Integration Instructions

ManualsBrandsLexmark International ManualsElectronicsUHF RFID Option

Table Of Contents

The Lexmark UHF RFID Module is designed for OEM Installation only into Lexmark compatible tray options only. The module

transmits in the frequency range of 902 - 928 MHz and is designed to function in the RF Exposure Category General

Population/Uncontrolled Environment. Thus the installer should ensure that exposure by personnel while testing and operation of

this module should maintain a distance of 20CM from the antenna.

This device complies with part 15 of the FCC Rules and Industry Canada license – exempt RSS Standards. Operation is subject to

the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation of the device.

A minimum separation distance of 20 CM must be maintained between the antenna and the person for this appliance to satisfy the

RF exposure requirements.

Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could

void the User’s authority to operate the equipment.

The module and its antenna must not be co-located or operated in conjunction with any other antenna or transmitter.

OEM Module Assembly and integration instructions follow:

OEM module Integration Instructions

Rev. Date: 21 Sept 2016 Pg 1

Integration into PN:

40C0745 or 40C0747

Name: 550 Tray ASM RFID

Lxk contact: Ward Inabinet (859-227-

4670)

Summary of content (14 pages)

PAGE 1
OEM module Integration Instructions Integration into PN: 40C0745 or 40C0747 Name: 550 Tray ASM RFID Rev. Date: 21 Sept 2016 Pg 1 Lxk contact: Ward Inabinet (859-2274670) The Lexmark UHF RFID Module is designed for OEM Installation only into Lexmark compatible tray options only. The module transmits in the frequency range of 902 - 928 MHz and is designed to function in the RF Exposure Category General Population/Uncontrolled Environment.
PAGE 2
ASSEMBLY INSTRUCTIONS PN: 40C0745 or 40C0747 Name: 550 Tray ASM RFID ID PN & Description Qty A 40C2100-Option ASM 1 Rev. Date: 15 Sept 2016 Pg 2 Lxk contact: Ward Inabinet (859-2274670) 1. Receive packaged Option. Open Box. A B C D E F 2. Remove foam packing sides and bag. Store for later reuse. Option on flat, clean surface.
PAGE 3
ASSEMBLY INSTRUCTIONS PN: 40C0745 or 40C0747 Name: 550 Tray ASM RFID (NA or EU) ID PN & Description Qty A 3087791 or 3087808 1 Rev. Date: 15 Sept 2016 Lxk contact: Ward Inabinet (859-2274670) 1. CS72x Option and RFID Module (A) shown. B C A D E F 2. Open Option Tray and remove corrugated insert. Discard insert.
PAGE 4
ASSEMBLY INSTRUCTIONS PN: 40C0745 or 40C0747 Name: 550 Tray ASM RFID (NA or EU) ID PN & Description Qty A Metal screw 2 B Plastite Screw 1 D E F Description F1 T1 Power Driver 2. Unfasten screws and remove Right Cover. Store cover and screws for later re-assembly. Pg 4 Lxk contact: Ward Inabinet (859-2274670) 1. Remove Tray completely from Option. Place Tray aside. C Tool / Fixture ID Rev.
PAGE 5
ASSEMBLY INSTRUCTIONS PN: 40C0745 or 40C0747 PN & Description ID Name: 550 Tray ASM RFID (NA or EU) Qty Rev. Date: 15 Sept 2016 Lxk contact: Ward Inabinet (859-2274670) 1. Note Option PCBA and cables on right side. A B C D E F 2. Carefully disconnect indicated cable. Note: significant force is required.
PAGE 6
ASSEMBLY INSTRUCTIONS PN: 40C0745 or 40C0747 PN & Description ID A Name: 550 Tray ASM RFID (NA or EU) Qty 1. Access Option Tray. Slide paper restraints fully to left and rear sides. B C D E F Tool / Fixture ID F1 T1 Description 2. Slide RFID module into Tray. Gently push RFID module down until fully seated. Slide side and rear restraint fully against RFID module. Rev.
PAGE 7
ASSEMBLY INSTRUCTIONS PN: 40C0745 or 40C0747 PN & Description ID Rev. Date: 15 Sept 2016 Name: 550 Tray ASM RFID (NA or EU) Qty Pg 7 Lxk contact: Ward Inabinet (859-2274670) 1. A B C D E F Cable exit Tool / Fixture ID Description Tray side F1 T1 Note the cables exiting the RFID module flow out to the rear of the Tray. Note that the “Bumpers” of the RFID module engage the Tray side and Tray restraints.
PAGE 8
ASSEMBLY INSTRUCTIONS PN: 40C0745 or 40C0747 PN & Description ID Name: 550 Tray ASM RFID (NA or EU) Qty Rev. Date: 15 Sept 2016 Pg 8 Lxk contact: Ward Inabinet (859-2274670) 1. Free ends of cables from Module are placed into Option. A B C D E F 2. USB cable exits through the rear of Option. Rear cover can slide out for USB cable exit.
PAGE 9
ASSEMBLY INSTRUCTIONS PN: 40C0745 or 40C0747 PN & Description ID A Name: 550 Tray ASM RFID (NA or EU) Qty Rev. Date: 15 Sept 2016 Pg 9 Lxk contact: Ward Inabinet (859-2274670) 1. Module power cable is routed through Option frame hole adjacent to Option PCBA. B C D E F 2. Connect Option Cable that was disconnected from PCBA into module connector. Connect free module cable into PCBA connector.
PAGE 10
ASSEMBLY INSTRUCTIONS PN: 40C0745 or 40C0747 PN & Description ID Name: 550 Tray ASM RFID (NA or EU) Rev. Date: 15 Sept 2016 Pg 10 Lxk contact: Ward Inabinet (859-2274670) Qty A B C notch D notch cavity E F Tool / Fixture ID Description F1 T1 1. Route excess cable length through notches in Option frame. Place excess cable into indicated cavity.
PAGE 11
ASSEMBLY INSTRUCTIONS PN: 40C0745 or 40C0747 Name: 550 Tray ASM RFID (NA or EU) ID PN & Description Qty A Metal screw 2 B Plastite Screw 1 C 3088231 label 1 1. Re-install Option Right Cover. D E F 2. Note USB cable exit path. 3. Apply 3088231 label Tool / Fixture ID Description F1 T1 Lexmark Confidential Rev.
PAGE 12
ASSEMBLY INSTRUCTIONS PN: 40C0745 or 40C0747 PN & Description ID Name: 550 Tray ASM RFID (NA or EU) Qty Rev. Date: 15 Sept 2016 Pg 12 Lxk contact: Ward Inabinet (859-2274670) 1. Perform a “Soft Power off” to the CS725 Test Printer. Place completed RFID Option over a Standard Option and under a CS725 printer. (Function Test set-up). A B C D E F 2. While pressing the “3” and “6”, perform a “Soft Power On” to the CS725 Test Printer. The printer will power on in the “Diagnostic Mode”.
PAGE 13
ASSEMBLY INSTRUCTIONS PN: 40C0745 or 40C0747 PN & Description ID Name: 550 Tray ASM RFID (NA or EU) Qty Rev. Date: 15 Sept 2016 Pg 13 Lxk contact: Ward Inabinet (859-2274670) 1. Load about 20 pages of RFID media into the Standard Option. 2. While pressing the “3” and “6”, perform a “Soft Power On” to the CS725 Test Printer. The printer will power on in the “Diagnostic Mode”. Scroll down and select “RFID Test”. A B 3. Select “Test Page 1”. Test page one will print out.
PAGE 14
ASSEMBLY INSTRUCTIONS PN: 40C0745 or 40C0747 Rev. Date: 15 Sept 2016 Name: 550 Tray ASM RFID (NA or EU) ID PN & Description Qty A 3088223-RFID Option Sheet 1 B 3088232-RFID Carton Label 2 C 40C9200-Forms Card 1 Pg 14 Lxk contact: Ward Inabinet (859-2274670) 1. Repackage Option. D E F 2. Place Set-Up sheet (A) and Forms Card (C) into Option Packaging. Tape Carton. Print out the RFID Option Carton label (B) and affix over the original Carton label.