User’s Guide W1542S W1742S W1941S Make sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. See the label attached on the product and give the information to your dealer when you ask for service.
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit.
Important Precautions Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures which may result in a fire hazard. Therefore, NEVER: Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front 2. Assemble the Stand Body into the facing downward on a soft cloth. monitor in the correct direction as shown in the picture. Stand Body 3. Assemble the Stand Base into the Stand Body in the correct direction. Stand Base Base Lock 4. Tie down the Base Lock to perpendicularity direction. 5.
Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on a flat 2. Place the monitor face down as shown surface. in the picture. 3. Change your lock on the monitor as it follows and turn it in the arrow direction. If you can't release the Stand Base even the Locking Knob is at a release position, Please push the indicated knob down and retry it. Locking Knob 4. Pull out the Stand Base to remove.
Connecting the Display 5. Pushing the PUSH button, take the Stand Body from monitor. WARNING You can hurt your finger. Good Position Bad Position Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort.
Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect signal input cable 1 and power cord 2 in order, then tighten the screw of the signal cable. A Connect D-sub(Analog signal) Cable (PC) B Connect D-sub(Analog signal) Cable (MAC) NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown.
Control Panel Functions Front Panel Controls 1 2 4 : 3 in Wide Button 3 4 5 It allows you to adjust the size of screen you are watching now. • WIDE : Switch to full screen mode according to input image signal. • 4 : 3 : Change the image signal ratio into 4:3. 4 : 3 IN WIDE 4 : 3 IN WIDE WIDE 4:3 WIDE mode 4 : 3 display mode MENU Button Use this button to enter or exit the On Screen Display.
Control Panel Functions Buttons Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page 15. AUTO/SET Button Use this button to enter a selection in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode).
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments.
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus.
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE BRIGHTNESS To adjust the brightness of the screen. CONTRAST To adjust the contrast of the screen. GAMMA Set your own gamma value. : -50 / 0 / 50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR PRESET Select the screen color.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description TRACKING HORIZONTAL To move image left and right. VERTICAL To move image up and down. CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters.
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description SETUP MENU : Exit : Adjust : Adjust SET : Select another sub-menu LANGUAGE To choose the language in which the control names are displayed. OSD POSITION To adjust position of the OSD window on the screen. WHITE BALANCE If the output of the video card is different the required specifications, the color level may deteriorate due to video signal distortion.
On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you press the front of the monitor. button on the Menu Name Icons Sub-menu Name FLATRON F-ENGINE Screen when applied Screen when not applied When you execute F-ENGINE, two tones will appear on the screen as shown. The applied screen will appear on the left side, whereas the non-applied screen will appear on the right side. Press the SET button to use the adjusted screen.
Troubleshooting Check the following before calling for service. No image appears ● Is the power cord of the • Check and see if the power cord is connected properly to the power outlet. display connected? ● Is the power indicator light on? • Press the Power button. ● Is the power on and the • Adjust the brightness and the contrast.
Troubleshooting Display image is incorrect ● Display Position is incorrect. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. ● On the screen background, vertical bars or stripes are visible. • Press the AUTO/SET button to automatically adjust your display image to the ideal setting.
Troubleshooting Display image is incorrect ● The screen color is mono or abnormal. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel - Settings. ● The screen blinks. • Check if the screen is set to interlace mode and if yes, change it to the recommend resolution.
Specifications W1542S Display 15 inches (38.1 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size: 38.1 cm 0.2595*0.2595 mm pixel pitch Sync Input Horizontal Freq. Vertical Freq. Input Form Video Input Signal Input Input Form 30 - 61 kHz (Automatic) 56 - 75 Hz (Automatic) Separate Sync. SOG (Sync On Green) 15 pin D-Sub Connector RGB Analog (0.
Specifications W1742S Display 17 inches (43.3 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size: 43.3 cm 0.255*0.255 mm pixel pitch Sync Input Horizontal Freq. Vertical Freq. Input Form Video Input Signal Input Input Form 30 - 83 kHz (Automatic) 56 - 75 Hz (Automatic) Separate Sync. SOG (Sync On Green) 15 pin D-Sub Connector RGB Analog (0.
Specifications W1941S Display 18.51 inches (47.0 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size: 47.0 cm 0.30*0.30 mm pixel pitch Sync Input Horizontal Freq. Vertical Freq. Input Form Video Input Signal Input Input Form 30 - 61 kHz (Automatic) 56 - 75 Hz (Automatic) Separate Sync. SOG (Sync On Green) 15 pin D-Sub Connector RGB Analog (0.
Specifications Preset Modes (Resolution) W1542S Display Modes (Resolution) 1 2 3 4 5 6 7 8 9 *10 11 VGA VGA VGA VESA VESA VESA MAC VESA VESA VESA VESA Horizontal Freq. (kHz) Vertical Freq. (Hz) 31.469 31.468 31.469 37.500 37.879 46.875 49.725 48.363 60.123 44.772 56.
Specifications W1941S Display Modes (Resolution) 1 2 3 4 5 6 7 8 *9 VGA VGA VESA VESA VESA MAC VESA VESA VESA Horizontal Freq. (kHz) Vertical Freq. (Hz) 31.468 31.469 37.500 37.879 46.875 49.725 48.363 60.123 47.
Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the interchange device. 1. Place the monitor with its front facing downward on a soft cloth. 2. Pushing the PUSH button, take the Stand Body from monitor. 3. Install the Wall mount plate. Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate.
Digitally yours