900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. OPERATION DESCRIPTION ( MODEL : GT- 8310C ) SK : TCTU0001701-MG Iss. DATE ’00. 07. 24 1 DESCRIPTION : OPERATION DESCRIPTION OF GT-8310C SHEETS NOTICE NO. DESIGNER CHECKER 28 K961/26/8902 Y. H. Ji J. H.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. This equipment has tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the installation.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. GETTING TO KNOW YOUR NEW PHONE Your new GT-8310C telephone gives you the ultimate in cordless telephone sound quality with the luxury of Caller ID and Call Waiting ID If this is your first cordless telephone, you'11 soon discover that your cordless is similar to regular telephone, except without the cord.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. LOCATING KEYS, LIGHT, AND S WITCHES ON THE B ASE Ne w • Tim Alar •• •/ • Play / St • Volume • Recor d O u •• Rin Progra Eras Pa ger ① The PAGE key - is a homing system for finding the handset. If you press the PAGE key once, the handset beeps for 15seconds. ② IN USE light - becomes lit when the GT-8310C is being used. ③ CHARGE light - comes on solid when the handset is in the base.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. ON THE HANDSET Keys TALK key-Turns the phone on or off so you can dial or talk. Voice mail key. Directly access your V.Mail service 12 : 22 PM 12 / 01 CALL 01 ✉ 1- 555 – 123 - 4567 SMITH JOHN Dialing keys-Control DEL " ! manual dialing.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. HEADSET Jack Allows you to add a headset to the handset (not included, but available by order.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. SETTING UP YOUR PHONE Now that you've checked the contents of the carton, it only takes a few steps to set up your phone. STEP 1. CHOOSE A CENTRAL LOCATION FOR THE BASE UNIT The base should be away from all other electronic equipment such as a personal computer, microwave, stereo ,or television. It is also a good idea to place the unit away from noisy areas, or from heat sources such as a radiator or direct sunlight. STEP 2.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. 4. Turn the mounting bracket around so that the larger part the wedge is set the bottom of the phone. 5. Use the same method to replace the bracket. 6. Insert the 8 inch line cord into phone jack marked TEL LINE. 7. Thread the line cord through the channel on the right-hand side of the bracket to secure the cord. 8. Plug the adapter tip into the adapter jack. Be sure that the tip is all the way into the jack. 9.
00MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. 1. Press down on the battery cover and slide the battery cover down to expose the battery well. 2. Locate the battery connectors inside the battery well. If you are replacing a dead battery, remove the old battery by pulling firmly on the battery cords. 3. Insert the battery plug into the connector. It is polarized and only insert in one direction. 4. Place the battery in the battery well. 5. Replace the battery door. STEP 5.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. To begin the programming sequence, press PGM keys and SETUP PROGRAM appears on the screen. STEP 8. Setting area code Many regions are changing how customers use their area codes. In order to dial from your call records and directory records, the GT8110C needs to distinguish between local and long distance numbers.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. STEP 10. SELECTING YOUR LANGUAGE You can choose between two different languages, English or Spanish. The screen SELECT LANGUAGE appears 1. Press → (REVIEW) key 2. Press ▲ or ▼ key to set SELECT LANGUAGE SELECT LANGUAGE ✓ ENG ESP FRE to ENG or ESP or FRE . STEP 11.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. If you set AUTO ANSWER to ON, GT8110C automatically answer incoming calls when removed from the cradle and If set you also AUTO you could ANSWER to press OFF, press any only key TALK to connect key before after answering incoming incoming STEP 14. SET RING ON or OFF If you don't need to hear the ring sound and select RING ON or OFF . 1. Press → (REVIEW) key RING ✓ ON OFF 3. Press ▲ or ▼ key to set RING to ON or OFF.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. USING YOUR PHONE You can make calls many different ways with the GT-8310C. DIALING (HAND SET) 1. Press TALK key on the handset. 2. Use the number pad to dial the phone number. The phone number appears on the display as you enter the number. You also hear beeps for each digit as you dial. 3. Listen for a connection. 4. Press TALK to end your call. REDIALING Redial is a really fast method of calling your last number.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. FINDING CLEAR RECEPTION Your GT8320C automatically selects 1 of 20 channels at the beginning of the call for the best reception. REACHING MAXIMUM RANGE The GT8310C handset and base communicate up to a certain maximum range. Weather, power lines, or other cordless telephones can affect this distance. The GT8310C beeps whenever you are on the phone and the handset moves out of range from the base.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. b. Press PGM key to enter the speed dialing list again. c. Or, Use the ← or → (REVIEW) keys to find the digit and press DEL key and re-enter the telephone number and the name. NUMBER STORED 6. Press MEMO key to store the complete record. The phone gives you a confirmation tone to let you know that the record is stored. CALLER ID METHOD A quick way to add to your speed dial list is to copy a Caller ID Call Record.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. Press the ▲ or ▼ key on the handset while the phone is not in-use. the phone is not in-use. You hear the sound of the ringer as you adjust the volume between the two levels. ADJUSTING BASESET RINGER VOLUME Press the ▲ or ▼ key on the baseset You hear the sound of the ringer as you adjust the volume USER SLECTABLE RINGER TONES(H/S) There are four user-selectable ringer tones available for this handset. 1.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. THE INTEGRATED ANSWERING DEVICE TURING THE ANSWERING SYSTEM ON/OFF 1. To turn the answering system on, Press OUT DOOR. A tone sounds. Then, the OUT DOOR button is lighted. 2. To turn the answering system off, Press OUT DOOR again, Then, light turns off. SETTING THE CLOCK To set the correct time: 1. Press PROGRAM button. 2. Press TIME button 1. Press |•• or ••| key until you input the correct day.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. Preset Message The following message is pre-recorded “Hello, I cannot receive your call, Please leave your message after a beep. Thank you.” Recording your personal Outgoing Message(OGM) 1. Press RECORD key in stand-by mode. The answering system announces explanation and LED counts recording time. Record your message. (MAX 20 sec) 3. When you finish recording your message, Press •/•(play/stop) button. A tone sounds.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. 2. After reviewing our new messages, you can review your old messages. Press •/•(play/stop) and |•• or ••| to review old messages. SKIPPING A MESSAGE 1. Press •/•(play/stop) to review your messages. 2. Press ••| at anytime to skip to the next message. 3. Press •/•(play/stop) at any time to stop reviewing your messages and return to stand-by mode. DELETING MESSAGES 1. Press •/•(play/stop) to review your messages. 2.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. USING CALLER ID AND CALL WAITING ID One of the best features of your phone is Caller ID, which allows you to see information about an incoming call before you pick up the phone. With Caller ID service from your local telephone company, the GT-8310C telephone displays and records information about the call in a log. Possibly even better than Caller ID is Call Waiting ID.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. REVIEWING CALL RECORDS To review a call Record: 1. Press ← or → (REVIEW) to see how many new calls you have. ← or → (REVIEW) key to move though the Call Record list. 2. Use → (REVIEW) key to see the most recent call record. ☛ Press ← (REVIEW) key to see earlier calls. ☛ Press When you reach either end of the Call Record list, you see an 'END OF LIST' message.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. To delete all Call Records: 1. Press ← or → (REVIEW) key. The display shows you how many call records you have. 2. DEL Press key and ALL : 23 NEW : 03 the GT-8310C asks if you want to delete all Call Records. 3. DEL Press key again and the GT-8310C clears all Call Records, gives you a DELETEconfirmation A LL ? beep.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. VOICE MAIL Voice Mail Service your calls when you are away from your phone or even while you are on the phone. The indicator Light flashes whenever you have message in your mailbox. And once you have programmed your Voice Mail key with your personal access codes, you can get your message at the touch of a button. You must subscribe to Voice Mail Service in order for this feature on your phone. To Program the Voice Mail Key.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. READING DISPLAY MESSAGES The GT-8310C informs you of status by displaying the following messages : Message Display ALL CALLS & NEW CALLS: This message lets you know how many call records you have, and how many of those call records are new, In this example, you have 23 call records, and 3 new calls. ALL : 23 NEW : 03 CHARGING: The handset BATTERY is getting low. Place the handset in the base in order to recharge.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. Message Display NUMBER ONLY: Either name service is not available in your area, or you are subscribing to a number-only service. PRIVATE: The caller has purposely chosen to block his/her phone number. TALK: 10 : 35 PM 10 / 25 CALL 25 555–5555 10 : 35 PM 10 / 25 CALL 25 PRIVATE TALK The handset is on and ready for you to dial. PAGING : PAGING The Base is calling the handset.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. Message Display OUT OF RANGE: If you use the handset too far away from the base unit during a call, the handset will alert you OUTbyOF audio RANGE warning (when using talk) and OUT OF RANGE appears on the display. NUMBER STORED : When you save the call records in the directory or create a speed dialing list, you will see the display like this. Forwarded CALLS : The message sent is a forwarded calls.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. TROUBLESHOOTING Are you having trouble with your phone? Here are some of the most common problem areas and solutions. SYMPTOM CORRECTIVE ACTION No dial tone ☛ Verify that the line cord is connected and secure. ☛ Check to see that you are not out of range to the base. ☛ Check that the AC adapter is plugged into the outlet. ☛ Check that the handset is fully charged.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM. SYMPTOM CORRECTIVE ACTION NO DATA ☛ Check your service. Call your local phone company to ensure that you have Caller ID or Call Waiting ID service. ☛ Check the answering machine. Ensure that your answering machine is set to answer after two rings. ☛ You answered the call before two rings. ☛ Check call Forwarding. Ensure that Call Forwarding is turned off.