Lexmark Confidential until announced RFID UHF option Setup Guide www.lexmark.
Lexmark Confidential until announced Safety information Refer service or repairs, other than those described in the user documentation, to a professional service person. CAUTION—SHOCK HAZARD: Make sure that all external connections (such as Ethernet and telephone system connections) are properly installed in their marked plug-in ports. CAUTION—POTENTIAL INJURY: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Lexmark Confidential until announced Contents Safety information.............................................................................2 Setting up the RFID UHF option ......................................................5 Checking the box contents................................................................................................................................................5 Accessing the system board to install internal options........................................................
Lexmark Confidential until announced 4
Lexmark Confidential until announced Setting up the RFID UHF option Checking the box contents Notes: • You must have a 250- or 500-sheet drawer installed on the printer to load RFID labels and print tags. • This option works with all LexmarkTM T64x series printers, except the Lexmark T640rn. The RFID UHF option comes in a box with other items needed for installation.
Lexmark Confidential until announced Accessing the system board to install internal options CAUTION—SHOCK HAZARD: Turn the printer off, and unplug the power cord from the wall outlet before continuing. If you have any other devices attached to the printer, turn them off as well and unplug any cables going into the printer. Note: Use a #2 Phillips screwdriver to remove the system board cover. 1 Push the release latch, and then lower the multipurpose feeder tray.
Lexmark Confidential until announced 7 Use the following illustration to locate the appropriate connector. Warning—Potential Damage: System board electrical components are easily damaged by static electricity. Touch something metal on the printer before touching any system board electronic components or connectors. Installing flash memory and firmware cards 1 Unpack the flash memory and firmware cards.
Lexmark Confidential until announced 3 Push the flash memory card firmly into place, and then release the locking clips. 4 Holding the firmware card by the locking clips, align the plastic pins on the card with the holes on the system board. 5 Push the firmware card firmly into place beside the flash memory card, and then release the locking clips. Notes: • The entire length of the connector on the flash memory and firmware cards must touch the system board and be locked into the connector.
Lexmark Confidential until announced 3 Unpack the interface card. 4 Align the connection points on the card with the connector on the system board, and push the card firmly into the system board connector. 5 Insert the screw saved from the cover plate (or the extra screw shipped with the card). 6 Tighten the screw to secure the card. Note: The Lexmark T642 and T644 have two card connectors. The interface card must be installed into the left connector, which is the closest to the controller card.
Lexmark Confidential until announced 5 Close the top front cover. 6 Close the multipurpose feeder. Installing the RFID UHF option The RFID UHF option is positioned under the printer, or, if a duplex unit is installed, it is positioned under the duplex unit. 1 Remove all packing material and tape from the RFID UHF option. 2 Disconnect all cables from the printer. 3 Separate the printer from the 250- or 500-sheet drawer. 4 Place the RFID UHF option on top of the 250- or 500-sheet drawer.
Lexmark Confidential until announced 5 Place the printer on top of the RFID UHF option. 6 Do not reconnect the cables until after the RFID cable is connected. For more information, see “Connecting the RFID cable” on page 11. Connecting the RFID cable 1 Unpack the RFID cable. 2 Attach one end to the RFID UHF option.
Lexmark Confidential until announced 3 Attach the other end to the printer. 4 Reconnect all other cables to the printer, and then turn the printer on. The printer is now ready to print with the RFID UHF option. Installing the fuser wiper 1 Unpack the fuser wiper. 2 Locate the fuser wiper cover latch on the right side of the printer. 3 Squeeze the buttons together, and then lift the right end of the fuser cover to remove it. 4 Pull the cover out to the right.
Lexmark Confidential until announced 6 Replace the old fuser wiper with the new one. 7 Replace the fuser wiper cover.
Lexmark Confidential until announced Choosing output and input devices Choosing an output device Output devices used in printing labels include the output expander, high-capacity output stacker, adjustable stacker, and 500-sheet RFID drawer. Choose an output device based on the software program, the length of label needed, and the number of labels that you expect to print at one time. To order an output device, visit the Lexmark Web site at www.lexmark.com.
Lexmark Confidential until announced Preparing to print Loading RFID labels To load labels: Note: Do not remove a tray when a job is printing or when the operator panel indicator light is blinking. Doing so may cause a jam. 1 Remove the tray from the printer, and place it on a flat, level surface. 2 Squeeze the side guide tab, and slide the guide to the outer edge of the tray. 3 Flex the label sheets back and forth to loosen them, and then fan them. Do not fold or crease the label sheets.
Lexmark Confidential until announced 4 Place the label sheets with the print side facing down and the labels positioned at the front of the tray. Note: When loading labels, leave at least 1 inch of space between the top of the label stack and the top of the drawer. Overloading may cause paper jams or damage to the labels. 5 Squeeze the rear guide tab, and slide the guide to the correct position for the size label sheets you are loading. 6 Insert the tray into the printer.
Lexmark Confidential until announced Printing Identifying rejected labels When a label is rejected, a unique defective tag marking pattern or symbol appears at the bottom of the label sheet as shown in the following diagram. Note: A pattern or symbol appears only if Yes is selected from the Mark on Error menu.
Lexmark Confidential until announced Understanding the RFID menu Configuring RFID-specific settings The RFID menu is used to configure RFID-specific settings. Note: RFID settings appear on the menu settings page. For information on printing a menu settings page, see the User's Guide available on the Software and Documentation CD. Press to access the Menu options. Select RFID Menu from the list. The RFID Menu settings appear.
Lexmark Confidential until announced Stop on Error Menu selection Purpose Option Comments Stop on Error Yes No Determines whether to stop printing and post a message on the display when the Retry Count is exhausted Yes is the factory default setting. Reject Bin Menu selection Purpose Option Comments Reject Bin Disabled Standard Bin Bin 1 Bin 2 Bin 3 Bin 4 Disabled is the factory default setting. Determines where to send sheets with RFID tags that failed to program correctly.
Lexmark Confidential until announced Understanding RFID printer messages RFID error messages Message Action 1 2 3 4 5 6 44.00 RFID error (generic) 44.01 Bad tag error Turn the printer off. Unplug the power cord from the wall outlet. Check all cable connections. Connect the power cord to a grounded outlet. Turn the printer on. If the message recurs, contact Customer Support, and report the message number and a description of the problem. • Cancel the current job and reprint.
Lexmark Confidential until announced RFID service messages Message Action 1 2 3 4 902.81 Service engine software error 982.xx Tray controller card error 985.01 Unable to communicate with interface card 985.02 Unable to communicate with radio 985.03 Radio fails internal self test Turn the printer off. Unplug the power cord. Check all cable connections. Make sure the RFID UHF option is positioned under the printer, or, if a duplex unit is installed, it is positioned under the duplex unit.
Lexmark Confidential until announced Notices Product information Machine type: 4061 Model(s): RF1 Edition notice February 2008 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Lexmark Confidential until announced UNITED STATES GOVERNMENT RIGHTS This software and any accompanying documentation provided under this agreement are commercial computer software and documentation developed exclusively at private expense. Federal Communications Commission (FCC) compliance information statement This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Lexmark Confidential until announced Exposure to radio frequency radiation The radiated output power of this device is far below the radio frequency exposure limits of the FCC and other regulatory agencies. A minimum separation of 20 cm (8 inches) must be maintained between the antenna and any persons for this device to satisfy the RF exposure requirements of the FCC and other regulatory agencies.
Lexmark Confidential until announced A declaration of conformity with the requirements of the directives is available from the Director of Manufacturing and Technical Support, Lexmark International, S. A., Boigny, France. This product satisfies the limits of EN 55022; safety requirements of EN 60950; radio spectrum requirements of ETSI EN 302 208; and the EMC requirements of EN 55024, ETSI EN 301 489-1 and ETSI EN 301 489-3. Česky Společnost Lexmark International, Inc.
Lexmark Confidential until announced Polski Niniejszym Lexmark International, Inc. oświadcza, że niniejszy produkt jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português A Lexmark International Inc. declara que este este produto está conforme com os requisitos essenciais e outras disposições da Diretiva 1999/5/CE. Slovensky Lexmark International, Inc.
Lexmark Confidential until announced Index Numerics 44.xx 20 902.xx 21 985.xx 21 B box contents 5 C contents, box 5 E emission notices 23, 24, 25 F FCC notices 23, 24 flash memory and firmware cards installing 7 removing packaging 7 fuser wiper installing 12 I identifying rejected labels 17 input device choosing 14 interface card installing 8 removing packaging 8 L labels loading 15 tag orientation 15 loading labels 15 O output device choosing 14 P printer messages 44.xx 20 902.xx 21 985.