STAREX-IS BSM Manual Fig. 4.4-24 Result of SLPA BLOCK Command 4.4.4.8. SLPA UNBLOCK Command Function to unblock SLPA. Command : UBLK-SLPA:BSC=a,SMP=b,SLPA=c,[SLV=d]; a : BSC Number(00~11) b : SMP Number(00~04) c : SLPA Number(00~17) d : SLV Number(00~03) Input : UBLK-SLPA:BSC=0,SMP=0,SLPA=0,SLV=0; Fig. 4.4-25 Result of SLPA UNBLOCK Command 4.4.4.9. VCPA BLOCK Command Function to block VCPA.
STAREX-IS BSM Manual b : VMP Number(00~07) c : VCPA Number(00~15) d : SLV Number(00~01) e : DSP Number(00~03) Input : BLK-VCPA:BSC=0,VMP=0,VCPA=0,SLV=0,DSP=0; Fig. 4.4-26 Result of VCPA BLOCK Command 4.4.4.10.
STAREX-IS BSM Manual Fig. 4.4-27 Result of VCPA UNBLOCK Command 4.4.4.11. VLIA BLOCK Command Function to block VLIA. Command : BLK-VLIA:BSC=0,VMP=0,VLIA=0,[E1=0],[TS=1]; a : BSC Number(00~11) b : VMP Number(00~07) c : VLIA Number(0~1) d : E1 Number(00~15) e : TS Number(00~31) Input : BLK-VLIA:BSC=0,VMP=0,VLIA=0,E1=0,TS=1; Fig. 4.4-28 Result of VLIA BLOCK Command 4.4.4.12.
STAREX-IS BSM Manual c : VLIA Number(0~1) d : E1 Number(00~15) e : TS Number(00~31) Input : UBLK-VLIA:BSC=0,VMP=0,VLIA=0,E1=0,TS=1; Fig. 4.4-29 Result of VLIA UNBLOCK Command 4.4.4.13. H/W RESET BSC Device Command Function to reset BSC Device on H/W Level.
STAREX-IS BSM Manual Fig. 4.4-30 Result of BSC Device H/W Reset Command 4.4.4.14. H/W RESET ALPA Command Function to reset ALPA on H/W Level. Command : RMT-ALPA:BSC=0,ALMA=0,ALPA=0,CLS=HARDRST; a : BSC Number(00~11) b : ALMA ID(0~1) c : ALPA ID(0~4) d : Class(HARDRST,ISOLAT,UNISOL) Input : RMT-ALPA:BSC=0,ALMA=0,ALPA=0,CLS=HARDRST; Fig. 4.4-31 Result of H/W RESET ALPA Command 4.4.5. Bts Device Status Control 4.4.5.1.
STAREX-IS BSM Manual Input : DIS-BTS-DEV:BSC=0,BTS=0,PROC=CRP; Fig. 4.4-32 Result of BTS Device Status Display Command 4.4.5.2. FA Status Display Command Function to display FA Status. Command : DIS-FA-STS:BSC=a,BTS=bFA=c; a : BSC Number(00~11) b : BTS Number(00~47) c : FA Number(0~7) Input : DIS-FA-STS:BSC=0,BTS=0,FA=0; SMD-011-PMA210 Page:404(877) Issue:1.
STAREX-IS BSM Manual Fig. 4.4-33 Result of FA Status Display Command 4.4.5.3. BLOCK DBPA Command Function to block DBPA. Command : BLK-DBPA:BSC=a,BTS=b,RCP=c,DBPA=d,[CHIP=e],[CONDITION=f]; a : BSC Number(00~11) b : BTS Number(00~47) c : RCP Number(0~5) SMD-011-PMA210 Page:405(877) Issue:1.
STAREX-IS BSM Manual d : DBPA Number(0~9) e : CHIP Number(0~1) f : Select Option(conditional, unconditional) Conditional : If there is call connected, wait until it is disconnected during timeout and then block it. If it is not disconnected until timeout, do not block it. Unconditional : block a call regardless of their presence unconditionally. (The existing call is disconnected) Reference : If an OverHead Channel is allocated, do not block a call unconditionally.
STAREX-IS BSM Manual Fig. 4.4-35 Result of UNBLOCK DBPA Command 4.4.5.5. BLOCK OverHead Channel Element Display Command Function to block OverHead Channel Element Command : BLK-OVHD-CE:BSC=a,BTS=b,SECTOR=c,FA=d; a : BSC Number(00~11) b : BTS Number(00~47) c : SECTOR(ALPHA,BETA,GAMMA,DELTA,EPSILON,ZETA) d : FA Number(0~5) Input : BLK-OVHD-CE:BSC=0,BTS=0,SECTOR=ALPHA,FA=0; Fig. 4.4-36 Result of BLOCK OverHead Channel Element Display 4.4.5.6.
STAREX-IS BSM Manual Command : UBLK-OVHD-CE:BSC=a,BTS=b,SECTOR=c,FA=d; a : BSC Number(00~11) b : BTS Number(00~47) c : SECTOR(ALPHA,BETA,GAMMA,DELTA,EPSILON,ZETA) d : FA Number(0~5) Input : UBLK-OVHD-CE:BSC=0,BTS=0,SECTOR=ALPHA,FA=0; Fig. 4.4-37 Result of UNBLOCK OverHead Channel Element 4.4.5.7. H/W RESET BTS Device Command Function to reset BTS Device on H/W.
STAREX-IS BSM Manual Fig. 4.4-38 Result of H/W RESET BTS Device Command 4.4.5.8. H/W RESET LPA Device Command Function to reset LPA Device on H/W.Level Command : RMT-LPA:BSC=a,BTS=b,SECTOR=c,LPA=d,CLS=e; a : BSC Number(00~11) b : BTS Number(00~47) c : SECTOR(ALPHA,BETA,GAMMA,DELTA,EPSILON,ZETA) d : LPA Number(0~5) e : Class(HARDRST,ISOLAT,UNISOL) Input : RMT-LPA:BSC=0,BTS=0,SECTOR=ALPHA,LPA=0,CLS=HARDRST; Fig. 4.4-39 Result of H/W RESET LPA Device Command SMD-011-PMA210 Page:409(877) Issue:1.
STAREX-IS BSM Manual 4.4.5.9. H/W RESET LPA Combiner Command Function to reset the LPA Combiner on H/W Level Command : RMT-LPA-COM:BSC=a,BTS=b,SHELF=c,COM=d,CLS=e; a : BSC Number(00~11) b : BTS Number(00~47) c : SHELF Number(0~5) d : Combiner Number(0~2) e : Class(HARDRST,ISOLAT,UNISOL) Input : RMT-LPA-COM:BSC=0,BTS=0,SHELF=0,COM=0,CLS=HARDRST; Fig. 4.4-40 Result of LPA Combiner H/W RESET Command 4.4.5.10.
STAREX-IS BSM Manual Fig. 4.4-41 Result of BTS SHELF POWER H/W RESET Command 4.4.6. Status Message Control Table 4.4-5 Status Message LIST Codes Definition Description S3002 CAN CNP/PNP Status Change When Processor Status changes, it occurs. Display S3003 AMP Status Change Display When Processor Status changes, it occurs. S3004 ALP Status Change Display When Processor Status changes, it occurs. S3005 CCP Status Change Display When Processor Status changes, it occurs.
STAREX-IS BSM Manual S3209 PCP BCRA Status Change Displayed upon device status change BCRA Status Change Displayed upon device status change Display S3210 PMP Display S3211 AMP GPSR Status Change Displayed upon device status change Display S3220 NCP ASIA Status Change Display Displayed upon device status change S3221 NCP ASCA Status Change Displayed upon device status change ATSA Status Change Displayed upon device status change ALMA Status Change Displayed upon device status change Dis
STAREX-IS BSM Manual 4.4.6.1. Inhibited Status Message Display Command Function to display Status Message whose display to Outterm is inhibited Command : DIS-INH-STS; Input : DIS-INH-STS; Fig. 4.4-42 Result Inhibited Status Message Display Command 4.4.6.2. Status Message Display Inhibition Command Function to inhibit Status Message display Command : INH-STS-MSG:SN=a; a: SN Number(ALL,S3002~S3020,S3201~S3230, S3501,S3502) Input : INH-STS-MSG:SN=S3002; Fig. 4.
STAREX-IS BSM Manual 4.4.6.3. Allow Inhibited Message Command Function to allow display of Status Message whose display to Outterm is inhibited Command : ALW-STS-MSG:SN=a; a: SN Number(ALL,S3002~S3020, S3201~S3230, S3501,S3502) Input : ALW-STS-MSG:SN=S3002; Fig. 4.4-44 Result of Inhibited Message Display Allow Command 4.4.7. Overload Status Control 4.4.7.1.
STAREX-IS BSM Manual Fig. 4.4-45 Result of Processor Overload Status Display Command 4.4.7.2. Overload Threshold Value Display Command Function to display Overload Threshold Value Command : DIS-OVLD-THR:BSC=a,[BTS=b],PROC=c; a : BSC Number(00~11) b : BTS Number(00~47) c : Processor Name(CCP,BSP) Input : DIS-OVLD-THR:BSC=0,BTS=0,PROC=BSP; SMD-011-PMA210 Page:415(877) Issue:1.
STAREX-IS BSM Manual Fig. 4.4-46 Result of Overload Threshold Value Display Command 4.4.7.3. Overload Threshold Value Change Command Function to change Overload Threshold Value. Command: CHG-OVLD-THR:BSC:a,[BTS=b],LEVEL=c,[LOAD=d], [ORG_PER=e],[TER_PER=f]; a : BSC Number(00~11) b : BTS Number(00~47) c : LEVEL(0~100) d : LOAD(0~100) e : ORG_PER(0~100) f : TER_PER(0~100) Input : CHG-OVLD-THR:BSC:0,BTS=0,LEVEL=0,LOAD=100, ORG_PER=97,TER_PER=100; SMD-011-PMA210 Page:416(877) Issue:1.
STAREX-IS BSM Manual Fig. 4.4-47 Result of Overload Threshold Value Change Command 4.4.7.4. Overload Generation Test Command Function to generate Overload threshold value Command : STRT-OVLD-GEN:BSC=a,[BTS=b],PROC=c,LEVEL=d; a : BSC Number(00~11) b : BTS Number(00~47) c: Processor Name(CCP,BSP) d: LEVEL(0~24) Input : STRT-OVLD-GEN:BSC=0,BTS=0,PROC=BSP,LEVEL=0; Fig. 4.4-48 Result of Overload Generation Test Command 4.4.7.5. Overload Generation Test STOP Command SMD-011-PMA210 Page:417(877) Issue:1.
STAREX-IS BSM Manual Function to stop the Overload Generation Test Command : STOP-OVLD-GEN:BSC=a,[BTS=b],PROC=c,LEVEL=d; a : BSC Number(00~11) b : BTS Number(00~47) c: Processor Name(CCP,BSP) d: LEVEL(0~24) Input : STOP-OVLD-GEN:BSC=0,BTS=0,PROC=BSP,LEVEL=0; Fig. 4.4-49 Result of Overload Generation Test STOP Command 4.4.7.6.
STAREX-IS BSM Manual Fig. 4.4-50 Command to Determine Whether to Perform the Overload Generation Test SMD-011-PMA210 Page:419(877) Issue:1.
STAREX-IS BSM Manual 4.5. Test Command 4.5.1. On-Line Test-related Command On-Line Test is a function that allows a test to be performed automatically at a specific time on a specific day and includes the following: Vocoder, CE, BTS Markov test and VSWR test. The tests of CE, BTS Markov and VSWR find out presence of faults in hardware of Channel Elements in BTS and the test function for radio environment, and the Vocoder test finds out presence of faults in hardware of Vocoder in BSC.
STAREX-IS BSM Manual b: BSC number (0~11) c: BTS number (0~47) • Input/Output Fig. 4.5-1 Result of Test Inhibit Command Execution 4.5.1.2. On-Line Test Allow Command Function that allows Online Test for CE, Vocoder, BTS Markov, and VSWR test For CE, BTS Markov and VSWR test, input the corresponding BTS number and for Vocoder test, input corresponding BSC number.
STAREX-IS BSM Manual Fig. 4.5-2 Result of Test Allow Command Execution 4.5.1.3. On-Line Test Inhibit Item Display Function Function to display the inhibit of the on line test for the specific tests among the online tests by BSC and BTS. For Vocoder test, it displays Inhibit status. In case of CE, BTS Markov and in case of the VSWR test, it displays the status by BTS.
STAREX-IS BSM Manual Fig. 4.5-3 Result of Test Inhibit/Allow List Display Command Execution SMD-011-PMA210 Page:423(877) Issue:1.
STAREX-IS BSM Manual 4.5.2. Test-related to Channel Element Channel Element Test is performed in BIT(Built In Test) for each chip. The types of BIT Test are as follows: - Bus Interrupt Test - ChipX16 Test - PP2S Test - PCG Test This BIT Test is normally performed on Chip with OVHD channel and Chip seized with a call and the result is reported to BSM. Table 4.
STAREX-IS BSM Manual Fig. 4.5-4 Result of CE BIT Test Execution SMD-011-PMA210 Page:425(877) Issue:1.
STAREX-IS BSM Manual 4.5.3. Vocoder Test Function The types of Vocoder Tests are as follows: o DSP H/W Test - Determines the presence of problems in ROM, RAM, ALU of DSP in Vocoder - Diagnosis the presence of problems by checking Checksum, Read/Write, Flag Set, etc. - Caused by defective DSP Chip o Timing Module Test (Channel Test) - VCP generates Vocoder and Tx.Rx Timing by using MFP(MultipleFunction Processor) in order to exchange voice data with SLP every 20ms.
STAREX-IS BSM Manual FLT_DSP_HW DSP HW test Fault FLT_CLK Timing Module test Fault FLT_VCPA_LOOPBACK Vocoder Processor Loopback test Fault FLT_VCMA_LOOPBACK Vocoder Master board Loopback test Fault FLT_VLIA_LOOPBACK Vocoder Line interface Loopback test Fault FLT_QCELP_ST0 Qcelp Algorithm test Fault state0 FLT_QCELP_ST1 Qcelp Algorithm test Fault state1 FLT_QCELP_ST2 Qcelp Algorithm test Fault state2 FLT_QCELP_ST3 Qcelp Algorithm test Fault state3 4.5.3.1.
STAREX-IS BSM Manual Fig. 4.5-5 Result of On-Demand Vocoder Test(Channel Type) Execution SMD-011-PMA210 Page:428(877) Issue:1.
STAREX-IS BSM Manual Fig. 4.5-6 Result of On-Demand Vocoder Test(DSP Type) Execution 4.5.3.2. Parameter Change Command Related to On-Line Vocoder Test Function to change On-Line Vocoder test start/ending time, test day and the scope of VMP/VCP to be tested.
STAREX-IS BSM Manual Fig. 4.5-7 Result of On-Line Vocoder Test parameter Change Command Execution Fig. 4.5-8 Result of On-Line Test at the time of On-Line Vocoder Test Execution SMD-011-PMA210 Page:430(877) Issue:1.
STAREX-IS BSM Manual Parameter Change 4.5.3.3. Parameter Display Command related to On-Line Vocoder Test Function to display On-Line Vocoder test start/ending time, test day, and the scope of VMP/VCPto be tested. • Command DIS-VCE-PARA:BSC=a; a: BSC number (0~11) • Input/Output Fig. 4.5-9 Result of On-Line Vocoder Test Parameter Display Command Execution 4.5.3.4.
STAREX-IS BSM Manual • Input/Output Fig. 4.5-10 On-Line Vocoder Test Result Display Command 4.5.3.5. Display Command of On-Line Vocoder Test Status Function to display the On-Line Vocoder Test performance status and to stop the test. If Item Field is designated as “DISPLAY”, it displays On-Line Vocoder test status of the present corresponding BSC, and if it is designated as "END_ONL", it stops current On-Line test.
STAREX-IS BSM Manual Fig. 4.5-11 On-Line Vocoder Test End Command, Status Display Command Execution Result SMD-011-PMA210 Page:433(877) Issue:1.
STAREX-IS BSM Manual 4.5.4. Link Test Function Link test is divided into PING test, IPC test, ATM Path test, and Trunk BER test. PING test checks the Link status of Application Level by using Ping command from Master Processor to each Target Processor. IPC test checks the presence of problems in LINK by conducting IPC Test to the mounted processors/devices. ATM Path test checks presence of faults in ATM LINK Level by conducting ATM Layer Test on the mounted Processor/Devices.
STAREX-IS BSM Manual Fig. 4.5-12 Result of Trunk BER Test Performance 4.5.4.2. PING Test Function Function to check Link Status for the Target Processor by the Master Processor that was input to MMI of BSM by using the Ping command Ping test is divided into Point To Point Test and Point To Multi Test.
STAREX-IS BSM Manual e: SMP number(0~5) f: VMP number(0~7) g: PCF number(0~2) • Input/Output Fig. 4.5-13 Result of PING Test Performance 4.5.4.3. IPC Test Function Function to check the presence of problems in the Link status between Processor/Device by executing IPC command of Application Level . IPC Test is divided into PTP test and PTM test.
STAREX-IS BSM Manual e: SMP number(0~5) f: VMP number(0~7) g: PCF number(0~2) • Input/Output Fig. 4.5-14 Result of IPC Test Performance 4.5.4.4. ATM Path Test Function Function to check presence of problems in Link Status between Processor and Device by executing ATM CC, LB, PM command. It is divided into PTP Test and PTM Test.
STAREX-IS BSM Manual d: Test Level(F4: VPC, F5: VCC) e: BSC number(0~11) f: BTS number(0~47) g: SMP number(0~5) h: VMP number(0~7) i: PCF number(0~2) • Input/Output Fig. 4.5-15 Result of ATM Path(PM) Test Performance SMD-011-PMA210 Page:438(877) Issue:1.
STAREX-IS BSM Manual Fig. 4.5-16 Result of ATM Path(CC) Test Performance SMD-011-PMA210 Page:439(877) Issue:1.
STAREX-IS BSM Manual Fig. 4.5-17 Result of ATM Path(LB) Test Execution SMD-011-PMA210 Page:440(877) Issue:1.
STAREX-IS BSM Manual 4.5.5. Command related to BSC Virtual Call Test General mobile call is ㅡmade by MS, BSS(BSC, BTS), switching system interworking. Because the section between MS and BSS is the place where call environment setup function and modulation and demodulation of voice data are made including allocation of call resource necessary for radio communication, it is responsible for essential function in the mobile communication system.
STAREX-IS BSM Manual the original data to validate the quality of voice. (FER measured at SLP) • Data Rate User can designate voice data rate to be used for testing call. The data rate is divided into the following: Full rate, Half rate, Quarter rate, Eighth rate, and Variable rate. 4.5.5.1. BSC Virtual Call Setup Function Function to designate various options and setting up Call to a specific MS or all the MSs MS to be tested should be entered to BSM DB with INS-TEST-MS command.
STAREX-IS BSM Manual Fig. 4.5-18 BSC Virtual Call Setup Command INTERM Display Fig. 4.5-19 Console Window Display at the setup of BSC Virtual Call SMD-011-PMA210 Page:443(877) Issue:1.
STAREX-IS BSM Manual Fig. 4.5-20 Display at the Termination of BSC Virtual Call 4.5.5.2. Virtual Call Release Function Function to release a call for a specific MS or all the MSs where a virtual call set up. The output resulting from virtual call release is displayed by "Release by MMC". • Command REL-TEST-CALL :BSC=a ,BTS=b [,TEST_KEY=c]; a: BSC number (0~11) b: BTS number (0~15) c: TEST KEY(1~100) • Input/Output Fig. 4.5-21 Result of BSC Virtual Call Release Command Execution 4.5.5.3.
STAREX-IS BSM Manual Fig. 4.5-22 Presently registered Testing MS Display 4.5.5.4. MS Supplementary Function Function to register MS to be used for the BSC Virtual test. For a test of virtual call, first register MS. • Command INS-TEST-MS :BSC=a ,BTS=b ,TEST_KEY=c [,MSIN=d]; a: BSC number (0~11) b: BTS number (0~47) c: TEST KEY(1~100) d: IMSI of MS • Input/Output SMD-011-PMA210 Page:445(877) Issue:1.
STAREX-IS BSM Manual Fig. 4.5-23 Testing MS Insert Result Display 4.5.5.5. MS Delete Function Function to delete MS registered on the test list of BSC Virtual Call • Command DEL-TEST-MS :TEST_KEY=a; a: TEST_KEY of Mobile to be deleted • Insert/Output Fig. 4.5-24 Delete MS Execution Result SMD-011-PMA210 Page:446(877) Issue:1.
STAREX-IS BSM Manual 4.5.6. TRAFFIC PATH TESTING FUNCTION it is a test enabling to decide if there is presence of failure with designated traffic path by setting a traffic path for BSC virtual call for a specific MS with the designated call resources and then measuring PER.. The kinds of virtual call include Markov and Loop Back., There are 8K and 13K respectively by service option. Call resources that the user can designate are as follows: Selector Slave Processor, Trunk, and BTS channel Chip.
STAREX-IS BSM Manual Fig. 4.5-25 Traffic Path Setup Command Execution Result Display(Interm Window) Fig. 4.5-26 Traffic Path Setup Command Execution Result Display(Console Window) 4.5.6.2. Traffic Path Release Function Function to release a Call to MS of a specific BSC, BTS where a virtual call is set up. • Command REL-PATH-CALL :BSC=a ,BTS=b; a: BSC number (0~11) b: BTS number (0~15) • Input/Output SMD-011-PMA210 Page:448(877) Issue:1.
STAREX-IS BSM Manual Fig. 4.5-27 Traffic Path Release Command Execution Result Display(Interm Window) Fig. 4.5-28 Traffic Path Release Command Execution Result Display(Console Window) SMD-011-PMA210 Page:449(877) Issue:1.
