User's Manual

Self-powered Wireless Occupancy Sensor
Cat. Nos. WSC04-IxW & WSC15-IxW
PK-93682-10-02-0A
INSTALLATION
English
WARNINGS AND CAUTIONS:
• TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH ELECTRICAL CODES AND REGULATIONS.
• IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT AN ELECTRICIAN.
• TO BE USED FOR INDOOR APPLICATIONS ONLY(10-30°C ENVIRONMENTS).
• DO NOT EXPOSE THIS DEVICE TO DIRECT SUNLIGHT. IT IS INTENDED FOR INDOOR USE ONLY, WITH OPERATIONAL LIGHTING REQUIREMENTS FROM 4 TO 100 FOOT CANDLES (1000 LUX)
DO NOT EXPOSE THIS DEVICE TO CONDITIONS IN EXCESS OF 100 FC
DESCRIPTION:
The Wireless Occupancy Sensor is a solar powered & battery-free wireless transmitter that communicates with a wide variety of receivers. Each time motion is detected, the transmitter sends a wireless
signal that commands the receiver to turn a device off or on. A switch can also be added to control the lights.
COMPATIBLE DEVICES:
• 3-WireRelay    •5-WireRelay    •Plug-inDimmer/Relay
• 4-ChannelLowVoltageReceiver  •RoomController    •Thermostat
• Morereceiversavailable   •Wallboxreceiverswitch
EQUIPMENT NEEDED FOR INSTALLATION
• Slotted Screwdriver
• Phillips screwdriver
• Double Sided Foam Mounting Tape (Included - for “screwless” mounting)
• Wall Anchors and Screws (Anchors Not included - for “screw to” mounting)
• Ceiling Tile Stem, Nut, & Washer (Included - for “ceiling tile” mounting)
PROGRAMMING AND ACTIVATION:
1. Do not mount the sensor until after it has been programmed to communicate with all appropriate receivers.
2. Do not remove Test Cover until after it has been tested.
3. Make sure the sensor is within 16 feet (5 meters) of the desired receiver when programming.
3. Programming: To associate a sensor with a receiver, carefully remove the access door with a slotted screw driver,
then press the learn button on the Wireless Occupancy Sensor while the receiver is in the desired Program Mode (see receiver instructions for programming).
4. Activation:OnceanOccupancySensorhasbeenassociatedwithareceiver,itsloadwillturnoneachtimethesensorseldofviewisentered.
- In Auto on mode the sensor will turn the load on with initial motion and start the time delay. Time delay will reset every 60 seconds with occupancy.
 -InManualonmodethesensorwillstartthetimedelayatrstoccupancydetection.Timedelaywillresetevery60secondswithoccupancy.
PLEASE NOTE: Do not attempt to activate loads while receivers are in Program Mode or other devices could be accidentally added or deleted from memory. Receivers have reduced range during
programming. Wireless Occupancy Sensor start up time is 2-4 minutes out of the box depending on light source (keep this in mind while considering mounting location). Wireless Occupancy Sensor Self
Powered light requirements are approximately 20 foot candles for 3 hours every 24 hours (keep this in mind while considering mounting location). If these requirements cannot be met, consider utilizing
battery backup feature or the two pin 24 vdc connection located underneath the sensor as the power source for your application.
INSTALLATION
Wireless Occupancy Sensors can be mounted using screws, adhesive foam, or ceiling tile mounted using the provided ceiling tile stem, nut, & washer.
SCREW TO SURFACE MOUNT:
1. Select location for mounting of sensor. If necessary, drill pilot holes into the mounting surface.
2. Use the included screws to mount the wireless Occupancy Sensor to the surface (wall anchors [not included] can be used with these screws).
3. Remove the back cover of the sensor. Hold the back cover and body of the sensor and rotate until the two arrows line up and pull apart.
4. Install back cover of the ceiling sensor to desired location using the included screws, nuts and washers, or screws in combination with commercially available wall anchors.
5. Secure the sensor body to the back cover by aligning the arrows. Lock it by turning the sensor such that the arrows do not line up.
6. Rotate the sensor to the desired orientation.
SPECIFICATIONS
WSC04-IxW and WSC15-IxW
F.O.V.
WSC04=450 sq. feet - WSC15=1500 sq. feet
Frequency / Range 315 MHz / 50-150 feet
Power Supply Solar Powered, Battery for backup (not required)*
Channels 1 Channel
Output Channels Only limited by number of receivers in range
Addressing Factory set unique ID (1 of 4 billion)
Radio Certication FCC (United States) QGH-WSCR
I.C. (Canada) 2437A-WSCR
*Battery - 1/2 AA, 3.6v Lithium
ADHESIVE SURFACE MOUNT:
1. Remove backing material and apply double sided mounting tape to the Sensor Base.
2. Press and hold the Wireless Occupancy Sensor to the desired mounting surface for a few seconds before releasing.
CEILING TILE MOUNT:
1. Use the included ceiling tile stem to push through the ceiling tile in the desired location. Install the proper washer and nut above the ceiling tile to secure.
2. ConnectSensorBasetothestemandtwisttosecure,referenceguresbelowfordetails.
3. Rotate the sensor to the desired orientation. Note that the sensor base and back cover are keyed. To lock the device in place, ensure that the arrows are not aligned.
For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only)
www.leviton.com
LIMITED 2 YEAR WARRANTY AND EXCLUSIONS
LevitonwarrantstotheoriginalconsumerpurchaserandnotforthebenetofanyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperusefortwoyearsfromthepurchasedate.Leviton’sonly
obligation is to correct such defects by repair or replacement, at its option, if within such two year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201
North Service Road, Melville, New York 11747. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened,
abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and tness for a particular purpose, but if any implied
warrantyisrequiredbytheapplicablejurisdiction,thedurationofanysuchimpliedwarranty,includingmerchantabilityandtnessforaparticularpurpose,islimitedtotwoyears.Leviton is not liable for incidental, indirect, special, or consequential damages, including
without limitation, damage to, or loss of use of, any equipment, lost sales or prots or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
Leviton is a registered trademark of Leviton Mfg. Co. in the United States, Canada, Mexico,
and other countries. Other trademarks herein are the property of their respective owners.
These products are covered by one or more U.S. & Foreign Patents and Patents Pending
Copyright © 2010 Leviton Manufacturing Co., Inc.
All rights Including Trade Dress Rights Reserved
FCC COMPLIANCE STATEMENT:
FCC ID: QGH-WSCR IC: 2437A-WSCR
The enclosed device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(i.) This device may not cause harmful interference
(ii.) This device must accept any interference received, including interference that may cause undesired operation.
AnychangesormodicationsnotexpresslyapprovedbyLevitoncouldvoidtheuser’sauthoritytooperatethisequipment.
TROUBLESHOOTING :
1. Verify Red LED is blinking every 60 seconds with occupancy, this indicates the device is charged
and transmitting.
TESTING:
1. Ensure Test Cover is in place to control Test Environment:
a. Assure device pairing is properly completed.
b. Verify timeout/load off function occurs accurately.
c. Remove Test Cover and verify Auto-On responds energizing load(s).
2. Walktestthesensorforcorrecteldofviewandoperationwithinresponsiblespace.
a. Adjustsensorbyrotatingasneededtonetuneperformance.
Ceiling Tile Stem
Nut
Washer
Ceiling Tile
Ceiling Tile Mounted Sensor
Keylock Arrow
Test Cover
Sensor
Solar Cell
Ceiling Tile Stem Mounted
Installation sur dalles de plafond
Soporte de panel de techo
Tuerca
Arandela
Panel de techo
Flechas para asegurar
Cubierta de prueba
Sensor
Célula solar
Sensor de panel de techo montado
Sensor de panel de techo montado
Tige de suspension
Écrou
Rondelle
Dalle de
plafond
Flèches d’alignement
Couvercle protecteur
Détecteur
Photopile
Installation sur dalles de plafond
CEILING TILE MOUNT / INSTALLATIONS SUR DALLES DE PLAFOND / MONTAJE EN EL PANEL DE TECHO
Back Cover Open Center
Mounting Screw
Back Cover Internal
Surface Shown
Abertura central de la cubierta posterior
Tornillo de Montaje
Muestra la superficie interna
de la cubierta posterior
Couvercle arrière (intérieur)
Vis de montage
Ouverture centrale du couvercle arrière
Screw Mounted Sensor
Sensor Montado con Tornillos
Installation avec vis
Mounting Location
Sensor Back Cover
Keylock Arrow
Mounting Screws (2 places)
Nut (2 places)
Washer (2 places)
Solar Cell
Test Cover
Sensor / Détecteur / Sensor
Cubierta posterior
del sensor
Flechas para asegurar
Tornillo de montaje (2 lugares)
Locacion de montaje
Tuerca (2 lugares)
Arandela (2 lugares)
Célula solar
Cubierta de prueba
Emplacement choisi
Couvercle arrière
Flèches d’alignement
Vis de montage (2 endroits)
Écrou (2 endroits)
Rondelle (2 endroits)
Photopile
Couvercle protecteur
SCREW TO SURFACE MOUNT / INSTALLATIONS AVEC VIS / MONTAJE SUPERFICIAL CON TORNILLOS