32LY570H 39LY570H 42LY570H 47LY570H 55LY570H Lodging Guest Interactive Pro:Centric ® TVs Commercial Mode Setup Guide Note: Selected features shown in this guide may not be available on all models. EXPERIENCED INSTALLER EZ-Manager Wizard pages 12 – 18 Custom Master TV Setup pages 32 – 34 Cloning Procedures pages 35 – 38 © Copyright 2014 LG Electronics U.S.A., Inc.
For Customer Support/Service, please call: 1-888-865-3026 The latest product information and documentation is available online at: www.LGsolutions.com MODEL and SERIAL NUMBER The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here: Model No._________________ Serial No._______________ WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK).
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 22. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power lines or circuits as death or serious injury can occur.
Table of Contents Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 3 – 4 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Commercial Mode Overview . . . . . . . . . . . . . . . . . . . . 6 – 9 Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Pass-through Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Commercial Mode Overview This document describes how to set up LY570H Pro:Centric® TVs for Commercial Mode operation. LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’s CPU, Protocol Translator Card (PTC), or the embedded b-LAN™ (EBL) module, or it resides externally from the TV (i.e., in a device from the solution provider). These TV models are capable of Free-To-Guest (FTG) Mode operation via the TV CPU.
Commercial Mode Overview (Cont.) Installer Menu To create a Master TV Setup, you will need to know how to access the commercial controller (PTC) Installer Menu and make changes to the default values as required. If necessary, familiarize yourself with the Installer Menu and how to make and save changes. Refer to pages 22 to 31 for information on accessing the Installer Menu and for detailed descriptions of the Installer Menu items.
Commercial Mode Overview (Cont.) FTG Mode In this mode, an FTG Channel Map enables the decryption of each Pro:Idiom® Encrypted channel. The FTG Channel Map also provides logical channel mapping of physical RF channels (analog and digital) and Aux inputs. The method for creating the FTG Channel Map is ultimately determined by which element of the TV will “own” the FTG Channel Map—the CPU or the EBL.
Commercial Mode Overview (Cont.) While the TV is in FTG Mode: • Users can still access the Installer Menu using an LG Installer Remote; however, all Installer Menu items will be read-only. • FTG Mode via CPU configuration changes must be made using a TLX file (typically edited in the FTG File Manager), while FTG Mode via EBL configuration changes must be made using the the FTG Device Configuration Application.
Pro:Centric Operation Pro:Centric Interactive Menu Features LG’s Pro:Centric application enables guests to locate and select television entertainment using an interactive channel guide, check the daily weather, and view hotel and surrounding amenities via custom billboards and points-of-interest maps. Pro:Centric application features include: • Portal and information screens/pages (including a “Welcome” page) that include branding logos. • An optional customized user interface (custom “skins”).
Pro:Centric Operation (Cont.) Pro:Centric Setup Administration and management options for the Pro:Centric server are described in detail in the Pro:Centric Server Admin Client User Guide. This document describes only those settings that must be specified on the TVs to enable Pro:Centric remote management and/or the Pro:Centric application.
EZ-Manager Wizard The primary purpose of the EZ-Manager Wizard is to guide you through the process (automated or manual) of configuring the essential Installer Menu items for Pro:Centric operation. The wizard will appear on the screen each time the TV is turned ON, until one of its configuration methods has been completed or the wizard is exited. Use the Installer Remote to make selections and complete each wizard step.
EZ-Manager Wizard (Cont.) From the Welcome screen, you have the following options: • To proceed with the EZ-Manager Wizard, use the arrow keys on the Installer Remote to select/ highlight Next and press OK. Then, continue to the “TV Configuration Options” section below. • To exit the wizard, but retain the use of the Pro:Centric remote management feature on this TV (i.e.
EZ-Manager Wizard (Cont.) Zone and Room Number Assignments You may complete one or more of the fields in the Zone, Label, and Room Number screen or leave them at their default settings (Zone) or blank (Label and Room Number), as desired; however, if you intend to use the Zoning feature on this TV, you MUST specify the appropriate value in the Zone field as described below. See also Reference section, “Using the TV Zoning Feature,” for further information.
EZ-Manager Wizard (Cont.) Configure Pro:Centric Settings Once you select “Next” from the TV Configuration Options screen, the Searching for Pro:Centric Server screen is displayed (see example at right), and you have the following options: Z EZ-Manager Wizard 1 2 3 4 Searching for Pro:Centric Server...
EZ-Manager Wizard (Cont.) Manual Pro:Centric Configuration 1. With the Searching for Pro:Centric Server screen on display, use the arrow keys on the Installer Remote to select/highlight the Manual Pro:Centric option at the bottom right of the screen, and press OK. Z EZ-Manager Wizard 1 2 3 4 Searching for Pro:Centric Server... It may take 1 min 32 second(s). This step automatically searches for the Pro:Centric server.
EZ-Manager Wizard (Cont.) (Continued from previous page) 4. Once all fields are completed as required, you have two options (see also note below): EZ-Manager Wizard 1 2 3 4 Pro:Centric Manual Configuration • To save the data entered and exit the wizard, use the arrow keys to select Exit and then press OK. In the subsequent pop-up confirmation window, select Save and Exit, and then press OK once more.
EZ-Manager Wizard (Cont.) Before You Begin • If you intend to use the Zoning feature on this TV, make sure to assign the appropriate TV Zone # in the EZ-Manager’s Zone, Label, and Room Number screen BEFORE continuing with USB Configuration. See “TV Configuration Options” on page 13 for further information. • Ensure the USB device to be used has been formatted with FAT format. • Refer to “Ez Download Utility” on pages 19 to 21 for further information on the Ez Download utility.
Ez Download Utility The Ez Download utilty, available from the TV Manager / USB Download Menu, enables you to select multiple files at one time from the files loaded on a USB memory device. You may use this utility to download any one or all of the following to a TV: a TLX file for configuration purposes, a TV CPU or PTC software update, a splash screen image.
Ez Download Utility (Cont.) (Continued from previous page) 4. To access the TV Manager / USB Download Menu from the TV menus: • Press MENU SETTINGS on the Installer Remote to display the TV setup menus (TV is in Pass-through Mode) or the Function Menu (TV is not in Pass-through Mode). • Use the arrow navigation keys to select/highlight either the Option menu icon from the TV setup menus or the Lock menu icon from the Function Menu. Then, press the number “7” key a total of seven times. 5.
Ez Download Utility (Cont.) (Continued from previous page) Note: Press on the Installer Remote, as necessary, to exit the Ez Download screen and/ or the TV Manager / USB Download Menu. If you accessed the TV Manager / USB Download Menu via the EZ-Manager Wizard, you will be returned to the last screen on display before you selected the “USB Configuration” option. If you accessed the TV Manager / USB Download Menu via the TV menus, you will be returned to TV viewing. 8.
Installer Menu Use the Installer Menu to set up, change, or view operational settings. This section describes how to access, use, and exit the Installer Menu from the TV itself. However, you should also refer to the Installer Menu descriptions in this document if you are configuring the TV CPU using a TLX file created using LG’s FTG File Manager software or configuring the EBL locally (.rml) or remotely (via FMA-LG101 / .fma) using the FTG Device Configuration Application software.
Installer Menu (Cont.) As part of the Installer Menu header (in all modes), two 3-character acronyms are displayed to indicate the TV’s current configuration mode. The table below lists all possible mode identifiers for these TV models.
Installer Menu (Cont.) Installer Menu Items 000 through 073 Item Function 000 001 002 003 004 STRT CHANNEL 005 CHAN LOCK 24 Value Range Default Value INSTALLER SEQ 0~3 0 Leave default set to 0. POWER MANAGE 0~7 0 Sets number of hours of no activity before automatic shutoff. AC ON 0/1 0 Set to 1 to enable TV to turn ON when AC power is applied. BAND/AFC 0~3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC 0 ~ 127, 255 255 Channel tuned when TV is turned ON.
Installer Menu (Cont.) Installer Menu Items 075 through 122 Item Function Value Range Default Value Brief Description of Function 075 REVERT CH 078 UPN MSB 0/1 0 If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel. 0 ~ 255 0 User programmable number, most significant byte. 079 UPN MSB-1 080 UPN MSB-2 0 ~ 255 0 User programmable number, most significant byte - 1. 0 ~ 255 0 User programmable number, most significant byte - 2.
Installer Menu (Cont.) Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The Power Management function is for saving energy. If set to 0, Power Management is Off.
Installer Menu (Cont.) 015 - SLEEP TIMER If set to 1, the Sleep Timer feature may be used. If set to 0, the Sleep Timer is not available. 016 - EN. TIMER (Enable On/Off Timers) If set to 1, the Timer function is available to the end user and enabled continuously. Set to 0 to disable On/Off timers. Note: The TV clock must be set in order for timers to be used. 017 - ALARM Gives the installer the option of making the Alarm function available to the end user.
Installer Menu (Cont.) • IR Decode: Set to 0 (default) to allow the TV to process all IR 069 - EN. CH-T COL. (Enable Channel-Time Custom Color) Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display. • Device ID: Set to 0 (default) to allow the TV to communicate 070 - FOR.
Installer Menu (Cont.) 083 - HANDSHK TIME (Handshake Time) Adds an additional delay to the handshake time which is 64 msec, thus relaxing MPI timing requirements to be compatible with PCbased Windows controlled systems. Range is 0 - 5. (Timeout = 25.5MS + [25.5 MS* Handshake time].) 084 - PERMANENT BLK (Permanent Block) Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function. Set to 1 to install Parental Control restrictions permanently.
Installer Menu (Cont.) 098 - PRO:CENTRIC Selects the Pro:Centric Application Mode. Set to 0 (default) to disable the Pro:Centric application. Set to 1 for Flash Mode. Set to 2 for GEM (Java Application) Mode. In order to retrieve the Pro:Centric application, when enabled (for Flash or GEM Mode), the TV must be turned OFF/ON two times. Once you exit the Installer Menu, turn OFF the TV for at least one minute.
Installer Menu (Cont.) 119 - DATA CHANNEL Set to 0 to disable. Set from 1 to 135 to match the RF channel number that will be used by the Pro:Centric server as its data channel. * 121 - UPDATE TIME HR Set the Wake For Update hour from 0 to 23. This item uses the 24-hour clock format. The value “128” is displayed as “OFF.” Directly entering 128 turns the Wake For Update feature OFF.
Custom Master TV Setup This section describes how to create a customized Master TV Setup for cloning purposes when the TV is in Pass-through Mode. The Master TV Setup can used to configure either TVs that are to remain in Pass-through Mode or TVs that are to be configured for FTG Mode via CPU. Note: Cloning requirements and procedures are described in detail on pages 35 to 38. Note: You can use the FTG File Manager to create an FTG Configuration (.
Custom Master TV Setup (Cont.) Custom Master TV Setup Procedure 1. Turn ON the TV. If the EZ-Manager Wizard appears on the screen when you turn ON the TV, use the arrow keys on the Installer Remote to select Exit from the Welcome screen and press OK. In the confirmation pop-up window, select OK, and then press OK once more on the Installer Remote to exit the wizard. 2. Set Installer Menu items. This step provides specific instruction only on the Installer Menu items that should be set on a Master TV.
Custom Master TV Setup (Cont.) (Continued from previous page) 3. Set up TV features. On-screen setup menus control the features of the TV. Press MENU SETTINGS on the Installer Remote to access the TV setup menus, and then set Channel, Picture, Audio, Time, etc. options to the desired configurations. See “Clonable TV Setup Menu Features” list on previous page and also notes below.
Cloning Procedures Cloning typically refers to the process of capturing a Master TV Setup and transferring it to a Target TV. This section describes how to save (Learn) a Master TV Setup and transfer (Teach) it to a Target TV using a USB memory device / TLX file. You can also create a TLX file using the FTG File Manager and then use the Teaching procedure to transfer the TLX file to Target TVs. Refer to “Creating an FTG Configuration File” on pages 39 to 40, as necessary.
Cloning Procedures (Cont.) (Continued from previous page) 7. In the Learn From TV (TLX) window, to differentiate this TLX file from others, you can use the Up/Down arrow keys to change the last five digits of the filename. Press OK when you are ready to initiate Learning. Learning status will be shown on a progress bar in a new window. Do NOT remove the USB device until Learning is complete. When the Learning process is complete, the TV Manager / USB Download menu will reappear on the screen. 8.
Cloning Procedures (Cont.) (Continued from previous page) • If the TLX file contains an FTG Channel Map that was created in the FTG File Manager, all physical RF channels and Aux inpupts have been assigned logical channel numbers. When you Teach the FTG Channel Map to the Target TV(s), you will have the option to select logical or physical channel tuning. If you select physical channel tuning, the physical RF channels and Aux inputs in the FTG Channel Map will remain in logical order.
Cloning Procedures (Cont.) (Continued from previous page) 5. Use the arrow navigation keys to select/highlight either the Option menu icon from the TV setup menus or the Lock menu icon from the Function Menu. Then, press the number “7” key a total of seven times to display the TV Manager / USB Download Menu. 6. With the TV Manager / USB Download Menu on display, use the Up/ Down arrow keys to select Teach To TV (TLX), and then press OK. TV Manager USB Logo Image Download 7.
FTG File Manager Utilities Overview As indicated in the introduction to this document, there are two separate and distinct methods for configuring LY570H TVs for FTG Mode of operation: one method is to configure the TV CPU for FTG Mode operation, while the other is to configure the TV EBL for FTG Mode operation. FROM A LOCAL CONFIGURATION STANDPOINT, EACH OF THESE METHODS IS MUTUALLY EXCLUSIVE. IF THE CPU IS IN FTG MODE, THE EBL CANNOT BE SWITCHED TO FTG MODE.
FTG File Manager Utilities Overview (Cont.) (Continued from previous page) Note: To remove an individual item from the FTG Configuration List or the TV Setup Menu List, click on/ highlight the item to be removed, and then click the Remove Item button directly above the applicable “List” window. To clear both the current FTG Configuration List and TV Setup Menu List contents, click the Clear button in the List command section of the FTG File Manager main screen.
FTG File Manager Utilities Overview (Cont.) FTG File Manager Main Screen The FTG File Manager main screen enables you to compile, modify, and save FTG Configuration (.tlx) files. It also allows you to change the Zone assignment for each Installer Menu profile, if desired (see Reference section, “Using the TV Zoning Feature,” for further information). FTG CONFIGURATION LIST Data to be saved in FTG Configuration (.tlx) file. CLEAR/SAVE FTG Configuration and TV Setup Menu List options.
FTG File Manager Utilities Overview (Cont.) FTG Channel Map Configuration Utility The FTG Channel Map Configuration Utility enables you to create, view, edit, and print a Logical Channel Map. EDIT/ADD MAP Click to open the FTG Channel Map Editor to create or edit an FTG Channel Map (see next page). PRINT MAP Click to display a printable FTG Channel Map Report. The report can also be exported as an HTML or Text file. Filename of opened FTG Configuration (.
FTG File Manager Utilities Overview (Cont.) FTG Channel Map Editor The FTG Channel Map Editor shows a single Logical Channel’s data and the FTG Channel Map. LOGICAL CHANNEL MAPPING Select a Logical Channel number. Then, assign the RF, Major, and Minor channel numbers to complete the mapping. CUSTOM CHANNEL LABELS/ICONS Enter custom labels and select icons by name on menu or by number. SET CHANNEL ATTRIBUTES Check/select Encrypted, OSD, or Blank Video.
FTG File Manager Utilities Overview (Cont.) FTG Installer Menu Configuration Utility CONFIGURATION SETTINGS Select tabs for categories of Installer Menu items to set up TV. Filename of opened FTG Configuration (.rml) file created using FTG Device Configuration Application. Notes: • The Pro:Centric tab enables you to set up Pro:Centric-specific parameters. Refer to the Free-ToGuest (FTG) File Manager User Guide for further information. • LAN and Hospital parameters are not applicable for these TV models.
IP Environment Setup IP Environment Move OK Move OK The IP Environment Menu enables you to set up the network features of the TV. With the exception of Network Connection settings, the IP Environment settings are editable (with the Installer Remote) only if the TV is in Pass-through Mode and read-only when the TV is not in Pass-through Mode.
IP Environment Setup (Cont.) (Continued from previous page) The next Network Setting window will enable you to specify the IP and DNS configuration for this TV. Auto settings will be selected by default. Use the arrow keys to select the appropriate options, and specify the configuration data for the IP and DNS modes. When all fields are completed, select OK on the screen and press OK on the Installer Remote. Network Setting Select the IP setting mode.
IP Environment Setup (Cont.) IP Environment Move OK IP Environment Move OK Pro:Centric Setup Pro:Centric options enable you to configure the TV with the appropriate settings to connect to the Pro:Centric server. Use the Up/Down arrow keys on the Installer Remote to navigate between fields. 1. With the IP Environment Menu on display, use the arrow keys on the Installer Remote to select Pro:Centric. Then, press OK.
IP Environment Setup (Cont.) (Continued from previous page) IP Configuration a) In the Media Type field, use the Left/Right arrow keys to select IP. Note: If the Media Type has already been set in the EZ-Manager Wizard, the specified value will be reflected in this field. Note: Setting the Media Type to “IP” automatically sets the Data Channel field to “253.” You cannot alter this setting (unless you revert Media Type to “RF”). Also, it is not possible to direct enter “253” in the Data Channel field.
Reference: Remote Jack Pack / TV Connections & Setup Remote Jack Pack Setup RJP Available? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item 093 RJP AVAILABLE appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP AVAILABLE to 1). See Installer Menu detailed descriptions for further information. 093 RJP AVAILABLE 001 TV Connections Make these connections ONLY after Master TV Setup and TV cloning procedures are complete.
Reference: Upgrading TV/PTC Software using a USB Memory Device This section describes how to update TV (CPU) and/or PTC software using the TV Manager / USB Download Menu “Upgrade TV Software” and/or “Upgrade PTC Software” option(s), respectively, though you may also use the Ez Download utility to upgrade software, if desired. See “Ez Download Utility” on pages 19 to 21 for further information.
Reference: Downloading a Splash Screen using a USB Memory Device This section describes how to download a splash screen image using the TV Manager / USB Download Menu “Logo Image Download” option, though you may also use the Ez Download utility to download the splash image, if desired. See “Ez Download Utility” on pages 19 to 21 for further information. Splash Screen Image File Guidelines • The splash screen image must be a baseline (not progressive) JPEG. • The image should be no larger than 1 MB.
Reference: Power Consumption Settings The following tables assume that Installer Menu item 118 POWER SAVINGS is set to 3 (default) and Installer Menu item 099 BACK LIGHTING is set as shown below (default value is 202).
Reference: TV Aux Input Configuration ENABLE DIRECT ACCESS Tuning * TV MPI DATA MPI DATA STATUS TYPE 0x41 SOURCES ENABLED (R/W) Installer Menu DATA STATUS TYPE 0xD2 CURRENT AV SOURCE (R) DATA STATUS TYPE 0x0D AUX SOURCE (R) Installer Menu Item 029 OLD OCV =0 Installer Menu Item 029 OLD OCV =1 Aux Input Input Mode Item Function Value Enable Bit Label Value Value Description 131 91 Video1 (Rear) CV 39 REAR AUX EN 1 1 Rear Video (Aux) 1 0 VIDEO 132 92 HDMI2 91 HDMI2 ENABLE 2
Reference: b-LAN Setup & Overview The b-LAN module is internal to the TV. It allows hotel/institution head end equipment with b-LAN technology to communicate, via the institution’s RF distribution system, with the TV for configuration and control. Installer Menu item 118 POWER SAVINGS controls the power circuitry for both the embedded b-LAN module and the GAME CONTROL/MPI port. The default value is 3—the b-LAN module is only powered when the TV is turned ON. See chart below.
Reference: FTG Mode via EBL (Local Configuration) The following steps outline local FTG configuration of individual TV EBLs using a direct PC-to-TV connection. Refer to the Free-To-Guest (FTG) Device Configuration Application User Guide for further information. FTG Device Configuration Application software is available online at: www.LGsolutions.com/ftgsoftware. Note: If the TV CPU is already in FTG Mode, you cannot use this procedure to make changes to the FTG Channel Map and FTG Installer Menu settings.
Reference: Auto Input(s) Sensing Feature This section provides detailed settings information for Installer Menu item 042 AUTO INPUTS. To disable auto-sensing for all available Aux inputs, set item 042 to 0. To enable auto-sensing for all available Aux inputs, set item 042 to 255. For specifications on all other available settings (i.e., settings for individual inputs), refer to the table on the following page.
Reference: Auto Input(s) Sensing Feature (Cont.
Reference: RJP Model List & Input Auto-sensing Hierarchy RJP Legacy Models • RJP-101M • RJP-110WBR • RJP-101ML • RJP-110S • RJP-110F • RJP-120G • RJP-110FW • RJP-120T • RJP-110W • RJP-201B/202B RJP Scaler Models • RJP-201M • RJP-301B • RJP-401B RJP Input Auto-sensing Hierarchy 58 Priority Video Audio 1st (Highest) Digital Video In Audio In (3.
Reference: Restoring Factory Defaults on the TV(s) This section describes how to restore factory defaults either on a single TV that is currently in Pass-through or FTG Mode or on multiple TVs that are currently in FTG Mode. Note: If the TV(s) is/are currently in FTG Mode, restoring the factory defaults also resets the TV to Passthrough Mode.
Reference: Using the TV Zoning Feature This section describes the TV Zoning feature available with the LY570H model TVs. The TV Zoning feature enables you to create localized configurations for TVs in selected locations, or “Zones,” within the installation environment, for example, a hotel lobby, fitness center, restaurant, etc. This feature is primarily intended for use when the TV is configured for FTG Mode via CPU operation.
Reference: Using the TV Zoning Feature (Cont.) Note: While a channel can be restricted from up to eight Zones, a TV can only ever be in (set for) one Zone. See also the FTG Channel Map Editor overview on page 43. At the same time, keep in mind that the TV Zone designations are not mutually exclusive.
Reference: Using the TV Zoning Feature (Cont.) (Continued from previous page) To change the TV Zone, navigate to the Zone field, and use the Up/Down arrow keys to specify the desired TV Zone # (0–8). • Label: Allows you to select a North, South, East, or West text label for this TV. Use the Up/Down arrow keys to select the applicable label. • Room Number: Allows you to specify the number of the room in which the TV is located.
Reference: LY570H Rear and Side Jack Panels UPDATE Restricted to software updates. HDMI IN 1 Connection for HDMI output from external device. RESET Initiates a hardware reset and turns the TV OFF. GAME CONTROL/MPI When the TV/EBL is in Pass-through Mode, the MPI function enables an external MPI control device (i.e., VOD/PPV STB, etc.) to control the TV. Game Control—EBL in LodgeNet PPV Mode only. TV-LINK CFG (3.5 mm jack) Use for direct PC-to-TV FTG configuration.
Reference: External Stereo Speaker Setup EXTERNAL SPEAKER_R- (Sleeve) The three-contact (left, right, ground) SPEAKER OUT 3.5 mm jack on the LY570H rear panel provides EXTERNAL SPEAKER_R+ (Ring 2) stereo speaker signal outputs (fixed speaker, variable speaker, or fixed line level [amplifier]) for external EXTERNAL SPEAKER_L- (Ring 1) audio equipment. Set Installer Menu item 097 AUDIO OUTPUT as required in accordance with external audio equipment connectedEXTERNAL to theSPEAKER_L+ TV.
Reference: Installer Remote Control Typical Key Functions The LG Installer Remote is supplied with and dedicated to operate the TV. The LG Installer Remote illustrated below shows typical remote control functions and is provided for reference only. This Installer Remote may vary from the Installer Remote supplied with the TV. Q.MENU (POWER) Turns the TV ON or OFF TV/DVD Select the remote’s operating mode: TV or DVD. INPUT NUMBER Buttons (0 - 9) & DASH Use to enter a channel or program number.
Troubleshooting General Troubleshooting Some Quick and Easy Tips for Resolving Problems Installation Symptom Possible Cause(s) Possible Solution(s) Cannot direct enter channel number. (TV in Pass-through Mode) Installer Menu item 028 CH. OVERIDE is set to 0, i.e., disabled (recommended setting). If Installer Menu item 028 CH. OVERIDE is set to 0, only channels that are active in the TV’s channel lineup can be selected. Set CH. OVERIDE to 1 to allow access for direct keypad entry to all channels.
Troubleshooting (Cont.) Commercial Mode Check / FTG Operation Troubleshooting Commercial Mode Check Use this flowchart to determine whether the TV is currently in Commercial Mode. Press POWER on Installer Remote. TV turned ON? No TV connected to AC Power? No Plug into AC Power outlet. Yes Yes Bad TV Leave the TV set ON, and press MENU SETTINGS on the Installer Remote. Function Menu on display? No Press MENU SETTINGS repeatedly as if to access the Installer Menu.
Glossary of Terms b-LAN LodgeNet Interactive Corporation proprietary RF communication system used to configure/control TV via RF distribution system. Channel Lineup Channels set in the TV memory, via Auto Tuning/manual editing. Cloning The process of capturing a Master TV Setup and transferring it to a Target TV using a USB memory device.
Document Revision History / Open Source Software Notice Document Revision History Date Description April 2014 Revision A: New document Product documentation is available online at: www.LGsolutions.com. Open Source Software Notice To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource.lge.com.
For Customer Support/Service, please call: 1-888-865-3026 www.LGsolutions.com Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric is a registered trademark of LG Electronics Inc. b-LAN is a trademark of LodgeNet Interactive Corporation. All other trademarks or registered trademarks are the property of their respective owners. © Copyright 2014 LG Electronics U.S.A., Inc.
