INSTALLATION 9 INSTALLATION ENGLISH Before Installing Parts not Provided a Water Supply Tube d Air Gap b Fittings for Tube e Hose Clamp c Coupler f 3/4" Elbow g Baseboard (Wood) Tools Needed a Flat-Blade Screwdriver f Safety Glasses k 1/4” Square Drive Wrench b Phillips Screwdriver g Adjustable Wrench (2) l Pliers c Hole Saw min.
10 INSTALLATION Product Dimensions • For flush installations only, you may remove the cabinet brace a inside the cabinet. Front View 23 1/2” (598 mm) 22 1/2” (572 mm) 32 1/16” (815 mm) Choosing the Proper Location 18” (455 mm) 1 Side View Select a location as close to the sink as possible for easy connections to water supply line, drain hose and electrical connection. 45 1/2” (1155 mm) Min . 23 (600 5/8" 32 1 mm ) (82 /4 " - 34 0-8 76 1/2 " mm) " .
INSTALLATION 11 result in kinked, pinched, crushed, stressed or damaged lines. • Condensation may occur on the underside or along the front edge of the countertop when the room temperature is low. WARNING Installing Moisture Barrier Tape Install the moisture barrier tape to the underside of the countertop to protect the surface from condensation when the appliance is opened. 1 Clean and dry the area on the underside of the countertop and the sides of the cabinet opening where the tape will be applied.
12 INSTALLATION CAUTION 6 • Water supply pressure must be between 20 psi and 80 psi (140–550 kPa). If the water supply pressure exceeds 80 psi, a pressure reducing valve must be installed. Otherwise premature failure of the inlet valve may occur. Turn on the water and check for leaks at the connections. • If there is a leak, reconnect the elbow. • Do not cross thread or overtighten the connections to avoid leakage. Connecting Water Supply Line and Power Water supply tube: Minimum 3/8″ O.D.
INSTALLATION 13 Removable Shipping Brace ENGLISH The rear shipping brace can be removed if additional clearance is needed when installing the dishwasher under a low countertop. 2 Removing Packing Materials from the Interior Bend the tabs on the brackets to secure them to the frame using a pair of needle nose pliers. Remove all packing materials from the interior of the dishwasher before installing the appliance.
14 INSTALLATION water supply. As you slide the dishwasher into the opening, slowly pull on the drain hose from inside the cabinet to take up some slack. Be careful not to kink, pinch, crush or stress the drain hose during installation to avoid leaking and water damage. CAUTION • Do not push the top of the dishwasher. Doing so can damage the interior of the dishwasher. NOTE 4 • Open the door and grab the body frame and the top front opening b of the tub to move or lift the dishwasher.
INSTALLATION 15 2 Tighten the connection using a square drive wrench to avoid putting stress on the water tap. • Cut the adapter so the end matches the size of the drain connection. ENGLISH NOTE • For drain hose installation, use the screw style hose clamp provided with this dishwasher in the silverware basket. Connecting Power Insert the power plug into a grounded outlet. • The power cord should not be positioned behind the appliance but within 47.
16 INSTALLATION 2 Remove the knockout plug a from the disposal. 2 WARNING Attach the drain hose to the waste tee with the hose clamp provided. Move the clamp into position and tighten it with a flat-blade screwdriver. • If the knockout plug has not been removed, the dishwasher will not be able to drain properly. Connecting to Disposal or Waste Tee with Air Gap 3 Attach the drain hose to the disposal with the hose clamp provided.
INSTALLATION 17 Leveling Dishwasher Check that the dishwasher is level and adjust the leveling feet if necessary. Make sure that the gap between the tub walls and the door liner is the same on either side. ENGLISH CAUTION • Failure to level the dishwasher may result in leakage, problems closing the door, or noise.
18 INSTALLATION Adjusting Rear Leveling Foot Use a Phillips screwdriver to adjust the rear leveling foot and the rear of the tub using the center screw at the base of the appliance in the front. Securing Dishwasher to Countertop Use the bracket screws provided to secure the brackets at the top of the dishwasher to the underside of the wood countertop. • Turn the center screw clockwise to raise the rear of the tub and counterclockwise to lower it.
INSTALLATION 19 • Make sure that all packaging materials have been removed. ENGLISH 2 Attach a custom toe kick. If needed, use a saw to cut a notch in the top of the custom toe kick to provide clearance for the cabinet panel when opening the door. Final Installation Check Testing the Dishwasher Check if the dishwasher is properly installed. 1 Turn on the circuit breaker. 2 Turn on the house water supply. 3 Make sure that the door opens and closes smoothly.
20 INSTALLATION Error Code IE Possible Cause and Solution Water supply line is kinked under dishwasher. • Feed the drain and water supply hoses through the hole under the sink. Then gradually slide the dishwasher into the cabinet while pulling on the hoses under the sink to take up any slack. This helps avoid kinking the hoses or trapping them beneath the dishwasher. House water supply is not turned on. • Turn the water faucet on.