User Manual

ManualsBrandsLester Electrical of Nebraska ManualsElectronicsData Collection Module

Operating Instructions 1 31083A

RF DATA COLLECTOR

MODEL 22240

FCC ID #OBH22240

PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS

For correct operation of the equipment, it is important to read and be familiar

with this entire manual before installing and operating the charger.

DO NOT DISCARD THIS MANUAL AFTER READING.

LOOK FOR THIS SYMBOL TO POINT OUT SAFETY PRECAUTIONS. IT MEANS:

BECOME ALERT—YOUR SAFETY IS INVOLVED. IF YOU DO NOT FOLLOW THESE

SAFETY INSTRUCTIONS, INJURY OR PROPERTY DAMAGE CAN OCCUR.

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

INSTALLATION INSTRUCTIONS

Tools needed to install RF Data Collector Model

22240: 11/32" nut driver, Phillips screwdriver,

Anderson Connector-Terminal Cable extractor

CAUTION: USE CAUTION WHEN WORKING

WITH INDUSTRIAL BATTERIES; THEY CAN BE

VERY DANGEROUS. INDUSTRIAL BATTERIES

CONTAIN ACID (ELECTROLYTE SOLUTION)

WHICH CAN CAUSE CHEMICAL BURNS AND

SERIOUS HARM TO SKIN AND EYES. ALWAYS

WEAR APPROVED PROTECTIVE EYE GOGGLES

AND RUBBER GLOVES. AVOID PROLONGED

BREATHING OF BATTERY VAPORS; WORK IN A

WELL-VENTILATED AREA. BATTERY VAPORS

CAN BE FLAMMABLE. DO NOT REST TOOLS

ON TOP OF BATTERY OR ALLOW ANY METAL

OBJECTS TO COME IN CONTACT WITH

BATTERY POSTS OR INTER-CELL

CONNECTORS.

ASSEMBLY PROCEDURE

1. Examine the cables between the battery and DC

plug. With caution, use the Anderson Terminal-

Cable extractor to remove only the positive

(RED) battery cable contact from the battery DC

plug housing.

2. From the RF Data Collector case assembly,

remove the bottom half of the case and the

plastic cord clamping device.

3. Carefully slide the positive (RED) cable contact

through the BLUE ring toroid, located in the top

half of case, with the ring "end" of the Data

Collector facing the battery. Reposition the RED

cable contact inside the battery DC plug

housing. Locate the RF Data Collector case top

(with LED facing up) close to the DC plug

housing and outside of all metal enclosures.

4. Lay the negative (BLACK) battery cable in the

area provided next to the positive (RED) cable.

5. Position the plastic battery cable clamp over

both of the wires so that the clamp slides easily

over the studs located in the RF Data Collector.

Verify that the arrows on top of the clamp point

toward the BLUE ring/battery end of the cables.

6. Using hand pressure only, carefully exert

downward force on the plastic battery cable

clamp until enough of the studs protrude through

the clamp to allow starting the hex nuts.

Exhibit 8

FCC ID#: OBH 22240

Summary of content (2 pages)

PAGE 1
8 RF DATA COLLECTOR Exhibit FCC ID#: OBH 22240 MODEL 22240 FCC ID #OBH22240 PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS For correct operation of the equipment, it is important to read and be familiar with this entire manual before installing and operating the charger. DO NOT DISCARD THIS MANUAL AFTER READING. LOOK FOR THIS SYMBOL TO POINT OUT SAFETY PRECAUTIONS. IT MEANS: BECOME ALERT—YOUR SAFETY IS INVOLVED.
PAGE 2
7. Tighten the hex nuts evenly. Never exceed 30 pound-inches of torque on the nuts. Failure to tighten the nuts evenly or overtightening can cause loss of electrical connection, part breakage, or cable damage. not blink, verify the polarity of connections to determine the cause. 11. During normal operation of the battery, the LED on the RF Data Collector will blink RED, indicating a run or discharge condition. The LED will blink GREEN while the battery is being charged. 8.