Programmer/Remote Cat.
TABLE OF CONTENTS INTRODUCTION........................................................1 MENU NAVIGATION & ICONS..............................2–4 STARTUP...................................................................5 INSTALLATION CHECKLIST....................................5 Include Dimmers/Switches.....................................6 TEXT EDITOR....................................................6, 7 Include Controller............................................7, 8 Update Controller...............
INTRODUCTION Leviton’s Programmer/Remote, Cat. No. RZCPG, is a multifunctional device. It uses Z-WaveTM technology to act as a programmer, zone or scene controller, remote and timer for setting up and operating your ViziaTM RF network. This manual will guide you through the understanding of your RZCPG functions as a setup controller. Once your network is installed, your RZCPG may also be used as a wireless controller for activating events, and controlling your lighting system.
MENU NAVIGATION and ICONS Navigating screens and menus on your RZCPG is accomplished using the following buttons: LCD Display x1 (HOME screen depicted) 12:00 PM Mon 05.01.2006 Left Soft Key Default Profile Stand By Right Soft Key Menu Arrow Buttons (up, down, left, right) Center Button x1 1 ON "–" Button OFF 12:00 PM 2 ON x1 OFF Mon 05.01.200 6 12:00 PM 3 ON OFF 4 ON OFF "+" Button Mon 05.01.
<> appears on various screens as a prompt to create something new (Area, Profile, Event, etc.) x1 AREA << NEW >> Back x1 Home All Devices x1 Mon 05.01.200 6 Default Profile Stand By Menu Check boxes are used when multiple selections are All Devices Dimmer #1 available. Use the and x1 Switch #1 buttons to select and deselect 1 1 Switch #2 from a list.
ICON DESCRIPTION Undefined device Center button Single choice (radio button) - not chosen Single choice (radio button) - chosen Multiple selection (checkbox) - not selected Multiple selection (checkbox) - selected Remote Control Zone/Scene Controller (Single or Multibutton) Dimmer Switch Thermostat Event is Set Event Disabled or All Events are Disabled Buzzer OFF (indication) Buzzer OFF Buzzer ON Error Indication Event Recurrence One Time Event Date Event Time Time of Day or Dawn/Dusk Offset Filter (data o
STARTUP NOTE: Upon initial power up of x1 the RZCPG, the VIZIATMRF logo DATE & TIME will appear briefly and then the Time: 09: 00 AM DATE & TIME screen will display, Date: 06. 07. 2007 prompting the user to change Wednesday the settings. NOTE: Leviton Save Cancel recommends setting the date and time before proceeding. Failure to do so will disable your events (refer to EVENTS pg. 15). Set the date and time for your RZCPG as follows: x1 x1 12:00 PM Mon 05.01.
Using your RZCPG, follow these steps to set up your ViziaRFTM network: STEP 1 Include Dimmers/Switches Pressing the center button x1 to select Include Dim/Swch INCLUDE DIM/SWCH Press button on will bring you to the INCLUDE Dimmer/Switch DIM/SWCH screen and put the RZCPG into Inclusion Mode. You will be prompted to press a button on your Dimmer, Switch or Cancel Plug-In Module.
Default Profile Menu x1 x1 OFF OFF OFF OFF OFF OFF Menu Default Profile Stand By ON Menu OFF Default Profile Stand By ON Menu OFF 1 ON 1 ON 2 ON 2 ON 3 ON 3 ON 4 ON 4 ON Menu Stand By Default Profile Default Profile Stand By To create a unique name or modify text, under ABC (or Abc, abc, 123) use the up and down arrow buttons to change each letter or numeral and side arrow buttons to navigate. The and buttons can be used to insert and delete characters.
Once your name is displayed, x1 INCLUDE CNTRLLER press the center button .The Node included! RZCPG will confirm inclusion Node ID #3: and prompt you to continue to Room Controller INCLUDE CONTROLLER by More? Press pressing the center button or Back Next Step to continue to the Next step by pressing the right soft key NOTE: The confirmation process will take some time, specifically in large networks. Remain close to the controller until the confirmation is complete.
Continue this process until all of your controllers have been updated. Each time you successfully update your controller it will be removed from the list. Once all of your controllers have been updated, press the right soft key to continue to the NEXT STEP. x1 STEP 4 Create Areas INSTALL CHECKLIST NOTE: The INSTALL CHECKLIST screen will appear with the selection box around STEP 4 - Create Areas when NEXT STEP is chosen from STEP 2. Press the center button to bring up the AREA screen.
STEP 5 Set Associations OFF OFF OFF OFF OFF OFF OFF OFF Menu NOTE: The INSTALL INSTALL CHECKLIST CHECKLIST screen will appear 1. Include Dim/Swch with the selection box around 2. Include Controller 3. Update Controller STEP 5 - Set Associations 4. Create Areas when NEXT STEP is chosen 5. Set Associations from STEP 4. Back Next Step Press the center button to x1 bring up the ASSOCIATION ASSOCIATION screen.
STEP 6 Security OFF OFF OFF OFF OFF OFF OFF OFF Menu 1 ON 1 ON 2 ON 2 ON 3 ON 3 ON 4 ON 4 ON Menu Default Profile Stand By NOTE: The INSTALL INSTALL CHECKLIST CHECKLIST screen will appear 2. Include Controller with the selection box around 3. Update Controller 4. Create Areas STEP 6 - Security when NEXT 5. Set Associations STEP is chosen from STEP 5. 6. Security Press the center button to Back Next Step bring up the SECURITY screen. x1 Press the center button to select 1. Setup Password.