32LC50C 32LC50CB 32LC50CS 32LX50C 32LX50CS 37LC50DC 37LC50CB 42LB50C 42LC50C Integrated TVs Setup & Operation Guide for Commercial Mode Note: All features shown within this guide may not be available on all models. Experienced Installer Master TV Setup page 6 Cloning Information pages 7-8-9 © Copyright 2008, LG Electronics U.S.A., Inc.
Installer Overview PTC INSTALLER MENU This is the commercial mode setup guide only. For all other information refer to the separately-supplied TV Owner’s Manual (Users guide). Operating Installer Menu To set up the controls for the TV you will need to know how to enter the TV Installer menu and make changes to the default values as required. If necessary, familiarize yourself with the TV Installer menu and how to make and save changes in the menu.
Table of Contents Use this page as a reference to find pages or sections to go to and set up the TV features. Go to page 6 to begin the Commercial Mode Master TV setup. 1. 2. 3. 4. Connect TV to RF signal source. Customize TV features and set up other operational controls in the Installer’s menu. Copy the Master TV setup into the clone programmer. Transfer the Master TV setup from the clone programmer to identical TVs. Installer Overview . . . . . . . . . . Table of Contents . . . . . . . . . .
Typical Installer Multi-Brand Remote Control INPUT TV MODE TV POWER INPUT DVD MULTI VCR PIP CH - PIP CH + PIP INPUT PIP EZ PIC EZ SOUND INFO SWAP LG Multi-brand Remote Control Use the MODE button to select TV and put installer remote into TV operating mode. Notes: This remote is supplied with the TV. This typical LG multi-brand remote control is shown for reference. See next page for typical key functions in TV mode.
Installer Remote Control Typical Key Functions Remote Control Key Functions. To put remote into TV operating mode, select TV with the MODE key. Notes: This remote is supplied with the TV. This typical LG multi-brand remote control is shown for reference. Follow the instructions provided on the next page to access the Installer menus. TV INPUT/INPUT Select available input sources. POWER Turns your TV or any other programmed equipment On or Off, depending on mode.
Commercial Mode Setup for Master TV This page provides an overview of the TV configuration. See the pages listed below for more specific, detailed instructions at each step; how to access and use the Installer menu etc. Note 1: Disconnect all Aux inputs. Under certain conditions, EZ Scan (Channel search) is disabled if there is an Aux input active. PTC INSTALLER MENU Overview: Commercial Mode Setup Procedure 1. Set Installer Menu Items (Enter Installer Menu, see page 10 for detailed instructions.) a.
Cloning Connections/Learning Setup Connections for the LT2002 Clone Programmer to Learn the TV Master TV Setup Antenna or CATV Ferrite Core (TDK, ZCAT 2035-0930) Connect cable to TV MPI Jack and follow on screen instructions Status Indicator MPI Reset Color battery ok battery low • green • red Blink pattern • slow power on no communications • heartbeat power on communications ok THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION CLONE CLOCK = XX:XX TV CLOCK = X
Cloning Learning Setup Learning the Master TV Setup Instructions for the Clone Programmer to Learn the Master TV Setup THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION Use MPI Cable to Connect LT2002 Clone Programmer to Master TV MPI Port If there is a good connection, “THE CLONE HAS CONTROL OF TV” message will appear. Press any key on the Installer remote. CLONE CLOCK= TV CLOCK= XX XX XX XX:XX XX:XX -PRESS ANY KEY TO CONTINUE. -DISCONNECT CLONE WHEN DONE.
Cloning Connections/Teaching Setup Teaching the Master Setup to Another TV Connections for the LT2002 to Teach another TV the Master Setup Antenna or CATV Ferrite Core (TDK, ZCAT 2035-0930) Connect cable to TV MPI Jack and follow on screen instructions Status Indicator MPI Reset Color battery ok battery low • green • red Blink pattern • slow power on no communications • heartbeat power on communications ok THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION XX
Installer Menu Use the Installer’s Menu to set up or change operational settings. See more detailed descriptions of the Installer menu items on the following pages... Accessing the Installer’s Menu Make sure TV is on. Installer’s menu items can be accessed by using an installer’s remote control. Just press MENU repeatedly until the TV seems to stop responding, then press 9, 8, 7, 6, then ENTER to access the Installer’s menu. To remove the Installer’s menu, press ENTER again.
Installer Menu Installer Menu Items 035 through 118 Menu Item Function Value Range Default Value Brief Description of Function and Comments 035 COMPPORT EN. 0/2 1 Set to 0 to disable HDMI 1. Set to 1 for DTV, set to 2 for PC. 038 YPrPb EN. 0/1 1 Set to 1 to enable display panel Component Video input jacks. 039 REAR AUX EN 0/1 1 Set to 1 to enable display panel Video 1 input jack. 040 AUTO CAMPORT 0/1 1 Set to 1 to automatically switch to Camport.
Installer Menu Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The POWER MANAGE function is for saving energy. If set to 0, Power Manage is Off.
Installer Menu 011 - KEY DEFEAT (Keyboard Defeat) If set to 1, key defeat prevents the end user from accessing the onscreen menus with the display front panel—MENU, SELECT, and Left / Right arrow keys do not function. If set to 0, those keys do function. NOTE: The menus can always be accessed by pressing MENU on the remote. 015 - SLEEP TIMER If set to 1, the SLEEP TIMER feature may be used. If set to 0, the Sleep Timer is not available.
Installer Menu Detailed Descriptions of Installer Menu Items 047 - AUX STATUS Set to 1 for M.P.I. AUX source to be reported as a channel number instead of channel 0. Set to 0 to disable AUX identification change. Controls M.P.I. status channel response for AUX inputs. 053 - DIS. CH-TIME (Disable Channel-Time) Set to 1 to disable the Channel-Time display, Channel-Time display will not appear. Set to 0 to enable the Channel-Time display. 069 - EN. CH-T COL.
Installer Menu 093 - RJP AVAILABLE (Remote Jack Pack Available) 0 = Remote jack pack is not available or disabled. 1 = Series 100 RJP, HDMI Mode Enables RJP when an HDMI cable is inserted into RJP. Video is from HDMI. Audio stream is expected from HDMI source. If no audio is present, no audio will be heard. 2 = Series 100 RJP, DVI Mode Enables RJP when an HDMI cable is inserted into RJP. Video is from HDMI however, Audio is from selected audio source, based on the RJP’s audio hierarchical priority.
Reference: Clonable Menu Features Clonable Menu Features Menu /Sub Menu Features Setup SET ID Audio Audio Language EZ SoundRite EZ sound Balance Treble Bass Front Surround TV Speaker BBE Time Auto Clock Auto Off Option Aspect Ratio Caption Caption Mode DTV Captions Style DTV Captions Style DTV Captions Style DTV Captions Style DTV Captions Style DTV Captions Style DTV Captions Style DTV Captions Style DTV Captions Style Language Cinema ISM Method Low Power - Style Size Font Text Color Text Opacity BG Co
Reference: Procedures for adding Channel Label Icons/Custom Channel Labels (2-5-4 + MENU Mode) Adding Channel Icons and Labels in the 2-5-4 + Menu Mode Editing/Adding Channel ICONs and/or Labels If there is no pre-assigned ICON, you can make a custom channel label of up to 7 characters to help in identifying the channel or network. At your option, channel labels can also be added in addition to a pre-assigned ICON.
Reference: Detailed Information For Making A Master TV IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING... To set up a master TV you will need to know how to enter the TV Installer menu and make changes to the default values as required. If necessary, familiarize yourself with the TV Installer menu and how to make and save changes in the menu, before attempting to clone the TV Master TV setup.
Reference: Checking Software Version Procedure for Checking Software Version The software version of the TV may be checked by accessing the INSTALLER MENU. To do this, press the MENU button repeatedly until the menu display ceases to respond to MENU key presses. Then, press "9", "8", "7", "6", "ENTER/SELECT". PTC INSTALLER MENU 000 INSTALLER SEQ 000 UPN 000-000-000-000 FPGA E0F1 PTC V1.00.000 CPU V3.06.
TV Camport Auto Sense Operation The CAMPORT Auto Sense function is enabled when: 1. Installer Menu Item 34, CAMPORT EN is set to 1 AND 2. Installer Menu Item 40, AUTO CAMPORT is enabled (1). Selectable= Can be accessed with INPUT key, direct access, etc. Auto Sense= Switches to this input when connector is inserted. The camport (Front Video) has the highest priority and will override any commands including tuning to the Start Channel.
TV Aux Input Configuration / Troubleshooting Troubleshooting Some quick and easy tips to resolving problems Symptoms Possible Cause(s) Possible Solution(s) See Page(s) Channel not included in channel scan in TV controller. After 2-5-5 + MENU, only channels included in TV controller will appear. 6 If channel is available it can be added to channel scan. If it is not available, the ‘No Signal’ message appears on the TV screen. Software Problems Cannot direct enter channel number or “No Signal” appears.
Troubleshooting Some quick and easy tips to resolving problems Symptoms Possible Cause(s) Possible Solution(s) See Page(s) Power No Power. See troubleshooting flow chart. 24 Display Panel Picture No Picture. • Display panel is turned off. • • • • • Antenna/Cable not connected. Connections incorrect. M.P.I. not connected. Encrypted program. Wrong tuning band. -Turn TV on. -Power failure? -Connect Antenna/Cable signal to TV. -Check connections on TV. -If applicable, connect M.P.I. cable to M.P.I.
Reference: Cloning Procedure Troubleshooting Warning: Do not use LT2002 while any PPV card is installed in TV or clone programmer will be damaged. Note Reset Clone After Static Shock After replacing exhausted batteries, or if the programmer behaves strangely after a static shock, use a paper clip or similar instrument inserted through the small hole marked ”RESET” to activate the internal reset switch and restore normal operation. After a reset, check the real-time clock setting.
Troubleshooting Flow Chart Controller Quick Check Is 'STATUS' LED on Analog Board Blinking ? No Yes Is TV Connected to AC Power ? No Plug into AC Power Outlet Press 'POWER' or 'ON/OFF' key on TV Yes Bad TV Did TV Turn On ? No 1. Bad TV Yes Is Red LED on TV Lit ? No Press 'POWER' or 'ON/OFF' or 'VOLUME UP/DOWN' or 'MUTE' key on Installer Remote 1. Bad Analog Board. 2. Bad Digital Board. Yes Did TV Respond ? Cycle the power by removing and re-connecting the AC power cord.
Commercial Mode Check Press the "On/Off" key on the front panel. The On/Off key is always operational. Did you get a response ? No Bad TV Yes Leave the TV set On Go to Installer menu by pressing "MENU" until the TV stops responding. Did TV stop responding or continue to respond ? Stopped responding TV is in Commercial Mode.
Reference: RJP Mode Configuration PAGE 26 206-4071
Glossary of Terms A list of definitions for some of the words found in this guide 75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire sticking through the middle. It screws onto the Antenna/Cable threaded jack on the back of the TV. 300 TO 75 OHM ADAPTER A small device that connects a twowire 300 ohm antenna to a 75 ohm RF jack.
For Customer Support/Service Please call: 1-888-865-3026 www.lgcommercial.com Marketed and Distributed in the United States by LG Electronics U.S.A., Inc. 1000 Sylvan Avenue Englewood Cliffs, NJ 07632 206-4100 © Copyright 2008, LG Electronics U.S.A., Inc.