Installation Manual
3-Way Wiring - Digital/Smart Switch with DD0SR-01Z Coordinating
Remote Application:
3-Way Wiring - Digital/Smart Dimmer with DD0SR-01Z Coordinating
Remote Application:
3-Way Wiring - Digital/Smart Dimmer with DD0SR-01Z
Coordinating Remote Application:
DI-000-DD0SR-02B
TOOLS NEEDED TO INSTALL YOUR REMOTE
Slotted/Phillips Screwdriver Electrical Tape Pliers
Pencil Cutters Ruler
INSTALLING YOUR REMOTE
NOTE: Use check boxes when Steps are completed.
ONOFF
ONOFF
ONOFF
ONOFF
ONOFF
ONOFF
ONOFFONOFF
ONOFF
ONOFF
ONOFF
ONOFF
WARNING: TO AVOID FIRE, SHOCK OR DEATH; TURN
OFF POWER at circuit breaker or fuse and test that power
is off before wiring!
Step 1
INTRODUCTION
Decora Digital/Decora Smart Coordinating Switch Remote is designed to be
used for multi-location control of Leviton’s line of Decora Digital and Decora
Smart Switches allowing the lighting to be controlled from the main switch or
the remote location. Its stylish look is compatible with Leviton’s other Decora
devices and wallplates (sold separately). White face assembled on device with
ivory and light almond face plates included.
• Three way communication
• Ease of installation – No new wiring
FEATURES
Side Wire Connection
Side wire terminals accept
#14-12 AWG solid copper
wire only.
Back Wire Connection
Back wire openings accept
#14-12 AWG solid copper
wire only.
Preparing and connecting wires:
This remote can be wired using side wire terminal screws or
through backwire openings.
Step 3
5/8"
(1.6 cm)
Strip Gage
(measure bare
wire here)
3-Way or More Applications (Multi-location)
Universal Coordinating Switching Remote
Cat. No. DD0SR-01Z - 120VAC, 60Hz
INSTALLATION INSTRUCTIONS
WARNINGS AND CAUTIONS:
• TO AVOID FIRE, SHOCK OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
• To be installed and/or used in accordance with electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
• Decora
®
Digital/Decora Smart remotes are not compatible with standard 3-way or 4-way switches. They must be used with compatible Decora Digital/
Decora Smart devices for multi-location switching.
WARNINGS AND CAUTIONS:
• Use this device WITH COPPER OR COPPER CLAD WIRE ONLY.
• Use only one (1) Decora Digital/Decora Smart dimmer or switch in a multi-location circuit with up to 9 coordinating remotes.
NOTE: The remote(s) will turn the light on at the brightness level selected at the dimmer.
• Recommended minimum wall box depth for remotes is 2-1/2".
• Maximum wire length from dimmer or switch to all installed remotes cannot exceed 300 ft (90 m).
6
5
4
1
2
3
2
5
4
3
1
4-Way
1. First Traveler (note color)
2. Second Traveler (note color)
3. Neutral
4. Ground
5. Third Traveler (note color)
6.
Fourth Traveler (note color)
NOTE: The first and third traveler
wires are used to carry line power
to the other switch boxes.
3-Way
1. Line or Load (Tagged)
2. Neutral
3. Ground
4. First Traveler (note color)
5. Second Traveler (note color)
NOTE: The first traveler wire is
used to carry line power to the
other switch box.
Identifying your wiring application
(most common):
NOTE: If the wiring in the wall box does not resemble
any of these configurations, consult an electrician.
Step 2
IMPORTANT:
For 3-Way applications, note that one of the screw terminals from the old
switch being removed will usually be a different color (Black) or labeled
Common. Tag that wire with electrical tape and identify as the common
(Line or Load) in both the dimmer wall box and remote wall box.
For 4-Way applications, note that the old switch being removed will have
4 screws plus a ground screw. Tag the two wires connected to the two back
screw terminals.
Changing the color of your Remote:
Your remote may include color options. To change color of the face proceed
as follows:
1
2
Insert top tabs
and press in
bottom tabs to
attach
Push in sides at
bottom tabs and
pull outward to
release
• Make sure that the ends of the wires from the wall box are
straight (cut if necessary).
• Remove insulation from wires in the wall box as shown.
Cut
(if necessary)
Step 4a
Step 4b
Step 4b
Green
Ground
Green
Ground
Hot (Black)
Neutral (White)
DD0SR-01Z Coordinating Remote
YL/RD
YL/RD
RD
WH
RD
BK
Black
BK
WH
White
Line
120 VA
C
60Hz
(unused)
(unused)
Load
Digital/Smart Switch
Green
Ground
Green
Ground
Hot (Black)
Neutral (White)
DD0SR-01Z Coordinating Remote
YL/RD
YL/RvD
RD
WH
RD
BK
Black
BK
WH
White
Line
120 VAC
60Hz
(unused)
(unused)
Load
Digital/Smart Dimmer
Digital/Smart Switch
DD0SR-01Z
Coordinating Remote
Terminal
Screw
marked
Black (BK)
Terminal
Screw marked
Red (RD)
Terminal
Screw marked
White (WH)
Terminal
Screw
marked
Yellow/Red
(YL/RD)
Terminal
Screw marked
Red (RD)
2
4
2
4
1
WH
BK
RD
YL/RD
WH
BK
RD
YL/RD
1
Neutral to Terminal
Screw marked
White (WH)
3 3
5 5
Terminal
Screw
marked
Black (BK)
Terminal
Screw
marked
Y
ellow/Red
(YL/RD)
DD0SR-01Z
Coordinating Remote
Terminal
Screw marked
Red (RD)
2
4
1
WH
BK
RD
YL/RD
Neutral to Terminal
Screw marked
White (WH)
3
5
Terminal
Screw
marked
Black (BK)
Terminal
Screw
marked
Y
ellow/Red
(YL/RD)
Digital/Smart Dimmer
Terminal
Screw
marked
Black
(BK)
Terminal
Screw marked
Red (RD)
Terminal
Screw
marked
Yellow/
Red
(YL/RD)
4
BK
RD
YL/RD
1
3
5
2
NOTE: DDS15, DW15S, DH15S, DZ15S and DL15S are compatible with DD0SR-01Z.
NOTE: The DD0SR-01Z coordinating remote must be installed in a wall box with a Neutral connection.
WIRING DD0SR-01Z COORDINATING REMOTE (wall box with load connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE: "BK" and "RD" terminals on coordinating remote are unused. Tighten both screws.
• Green or bare copper wire in wall box to Green terminal screw.
• Load wall box wire identified (tagged) when removing old switch to First Traveler (note color as above).
• Second Traveler wall box wire (note color as above) to terminal screw marked
"YL/RD". This traveler from the remote must go to the terminal screw on the switch marked "YL/RD".
• Neutral wall box wire to terminal screw marked "WH".
WIRING DIGITAL/SMART SWITCH (wall box with line hot connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identified (tagged) when removing old switch to terminal screw marked "BK".
• First Traveler wall box wire to terminal screw marked "RD" (note wire color).
• Remove Red insulating label from terminal screw marked "YL/RD".
• Second Traveler wall box wire to terminal screw marked "YL/RD" (note wire color). This traveler from the
switch must go to the terminal screw on the remote marked "YL/RD".
• Neutral wall box wire to terminal screw marked "WH".
• Proceed to Step 5.
NOTE: DDL06, DDMX1, DDE06, DD710, DW6HD, DW1KD, DH6HD, DH1KD, DZ6HD, DZ1KD, DL6HD and
DL1KD are compatible with DD0SR-01Z.
NOTE: The Digital/Smart Dimmer must be installed in a wall box that has a Load connection. The DD0SR-01Z
coordinating remote must be installed in a wall box with a Neutral connection.
NOTE: When used with a Digital/Smart Dimmer, dimming can only be performed from the dimmer location.
WIRING DD0SR-01Z COORDINATING REMOTE (wall box with load connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE: "BK" and "RD" terminals on coordinating remote are unused. Tighten both screws.
• Green or bare copper wire in wall box to Green terminal screw.
• Load wall box wire identified (tagged) when removing old switch to First Traveler (note color as above).
• Second Traveler wall box wire (note color as above) to terminal screw marked "YL/RD". This traveler from
the remote must go to the terminal screw on the dimmer marked "YL/RD".
• Line Neutral wall box wire to terminal screw marked "WH".
WIRING DIGITAL/SMART DIMMER (wall box with line hot connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identified (tagged) when removing old switch to terminal screw marked "BK".
• First Traveler wall box wire to terminal screw marked "RD" (note wire color).
• Remove Red insulating label from terminal screw marked "YL/RD".
• Second Traveler wall box wire to terminal screw marked "YL/RD" (note wire color). This traveler from the
dimmer must go to the terminal screw on the remote marked "YL/RD".
• Neutral wall box wire to terminal screw marked "WH"
• Proceed to Step 5.
3-Way Wiring - DDL06 Dimmer with DD0SR-01Z Coordinating Remote
(no neutral) Application:
Step 4c
DD0SR-01Z
Coordinating Remote
Terminal
Screw marked
Red (RD)
2
WH
BK
RD
YL/RD
3
5
Terminal
Screw
marked
Black (BK)
Terminal
Screw
marked
Y
ellow/Red
(YL/RD)
DDL06 Dimmer
Terminal
Screw
marked
Black
(BK)
Terminal
Screw marked
Red (RD)
Terminal
Screw
marked
Yellow/
Red
(YL/RD)
4
BK
RD
YL/RD
1
3
5
2
4
1
Green
Ground
Green
Ground
Hot (Black)
Neutral (White)
DD0SR-01Z
Coordinating Remote
YL/RD
YL/RD
RD
RD
BK
Black
BK
WH
White
Line
120 VAC
60Hz
Load
DDL06 Dimmer
(unused)