Instruction Manual

Note: Please keep this instruction manual, it contains important information.
This product is covered by our 3-month warranty.
For any claim under the warranty or after sale service, please contact your distributor and present a
valid proof of purchase. Our warranty covers any manufacturing material and workmanship defect,
with the exception of any deterioration arising from the non-observance of the instruction manual
or from any careless action implemented on this item (such as dismantling, exposition to heat and
humidity, etc.). It is recommended to keep the packaging for any further reference. In a bid to keep
improving our services, we could implement modication on the colours and the details of the prod-
uct shown on the packaging.
WARNING! Not suitable for children under 3 years. Choking Hazard - Small parts.
Reference: RC50_10
© Lexibook®
FCC NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
WARNING: Changes of modications to this unit not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
Made in China, Shantou.
Lexibook S.A.
6 avenue des Andes
Bâtiment 11
91940 Les Ulis
France
Lexibook Limited
Unit 8-9, 4th Floor
Kenning Industrial Building
19 Wang Hoi Road
Kowloon Bay, Kowloon
Hong Kong
format: Leaet (A3 size, Double Sides Printing )
Environmental Protection:
Unwanted electrical appliances can be recycled and should not be discarded along with regular household
waste! Please actively support the conservation of resources and help protect the environment by
returning this appliance to a collection centre (if available).
©Disney
Instruction manual
Mode d’emploi
Manual de instrucciones
RC50_10
ENGLISH
PLEASE READ BEFORE OPERATING THIS EQUIPMENT.
Before using the unit, be sure to read all operating instructions carefully. Please note that these are
general precautions and may not pertain to your unit.
1. Read this Instruction Manual before you attempt to connect or operate the appliance.
2. Keep these instructions in good condition. Heed all warnings. Follow all instructions.
3. Save this Instruction Manual for future reference.
4. The apparatus shall not be exposed to dripping or splashing and no objects lled with liquids, such
as vases, shall be placed on the product. Dry location use only.
5. No naked ame source, such as candles, should be placed on the product.
6. Children should be supervised to ensure that they do not play with the appliance.
7. Ventilation should not be impeded by covering the ventilation openings.
8. Only use accessories, which are specied by the manufacturer.
9. Use replacement parts, which are specied by the manufacturer.
10. Install the unit in accordance with the manufacturer’s instructions.
11. Place the unit where there is good ventilation. Place the system on a at, hard and stable surface.
Do not expose to temperatures above 104°F. Allow at least 4 inches clearance from the rear and
the top of the unit and 2 inches from each side.
12. Press the players buttons gently. Pressing them too hard can damage the player.
13. Dispose of used batteries in an environmental-responsible manner.
14. Always ensure that the product is unplugged from the electrical outlet before moving or cleaning.
Clean it with dry cloth only.
15. Turn off the product during lightning, storms or when it will not be used for long periods of time.
16. This product has no user-serviceable parts. Do not attempt to repair this product yourself. Only
qualied service personnel should perform servicing. Take the product to the electronics repair
shop of your choice for inspection and repair.
17. NEVER let anyone, especially children, push anything into holes, slots or any other openings in
the unit’s casing as this could result in a fatal electric shock.
18. Don’t mount this product on a wall or ceiling.
19. Do not place the unit near TVs, speakers and other objects that generate strong magnetic elds.
20. Do not leave the unit unattended when it is in use.
21. Keep minimum distances around the apparatus for sufcient ventilation.
22. The ventilation should not be impeded by covering the ventilation openings with items, such as
newspapers, table-cloths, curtains, etc.
23. The use of apparatus in moderate climates.
24. Batteries should be disposed properly. Take them to the collection container in order to protect the
environment.
SAFETY INSTRUCTIONS
POWER SUPPLY
Your RC car operates with a 6.0V Ni-MH rechargeable battery pack (5 x 1.2VAAA), 600mAh
(included), that can be charged with the 5.0 V 2.0A USB charging cable or adaptor plug (not
included).
The remote control operates with 2 x 1.5V AA/LR6 batteries (not included).
The watch remote control operates with a built-in 3.7V 150mAh rechargeable battery
(included), that can be charged with the 5.0 V 2.0A USB charging cable with positive
center or adaptor plug (not included).
Voiture télécommandée / RC car / Coche RC
2.4 G remote Watch remote control
2
Charging the car :
1. Check that the unit is switched off.
2. Using a screwdriver, open the battery door located at the rear of
the unit.
3. Delicately remove the rechargeable battery from the compart-
ment. Unplug it by pinching both sides of the connector (see
gure 1)
4. Insert the small end of the USB charging cable (included) into
the battery connector.
5. Connect the other end of the micro USB cable into the USB port
of your powered computer or USB type power adaptor and con-
nect it to a wall socket (see gure 2).
6. The LED indicator on the USB cable turns red when charging,
and turn off when fully charged.
Adaptor specications:
RC car:
Input Power: 100 V – 240 V ~ 50 / 60 Hz,
Output Power: 5.0 V
2.0A
USB cable (included): Input: 5.0 V
2.0A Output: 5.0 V 250mA
Watch remote control:
Input Power: 100 V – 240 V ~ 50 / 60 Hz,
Output Power: 5.0 V
2.0A with positive centre
GETTING STARTED
CONTENTS
When unpacking, ensure that the following elements are included:
1 x Extreme Crosslander® RC car 1 x 2.4 G remote control 1 x watch remote control
1 x rechargeable battery pack 1 x USB charging cable (for the car) 1 x USB charging cable (for
the watch remote control) 1 x instruction manual
WARNING: All packaging materials, such as tape, plastic sheets, wire ties and tags are not part
of this toy and should be discarded for your child’s safety.
Product Description
Please refer to drawings on page 1.
SPECIFICATIONS
Input power USB DC 5.0V 2.0A
Frequency range 2405 – 2475MHz
Transmission power -5dBm
MAINTENANCE AND WARRANTY
Only use a soft, slightly damp cloth to clean the unit. Do not use detergent. Do not to expose the unit
to direct sunlight or any other heat source. Do not immerse the unit in water. Do not dismantle or
drop the unit. Do not try to twist or bend the unit.
1. On/Off switch
2. Demo button
3. Light indicator
4. Mute button
5. Turn left/right
6. Twisting function
7. Forward/Backward
8. On/Off button
9. Light
10. Flexible rubber belt
11. Trimming nger ring
12. Finger key
Installing batteries in the 2.4 G remote control:
1. Using a screwdriver, open the battery door located at the rear of
the unit.
2. Insert 2 x 1.5V AA/LR6 batteries observing the polarity markings
inside the battery compartment.
3. Close the battery compartment and tighten the screw.
Charging the watch remote control:
1. Check that the unit is switched off.
2. Insert the small end of the USB charging cable (included) into the
battery connector situated on the side of the remote.
3. Connect the other end of the micro USB cable into the USB port of
your powered computer or USB type power adaptor and connect it
to a wall socket (see gure 2).
4. The LED indicator on the watch lights up (red) when the device is
charging, and turns off when fully charged.
RC car
3
6
4
2
5
7
8
9
10
12
11
1
The toy is only to be connected to Class II
equipment bearing the following symbol.
Note: Please note that the USB cables can be used for battery charging only and not for data
transfer.
Warning: Disconnect the adapter if the game is not used for a long period of time to prevent
overheating. When the game is powered by an adapter, do not play outside. Check the state of
the adapter and the connection cords regularly.
If their condition is deteriorating, do not use the adapter until it has been repaired. The toy shall
only be used with a transformer for toys. The adapter is not a toy. The device should be dis-
connected from the power supply to be cleaned if liquids are used for cleaning. The toy is not
intended for children under 3 years old. Misuse of transformer can cause electrical shock.
Parental advisory: transformer and adaptor for toys are not intended to be used as a toy. The
usage must be under parental advice.
Warning:
- Danger of explosion if battery is incorrectly replaced. Please only replace it with the same or
equivalent battery.
- The battery should not be exposed to high temperatures, such as sunlight, re or anything
similar.
- Signicant electromagnetic interference or electrostatic discharges may cause the device to
malfunction or lose data. If the device is not functioning correctly, switch it off and then on
again, or unplug the USB cable, or remove the batteries and insert them again.
- The normal function of the product may be disturbed by strong electromagnetic interference. If
so, simply reset the product to resume normal operation by following the instruction manual. In
case the function could not resume, please use the product in other location.
Non-rechargeable batteries are not to be recharged. Rechargeable batteries are to be removed from the toy before being
charged. Rechargeable batteries are only to be charged under adult supervision. Different types of batteries or new
and used batteries are not to be mixed. Only batteries of the same or equivalent type as recommended are to be used.
Batteries are to be inserted with the correct polarity. Exhausted batteries are to be removed from the toy. The supply
terminals are not to be short circuited. Do not throw batteries into a re. Remove the batteries if you are not going to use
the game for a long period of time. Battery shall not be exposed to excessive heat such as sunshine, re or the like.
Make sure the car and remotes are charged, then turn them on.
How to use with the remote control
• Direction guiding (buttons 5 and 7): control the direction of the car.
• Demonstration mode (button 2): the car will start running in all directions!
• Mute (button 4): Turn the sound on and off.
• Twisting function (button 6): change the twisting positions of the car.
The numbers are from the gure in “Product Description” part.
How to use the watch remote control
A B C
A. Put the thumb inside the bracelet hole.
B. Buckle the bracelet
C. Put the nger key on. Press the On/Off button for 2 seconds to turn the watch remote control on.
• Once it is on, the watch remote control is locked by default (xed lights). To unlock it, short press
the On/Off button again, and the lights will start ashing, indicating the remote is active.
• To go back to the locked mode, simply press the on/off button once more.
• Long press to turn off the watch remote control (no lights).
• The car must be ON for the watch remote control to function (if the car is not detected, all lights
will rapidly ash at the same time).
1. Keep the nger key pressed and swing upward to twist the car upward.
2. Keep the nger key pressed and swing downward to twist the car downward.
3. Tilt the st to the front to advance forward.
4. Tilt the st to the back to advance backward.
5. Tilt the st to the left to make the car slide to the left.
6. Tilt the st to the right to make the car slide to the right.
1
4
2
5
3
6
TROUBLESHOOTING GUIDE
Problems Causes Solution
The car has no
response
The car is out of
control, or the control
range is short.
1. The remote control fails to connect or the car
is on “OFF”.
2. The remote control and car batteries are
installed improperly.
3. The power of the rechargeable battery is
weak.
1. The batteries of the remote control are low.
2. There may be interference near the site.
1. Turn on the car and repeat the
operation of signal connecting.
2. Install the batteries according to
the polarity instructions (see power
supply section).
3. Fully charge the car battery.
1. Replace the remote control batter-
ies with new ones or charge the
battery pack.
2. Replace the battery.
Lexibook America Inc.
C/O Pramex International – Groupe BPCE
1251 Avenue of the Americas, 3rd Floor
New York, NY 10020
USA
USA & Canada
Please contact the following email address for service and technical
support:
E-mail: [e-mail]
FRANÇAIS
LIRE LES INSTRUCTIONS SUIVANTES AVANT TOUTE UTILISATION DE L’APPAREIL.
Lisez et suivez attentivement ces instructions an d’utiliser au mieux toutes les
fonctions qu’offre cet appareil. Merci de noter qu’il s’agit de précautions générales qui peuvent ne pas
s’appliquer à votre unité.
1. Lisez ces instructions avant toute utilisation ou connexion de l’appareil.
2. Conservez ces instructions en bon état. Tenez bien compte des mises en garde. Suivez les instru
tions.
3. Conservez ce mode d’emploi pour consultation ultérieure.
4. N’utilisez pas cet appareil près de l’eau ou à proximité d’objets remplis d’eau tels que des vases. A
conserver à l’abri de l’humidité.
5. Ne placez jamais d’objets enammés, tels que des bougies allumées, sur l’appareil.
6. Les jeunes enfants ne doivent pas utiliser l’appareil sans la surveillance d’un adulte.
7. L’aération ne doit pas être bloquée en obturant les sorties d’aération.
8. Utilisez uniquement les attaches/accessoires recommandés par le fabricant.
9. Utilisez les pièces de remplacement recommandées par le fabricant.
10. Installez en respectant les consignes du fabricant.
11. Placez l’appareil dans un lieu aéré, sur une surface plate, dure et stable. Ne pas exposer à une
température supérieure à 40°C/104°F. L’appareil doit être positionné de sorte à laisser un espace
de 10 cm / 4 pouces à l’avant et à l’arrière et de 5 cm / 2 pouces sur les côtés.
12. Appuyez délicatement sur les boutons. Une pression trop forte pourrait endommager l’appareil.
13. Respectez l’environnement : éliminez les piles par l’entremise des points de collecte prévus à cet
effet.
14. Assurez-vous toujours que le produit est débranché de toute source d’alimentation avant de le
déplacer ou de le nettoyer. Pour nettoyer l’appareil, utilisez uniquement un chiffon sec.
15. Débranchez l’appareil lors d’orages ou lorsque vous ne l’utilisez pas pendant une longue période.
16. Aucune pièce de ce produit ne peut être réparée par l’utilisateur. Seul un personnel de service
qualié peut s’en charger. Portez l’appareil à l’atelier de réparation électronique de votre choix
pour manutention ou réparation.
17. Ne laissez JAMAIS personne, et en particulier les enfants, mettre des objets dans les trous, dans
les fentes ou dans toute autre ouverture de l’appareil – cela pourrait causer une électrocution.
18. Ne montez pas cet appareil sur un mur ou un plafond.
19. Ne placez pas cet appareil à proximité de
TV, haut-parleurs ou tout autre objet à fort champ
magnétique.
20. Ne laissez pas l’appareil sans surveillance lorsqu’il est en marche.
21. Gardez une distance minimale autour de l’appareil pour une
aération sufsante.
22. Il convient de ne pas obstruer les ouvertures d’aération par des objets tels que journaux, nappes,
rideaux, etc.
23. L’appareil est destiné à être utilisé sous un climat tempéré.
24. Les piles doivent être jetées de façon conforme. Déposez-le
s dans des bacs de collecte prévus
an de protéger l’environnement.
INSTRUCTIONS RELATIVES À LA SÉCURITÉ
DESCRIPTION DU PRODUIT
Lors du déballage, assurez-vous d’avoir tous les éléments suivants :
1 x Voiture télécommandée Extreme Crosslander® 1 x télécommande
1 x télécommande montre 1 x batterie rechargeable 1 x Câble de charge micro USB (pour la
voiture) 1 x Câble de charge micro USB (pour la télécommande montre) 1 x Mode d’emploi
AVERTISSEMENT: Tous les matériaux d’emballage, comme le scotch, les feuilles en plastique,
les celles et les étiquettes ne font pas partie du produit et doivent être jetés.
1. Interrupteur On/Off
2. Bouton Demo
3. Indicateurs de lumière
4. Bouton Mute
5. Tourner à droite/gauche
6. Fonction Twist
7. Avancer/Reculer
8. Bouton On/Off
9. Lumière
10. Bracelet caoutchouc exible
11. Bague
12. Touche sur le doigt
ALIMENTATION
Votre voiture télécommandée fonctionne avec une batterie rechargeable 6.0V Ni-MH,
600mAh (5 x 1.2V AAA), qui peut être chargée avec le câble USB ou un adaptateur secteur (non
inclus) 5.0V 2.0A.
La télécommande opère avec 2 piles x 1.5V AA/LR6 (non incluses).
La télécommande montre fonctionne avec une pile intégrée de 3.7V
150mAh (inclue),
qui peut être chargée avec le câble USB 5.0V 2.0A avec centre positif (inclus)
ou un adaptateur secteur (non inclus).
2
Charger la voiture:
1. Assurez-vous que l’appareil soit éteint.
2. À l’aide d’un tournevis, ouvrir le compartiment des piles à
l’arrière de la voiture.
3. Enlever délicatement la batterie rechargeable du compartiment.
Débranchez-la en pinçant les deux côtés du connecteur.
4. Insérez la petite extrémité du câble de chargement micro-USB
dans le connecteur de la batterie.
5. Branchez l’autre extrémité du câble au port USB d’un ordinateur
ou sur un adaptateur USB connecté à une prise murale (voir
gure 2).
6. L’indicateur LED sur le port USB clignote lorsque la batterie
charge.
Installing batteries in the 2.4 G remote control:
1. Using a screwdriver, open the battery door located at the rear of
the unit.
2. Insert 2 x 1.5V AA/LR6 batteries observing the polarity markings
inside the battery compartment.
3. Close the battery compartment and tighten the screw.
Installation des piles dans la télécommande 2.4 G:
1. À l’aide d’un tournevis, ouvrir le compartiment des piles.
2. Insérer 2 piles 1.5V AA/LR6, en respectant la polarité indiquée au
fond du compartiment des piles.
3. Refermer le compartiment des piles et resserrer la vis.
1
Spécications de l’adaptateur
Voiture télécommandée :
Puissance d’entrée : 100 V – 240 V ~ 50 / 60 Hz,
Puissance de sortie : 5.0 V
2.0A
USB cable (included): Entrée: 5.0 V
2.0A Sortie: 5.0 V 250mA
Télécommande montre :
Puissance d’entrée : 100 V – 240 V ~ 50 / 60 Hz,
Puissance de sortie : 5.0 V
2.0A with positive centre
1
RC50_10IM2160_339_V02.indd 1 17/4/2020 6:32 PM
- Consult the dealer or an experienced radio/TV technician for help.