Instructions / Assembly

47617
Technical Support: 800-824-3005
Customer Service: 800-722-2082
International: 425-486-2222
Fax: [phone]
Web: www.leviton.com
Recessed
Entertainment Box
with Low Prole
Frame
DI-001-47617-00A
STEP 1:
WARNING: TO AVOID FIRE, SHOCK, OR
DEATH; TURN OFF POWER at circuit breaker or
fuse and test that power is off before wiring!
STEP 2A:
Mounting: New Construction – Stud Mounted
Installation (refer to Figures 1A and 1B):
1. Select the desired location for installation.
2. Ensure that you allow for wallboard material
thickness when mounting.
NOTE: The frame will allow the hiding of minor
imperfections or visible holes after mounting of
wallboard around Entertainment Box. The maximum
margin on the backside of the frame to cover
wallboard is approximately 3/8” (0.95 cm). Refer to
Figures 1A and 1B.
3. Using two (2) supplied wood screws, secure the
enclosure to the stud thru the two (2) mounting
slots (refer to Figure 1A).
4. After wallboard material is installed with cut-out
approximately 8.0” (20.3 cm) x 7.2” (18.3 cm)
in proper location, mount the low profile
frame (refer to Figure 1B) or the optional high
profile frame with cover (not included, refer to
Figure 4) to the Entertainment Box.
5. Install four (4) #8 screws into the four frame holes
to secure frame.
NOTE: The #6 screws with swing clips are used only
when installing in a retrofit construction.
STEP 2B:
Retrofit Construction – Wall Mounted
Installation (refer to Figures 2A and 2B):
1. Select the desired location for installation.
NOTE: This installation requires mounting the
Entertainment Box in between the studs with a
minimum clearance of 11.0” [27.9 cm (refer to note in
Figure 2A)]. If necessary, use a stud finder to locate
and mark studs that are behind surface of wall.
2. Using the front of the Entertainment Box as a
template, trace the enclosure outline with
a pencil on the wall surface (refer to Figure 2A).
Using a wallboard saw, cut the opening out of the
wallboard surface.
NOTE: Make sure that you leave enough space
for a device box which may be attached to the
Entertainment Box (refer to Figure 3A). If space
between studs is less than 14.0” (35.6 cm), the
Entertainment Box must be mounted offset from
center-line of studs.
3. Select the low profile frame or the optional
high profile frame with cover (not included, refer
to Figure 4) for the installation. Assemble frame to
Entertainment Box using the four (4) #6 screws
and by placing them into the four frame holes.
Attach the supplied swing clips to each screw prior
to mounting (refer to Figure 2B). DO NOT tighten
screws all the way down at this point.
NOTE: Ensure that the swing clips are placed on the
screws in the orientation as depicted in Figure 2B for
proper wallboard mounting.
4. Mount the Entertainment Box into the wall
surface opening ensuring that the swing clips
are positioned flat on box (refer to Figure
2B Detail). Secure to wallboard by tightening all
four screws. Make sure the swing clips catch the
wall material in all four locations (refer to Figure 2B).
STEP 3A:
Wiring Application:
Line Voltage Connections (refer to Figure 3A):
1. Use a standard Carlon 1-Gang Device Box
(reference: Carlon p/n B114R).
2. Select the desired location on Entertainment Box
and insert the device box from the inside. Tighten
the two mounting screws on the device box to
secure it to the Entertainment Box.
3. Route the electrical wires to the device box.
Install the desired line voltage device to support
your application needs.
NOTE: Refer to the individual device installation
instructions for complete wiring instructions.
4. Install the appropriate standard size wallplate onto
the device box and device, if necessary.
NOTE: If using a Decora
®
style wallplate, ensure that
1/4” (0.64 cm) mounting screws are used to secure
wallplate.
5. Repeat steps 1 thru 4 to install additional devices
in other locations. Use the Snap-on Cover Plate
provided for unused openings.
STEP 3B:
Low Voltage Connections (refer to Figure 3B):
1. Use a 1-Gang Low-Voltage Bracket (reference:
Levion p/n C0224 or Carlon p/n B100R) for low-
voltage devices.
2. Select the desired location on Entertainment Box
and insert the Low-Voltage Bracket. Tighten the
two mounting screws on the Low-Voltage Bracket
to secure it to the enclosure.
3. Route the low-voltage cables/wires through the
bracket. Install the desired low-voltage device(s)
required to support your application needs.
NOTE: Refer to the individual device installation
instructions for complete wiring instructions.
4. Install the appropriate standard size wallplate onto
Low-Voltage Bracket, if necessary.
NOTE: If using a Decora
®
style wallplate, ensure that
1/4” (0.64 cm) mounting screws are used to secure
wallplate.
5. Repeat steps 1 thru 4 to install additional devices
in other locations. Use the Snap-on Cover Plate
provided for unused openings.
STEP 3C:
Component To Component Connections
(refer to Figures 3C and 3D):
1. To route low-voltage connections from component
to component, use the existing Snap-on Cover Plate.
2. Using a swedge knife, cut the knock-out from the
Snap-on Cover Plate (refer to Figure 3C).
NOTE: The knock-out size is 1.25” (3.2 cm) in diameter.
3. Gently pull low-voltage wires thru hole in Snap-on
Cover Plate. Snap the Cover Plate into the opening
and connect wires to appropriate application.
4. Repeat steps 1 thru 4 to run additional low-voltage
connections in other locations. Use the Snap-on
Cover Plate provided for unused openings.
Parts Included:
1) Recessed Entertainment Box (1)
2) LowProleFrame(1)
3) CoverPlate(1)
4) #10 Wood Screws (2)
5) #6 Screws (4)
6) SwingClip(4)
7) #8 Screws (4)
Tools needed to install your
Entertainment Box:
1) Slotted/PhillipsScrewdriver
2) ElectricalTape
3) WallboardSaw
4) Pencil
5) Cutters
6) Ruler
7) Swedge Knife
1
2
5
7
4
6
4
3