work required to install this appliance. CAUTION For personal safety, remove house fuse or open circuit breaker before installation. Do not use an extension cord or adapter plug with this appliance. Electrical and earthing connections must comply with the national electrical code/provincial and municipal code and/or other local codes.
INSTALLATION INSTRUCTIONS Step 3 : PREPARING THE DISHWASHER FOR INSTALLATION Step 4 : INSTALLING THE DISHWASHER IN CUPBOARD 1 Lay the dishwasher on its back. 1 Before sliding the dishwasher into the cupboard opening, all necessary height and balancing adjustments should be made using a spanner. 2 Adjust the legs to the required height as shown in below figure. 2 Slide the dishwasher into the cabinet opening carefully. Make sure that the drain hose inside the cabinet is not kinked or stretched.
INSTALLATION INSTRUCTIONS Step 5 : DRAIN LINE CONNECTION 1 If the end of drain hose does not fit to the drain line, use a rubber connector(not supplied) that is resistant to heat and detergent. This should be available from a plumbing shop or DIY merchants. ■ When the drain hose is connected to a separate standpipe, it is essential that an airtight connection be made. Refer to Fig.B 2 There are two typical connections as shown in Figure A, B.
INSTALLATION INSTRUCTIONS Step 6 : WATER SUPPLY CONNECTION Step 8 : HOW TO LEVEL THE DISHWASHER 1 Connect the water supply hose to the water tap as shown.(Some models consist of an inlet valve and hose.) This dishwasher may be fed with either hot or cold water. If the water can not be maintained below 65ºC, the dishwasher must be connected to cold water. After installing the dishwasher, you may notice a slight sticking of the door to the dishwasher, when you open or close the door.
PARTS NAME 4 3 1 2 5 6 7 8 1. Control Panel 2. Front Cover 3. Process Monitor 4. Power Switch 5. Drain Hose 6. Inlet Hose 7. Power Cord 8. Adjust Leg 9. Door Handle 10. Lower Cover Inlet hose(1EA) ※ The appearance and specifications may vary without notice. 9 Funnel(1EA) 11. Upper Rack 12. Cutlery Basket 13. Detergent And Rinse Aid Dispenser 14. Upper Spray Arm 15. Lower Spray Arm 16. Filter ASM 17. Lower Rack 18.
FUNCTION OF CONTROL BUTTON LD-923~ / 924~ Series LD-923~ Series 10 LD-924~ Series
INDICATOR • Refill with special salt • Refill with rinse aid TIME LEFT DELAY START • Before starting, the display window shows the running time of the selected program. • After starting, the display window shows the remaining time. • If the dishwasher has a trouble, the trouble type is displayed. • If you want to delay the start of selected program, press this button before pressing program button. • Pressing the ( ) Button will increase time by 1 hour.
FUNCTION OF CONTROL BUTTON LD-925~ Series PROGRAM CHILD LOCK BEEP ON/OFF • When you want to select program, press each button. • Used to lock or unlock the control buttons to prevent all the setting from being changed by a child. • This function is automatically canceled when power failure occur. • For locking/ unlocking, press Eco and Quick button for a few seconds simultaneously. • The dishwasher must be switched on.
INDICATOR • Refill with special salt • Refill with rinse aid TIME LEFT DELAY START • Before starting, the display window shows the running time of the selected program. • After starting, the display window shows the remaining time. • If the dishwasher has a trouble, the trouble type is displayed. • If you want to delay the start of selected program, press this button before pressing program button. • Pressing the Delay Start will increase time by 1 hour.
HOW TO USE AND OPERATE 1. Loading your Dishwasher Take care not to obstruct the rotation of the spray arms and ensure that large items do not prevent the detergent dispenser lid from opening. For better washing performance, always load the dishwasher according to the instructions. Before loading items into the dishwasher clean off large particles of food, in particular insoluble items such as bones, pips, etc. 3.
HOW TO USE AND OPERATE 4. Loading the Upper Rack 5. Adjusting the Upper Rack (Not on all models) It is best to load this with more delicate items such as, small plates, long cutlery, cups, glasses and dishwasher safe plastic items. Plates should be positioned upwards with the plate bottom facing the front of the rack. Cups, glasses and bowls must be positioned upside down. Extra cups or cooking utensils can be laid on the fold down cup racks, which also provides support for long stem glasses.
HOW TO USE AND OPERATE 6. Adding Detergent Dispenser Push latch to open • Detergent must be put into the detergent chamber before starting every program except the Pre-Wash. • Please follow the manufacturer’s instructions within the manual, when determining the correct amount of detergent to use. • If your dishes are moderately dirty, you may use slightly less detergent than recommended. • Chambers hold 15g and 25g. • The amount of detergent required depends on the program.
HOW TO USE AND OPERATE 7. Adding Rinse Aid Dispenser � For filling To fill the Rinse Aid chamber, rotate the round cap counter clockwise and remove. Fill the container to the maximum level with a good quality Rinse Aid, then replace and lock the cap. The Rinse Aid is automatically dispensed during the final rinse cycle. The dosage is factory set to suit most installations. If, after washing, you notice cloudy spots, streaks or water marks on your glassware, it may be necessary to increase the setting.
HOW TO USE AND OPERATE 8. Salt Filling This model has a water softener to soften hard water. Please read these notes carefully for correct operation. In order to provide satisfactory rinsing results, the dishwasher requires soft water, i.e.,containing little or no lime, otherwise water stains will be left behind on the dishes and interior containers. If the tap water exceeds a certain level of hardness, it must be softened, i.e.,decalcified.
HOW TO USE AND OPERATE ■ For refilling When the salt container is empty, the salt refill lamp will automatically turn on during operation. The salt should be refilled after the cycle has finished. We recommended the salt refill should always be carried out, as mentioned previous page, prior to starting the next operation. This will immediately thin and drain away any excess salt solution. LD-923~ / 924~ Series Note • After filling with salt, it may take a little while before the indicator light turns off.
OPERATING SEQUENCE Press the “Power” button Before starting, the display window shows the running time of the selected program. After starting, the display window shows the remaining time. The time in the display window will start to decrease minute by minute. If the door is opened during the program a safety device ensures that the machine stops. Once the door is re-closed the program will start from where it was interrupted.
PROGRAM ▶Running time may vary according to the water temperature, water pressure and voltage. Program WASH Pre Wash Main Wash RINSE Rinse 1 Rinse 2 Heating Rinse ℃ 50℃ ℃ 70℃ ℃ 70℃ ℃ 45℃ ℃ 65℃ ℃ 70℃ ℃ 45℃ ℃ 65℃ ℃ 40℃ ℃ 65℃ DRY Intensive Normal Eco Quick Pre-wash Intensive Wash Eco Wash This program offers the most efficient energy and water consumption for a good washing performance. It is recommended that it will be used every time.
USER MAINTENANCE INSTRUCTIONS To prevent trouble and poor operating, it is important to check filters and spray arms at regular intervals. Filters Lower Spray Arm • Remove the lower rack first. • Remove the filter by pulling up. • Take out the mesh filter, upper STS filter and outer filter. • Clean them if necessary. • Replace them in the reverse order. • Check that the water jet holes are not blocked. • If cleaning is required, remove the arm by pulling up.
TROUBLE SHOOTING GUIDE ■ If a problem occurs check below to see whether this can be solved. ■ In the unlikely event that the problem cannot be rectified, please contact a service engineer. Possible Causes Problem No lights come on when the power is turned on. • Plug is not properly inserted into the socket. • Fuse blown or circuit breaker tripped. • The electricity of the house was cut off. The machine does not start. • Door is not fully closed. • The start button is not pressed.
LD-9230(1)W(S,M)H LD-9240(1)W(S,M)H LD-9250(1)W(M)HB 450mm 450mm 580mm 530mm 850mm 817mm LD-9230(1)W(S,M)HB LD-9240(1)W(S,M)HB 450mm 550mm Capacity 9 Place settings Weight See rating label Power Supply See rating label Power Consumption See rating label Water Feed Pressure 50 ~ 800 kPa 817mm P/No.