Users Manual

ManualsBrandsLeonton ManualsElectronicsWifi module

TLP3-71300-5120-24-T

FCC ID : 2AUYB-TXXX

802.11ac/abgnDual-Band

The MLC21AAM is a highly integrated module which has built in a 2x2 dual-band

wireless LAN radio. It supports IEEE 802.11ac draft standard and provides the highest

PHY rate up to 867Mbps, offering feature-rich wireless connectivity and reliable

throughput from an extended distance. Optimized RF architecture and baseband algorithms

provide superb performance and low power consumption. MLC21AAM integrates

PA/LNA such that the number of the external components is reduced to minimum.

Intelligent MAC design deploys a high efficient DMA engine and hardware data

processing accelerators which offloads the host processor. The MLC21AAM supports the

802.11i security standard and implements hardware acceleration for TKIP, CCMP and

WAPI.

General

Descriptions:

Summary of content (6 pages)

PAGE 1
TLP3-71300-5120-24-T FCC ID : 2AUYB-TXXX 802.11ac/abgnDual-Band General Descriptions: The MLC21AAM is a highly integrated module which has built in a 2x2 dual-band wireless LAN radio. It supports IEEE 802.11ac draft standard and provides the highest PHY rate up to 867Mbps, offering feature-rich wireless connectivity and reliable throughput from an extended distance. Optimized RF architecture and baseband algorithms provide superb performance and low power consumption.
PAGE 2
WLAN Base band MLC21AAM baseband supports the following features: 11ac stage-1 feature support 20, 40, and 80MHz channels MCS0-7 (BPSK, r=1/2 through 64QAM, r=5/6) MCS8-9 (256QAM, r=3/4 and r=5/6) VHT A-MPDU delimiter for RX and TX for single MPDU Clear Channel Assessment (CCA) on secondary Short Guard Interval STBC support Low Density Parity check (LDPC) coding Support digital pre-distortion to enhance PA performance Smoothing (channel estimation) extension to MIMO case Dynamic frequency selection (DFS) ra
PAGE 3
GENERAL IEEE WLAN Standard IEEE 802.11 a/b/g/n and 802.11ac draft compliant Support 20MHz, 40MHz, 80MHz in 5GHz band, and 20MHz, 40MHz bandwidth in 2.4GHz band Dual-band 2T2R mode with data rate up to 867Mbps Support 256QAM in 2.4GHz band Support STBC, LDPC, MRC, and transmit Beamforming Greenfield, mixed mode, legacy modes support Frame aggregation Integrated LNA, PA, and T/R switch. Optional external LNA and PA support. IEEE 802.11 d/e/h/i/k/r/w support Security support for WFA WPA/WPA2 personal, WPS2.
PAGE 4
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 5
This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module: KDB 996369 D03 OEM Manual v01 rule sections: 2.2 List of applicable FCC rules This module has been tested for complianceto FCC Part 15 2.3 Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition.
PAGE 6
B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable. As long as all conditions above are met, further transmittertest will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.