BLE-B8224 Module – Installation Manual FCC ID of this product is as follows: FCC ID: 2ASLN-ODS15 IC ID of this product is as follows: IC: 25037-ODS15 This module can be used for Bluetooth protocol. The module is tested in compliance with FCC part 15.247. It operates only in 2.4 GHz band [24002483.5 MHz]. For integration on Leviton’s end-product only – module cannot be sold to general public.
Contents 1. 2. 3. 4. 5. 6. 7. 8.
1. Supply Voltage • • 3 The power is provided from the 6-pin connector to the module. The module has on-board LDO to regulate power supply. Min. Typ. Max. Unit Operating Temperature Range -40 +25 +85 Deg. C Operating Voltage 2.8 5.0 7.
2. Theory of Operation – BLE Channels BLUETOOTH Channel # 37 0 1 2 3 4 5 6 7 8 9 10 38 11 12 13 14 15 16 17 Frequency (MHz) 2402 2404 2406 2408 2410 2412 2414 2416 2418 2420 2422 2424 2426 2428 2430 2432 2434 2436 2438 2440 TX Power Target MAX dBm (Dec) [Firmware Setting] 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.
3. Module Dimensions • The module is of fixed dimensions and no outside changes are permitted. • Refer to ‘B8224module.dxf’ for footprint.
2. Module Connections • Module can only be used with another PCBs connected using the 8-pin connector. • Keep area under the antenna clear of any copper or electrolytic components.
4. Antenna • The module comes with an embedded PCB antenna design that followed the specifications of the antenna. • About the signal line between PCB antenna on the module • It is a 50-ohm line design. • Fine tuning of return loss etc. can be performed using a matching network. However, it is required to check "Class1 change" and "Class2 change" which the authorities define then. • The concrete contents of a check are the following two points. 1.
4. Antenna • Please refer KDB 996369 D04 Module Integration Guide for guidance, installation instructions and testing requirements. • Conducted emissions testing: Option for Conducted Testing U.FL.
7. Notice • For Leviton’s end-product integration only – device cannot be sold to general public. • This module can be used either for Bluetooth protocol. The module is tested in compliance with FCC part 15.247. It operates only in 2.4 GHz band [2400-2483.5 MHz]. • Therefore we will include the following statements required by FCC/ IC on the product and in the Installation Manual Notice. • Please describe the following warning on the final product which contains this module.
7. Notice • Please describe the following warning to the manual. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le produit décrit aux présentes est conforme aux exigences de la partie 15 des règlements de la FCC.
7. Notice This device is intended only for Leviton end-product integrators under the following conditions: 1)The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2)The transmitter module may not be co-located with any other transmitter or antenna. 3)The use of an antenna with gain less than 1.5 dBi (2.4GHz).
7. Notice End-Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end-product must be labeled in a visible area with the following: “Contains FCC ID:2ASLN-ODS15”. “Contains IC: 25037-ODS15”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.
7. Notice Declaration of Conformity statement must be declared in the end-product user manual. FCC SUPPLIERS DECLARATION OF CONFORMITY Smart Wallbox Sensors manufactured by Leviton Manufacturing, Inc., 201 N Service Road, Melville, NY, http://www.Leviton.com. This device complies with part 15 of the FCC Rules.
8. End-product testing • During design process, • Designer of the host board should place the module at recommended location on the host board. • Designer should also perform the radiated regulatory FCC testing using manufacturer’s low-level radio test firmware to ensure compliance as per KDB 996369 D04. • Designer should also test for the applicable unintentional radiator functions (Part 15 Subpart B) of the end-product to ensure compliance as per KDB 996369 D04.
