ThinkPad Edge 13″and E30 Hardware Maintenance Manual
ThinkPad Edge 13″and E30 Hardware Maintenance Manual
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 137. First Edition (December 2009) © Copyright Lenovo 2009. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents About this manual . . . . . . . . . . v Safety information . . . . . . . . . . 1 General safety . . . . . . . . . . . . . Electrical safety . . . . . . . . . . . . Safety inspection guide . . . . . . . . . . Handling devices that are sensitive to electrostatic discharge . . . . . . . . . . . . . . Grounding requirements . . . . . . . . . Safety notices (multilingual translations) . . . . . . . . . . . . . . . . . System . . . . . . . . . . . . . . . . . . . . . . . . 30 30 31 31 . 32 . 36 .
Windows 7 Professional (64 bit) DVDs . Common service tools . . . . . . . . . . . . 135 . 136 Notices . . . . . . . . . . . . . . 137 iv ThinkPad Edge 13″ and E30 Hardware Maintenance Manual Trademarks . . . . . . . . . . . . . .
About this manual This manual contains service and reference information for the following ThinkPad® products. ThinkPad Edge 13″ MT 0196, 0197, and 0492 ThinkPad Edge E30 MT 0196 Use this manual along with the advanced diagnostic tests to troubleshoot problems. Important: This manual is intended only for trained service technicians who are familiar with ThinkPad products. Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively.
vi ThinkPad Edge 13″ and E30 Hardware Maintenance Manual
Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad Notebook.
General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators – Similar units to listed above This practice ensures correct grounding of the units.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1.
Safety notices (multilingual translations) The safety notices in this section are provided in the following languages: v English v Arabic v Brazilian Portuguese v French v German v Hebrew v Japanese v Korean v Spanish v Traditional Chinese Safety information 7
DANGER Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts. DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it.
DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. DANGER Unless hot swap is allowed for the FRU being replaced, do as follows before removing it: power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and disconnect any interconnecting cables.
10 ThinkPad Edge 13″ and E30 Hardware Maintenance Manual
Safety information 11
PERIGO Antes de ligar o computador após a substituição da FRU, certifique-se de que todos os parafusos, molas e outras peças pequenas estejam no lugar e não estejam soltos dentro do computador. Verifique isso sacudindo o computador e procurando ouvir sons de peças soltas. Peças metálicas ou lascas de metal podem causar curto-circuito. PERIGO Algumas baterias reserva contêm uma pequena quantidade de níquel e cádmio.
PERIGO Embora as principais baterias possuam baixa voltagem, uma bateria em curto-circuito ou aterrada pode produzir corrente o bastante para queimar materiais de pessoal ou inflamáveis. PERIGO A menos que uma hot swap seja permitida para a FRU que está sendo substituída, faça o seguinte antes de removê-la: desligue o computador, desconecte todos os cabos de energia das tomadas, remova o pacote de baterias e desconecte quaisquer cabos de interconexão.
DANGER Avant de remettre l’ordinateur sous tension après remplacement d’une unité en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer un court-circuit. DANGER Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau.
DANGER Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d’une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves.
VORSICHT Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen. VORSICHT Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten.
VORSICHT Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den Boden fällt.
18 ThinkPad Edge 13″ and E30 Hardware Maintenance Manual
Safety information 19
20 ThinkPad Edge 13″ and E30 Hardware Maintenance Manual
Safety information 21
22 ThinkPad Edge 13″ and E30 Hardware Maintenance Manual
Safety information 23
PELIGRO Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos. PELIGRO Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio.
PELIGRO Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.
26 ThinkPad Edge 13″ and E30 Hardware Maintenance Manual
Safety information 27
28 ThinkPad Edge 13″ and E30 Hardware Maintenance Manual
Important service information This chapter presents following important service information that applies to all machine types supported by this manual: v “Strategy for replacing FRUs” on page 30 – “Strategy for replacing a hard disk drive” on page 30 – “Important notice for replacing a system board” on page 31 – “How to use error message” on page 31 v “Strategy for replacing FRUs for CTO, CMV, and GAV” on page 32 – “Product definition” on page 32 – “FRU identification for CTO, CMV, and GAV products” on page
Strategy for replacing FRUs Before replacing parts: Make sure that all software fixes, drivers, and BIOS downloads are installed before replacing any FRUs listed in this manual. After a system board is replaced, ensure that the latest BIOS is loaded to the system board before completing the service action. To download software fixes, drivers, and BIOS, do as follows: 1. Go to http://www.lenovo.com/support 2. Enter the product number of the computer or press Auto-detect button on the screen. 3.
Important notice for replacing a system board Some components mounted on a system board are very sensitive. Improper handling of a system board can cause damage to those components, and may cause a system malfunction. Attention: When handling a system board: v Do not drop a system board or apply any excessive force to it. v Avoid rough handling of any kind. v Avoid bending a system board and hard pushing to prevent cracking at each BGA (Ball Grid Array) chipset.
Strategy for replacing FRUs for CTO, CMV, and GAV Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure an IBM® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under SYSTEM DETAILS. v Authorized IBM Business Partners can access Eclaim at the following Web site: https://wca.eclaim.
34 ThinkPad Edge 13″ and E30 Hardware Maintenance Manual
General checkout This chapter presents following information: v “What to do first” on page 36 v “Checkout guide” on page 37 – “Diagnostics using PC-Doctor for DOS” on page 37 – “Lenovo ThinkVantage Toolbox (Lenovo System Toolbox)” on page 40 – “PC-Doctor for Rescue and Recovery” on page 40 – “FRU tests” on page 41 v “Power system checkout” on page 43 The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS diagnostics program.
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of service technician __ 2. Date of service __ 3. Date on which the machine failed __ 4. Date of purchase __ 5. Failure symptoms, error codes appearing on the display, and beep symptoms __ 6. Procedure index and page number in which the failing FRU was detected __ 7. Failing FRU name and part number __ 8.
Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad Notebook. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms.
Testing the computer In this product, you need an external optical drive to use the PC-Doctor diagnostic CD to test the hardware features. Note: The PC-Doctor diagnostic CD does not support any external optical drives connected through USB devices or any others. To run the test, do as follows: 1. Turn off the computer. 2. Attach an external optical drive through the USB connector to the computer. 3. Set the external optical drive as a startup device. 4. Turn off the computer. 5. Turn on the computer.
The options on the test menu are as follows: Diagnostics v v v v v v v v v v Run Normal Test Run Quick Test CPU/Coprocessor System board Video Adapter Fixed Disks Diskette Drives Other Devices Wireless LAN Advanced Memory Tests Interactive Tests v v v v v v v v Keyboard Video Internal Speaker Mouse Diskette System Load Optical Drive Test Intel WLAN Radio Test Note: v In the Keyboard test in Interactive Tests, the Fn key should be held down for at least 2 seconds; otherwise, it cannot be sensed.
v v v v Print Log Save Log Full Erase Hard Drive Quick Erase Hard Drive Lenovo ThinkVantage Toolbox (Lenovo System Toolbox) Lenovo ThinkVantage® Toolbox is a diagnostic program that works through the Windows operating system. It enables you to view symptoms of computer problems and solutions for them, and includes automatic notification when action is required, computing assistance, advanced diagnostics, and diagnostic history.
FRU tests The following table shows the test for each FRU. Table 1. FRU tests FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard Power Diagnostics --> ThinkPad Devices --> AC Adapter, Battery 1 (Battery2) LCD unit 1. Diagnostics --> Video Adapter 2.
Table 1. FRU tests (continued) 42 FRU Applicable test Touch Pad If the Touch Pad does not work, check the configuration as specified in the BIOS Setup Utility. If the Touch Pad is disabled, select Automatic to enable it.
Power system checkout To 1. 2. 3. 4. 5. 6. 7. verify a symptom, do the following: Turn off the computer. Remove the battery pack. Connect the AC adapter. Check that power is supplied when you turn on the computer. Turn off the computer. Disconnect the AC adapter and install the charged battery pack. Check that the battery pack supplies power when you turn on the computer.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack.
4. If the voltage is more than +11.0 V dc, measure the resistance between battery terminals 5 and 7. The resistance must be 4 to 30 K . If the resistance is not correct, replace the battery pack. If the resistance is correct, replace the system board. Checking the backup battery Do the following: 1. Power off the computer, and unplug the AC adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 68). 4.
46 ThinkPad Edge 13″ and E30 Hardware Maintenance Manual
Related service information This chapter presents following information: v “Restoring the factory contents by using Recovery Disc Set” v “Passwords” on page 48 v “Power management” on page 52 v “Symptom-to-FRU index” on page 53 Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.
Note: Recovery takes several hours. The length of time depends on the method you use. If you use recovery discs, recovery takes at least five hours. 1. Make the CD/DVD drive the first startup device in the startup sequence using the following procedure: a. Press and hold down the F1 key, and then turn on the computer. When the logo screen is displayed or if you hear repeating beeps, release the F1 key. The Setup Utility program opens. b. Use the arrow keys to select Startup → Boot. 2. 3. 4. 5. 6. 7. 8. 9.
Exception: If only an SVP is installed, the password prompt does not appear when the operating system is booted. Power-on password A power-on password (POP) protects the system from being powered on by an unauthorized person. The password must be entered before an operating system can be booted. For how to remove the POP, see “How to remove the power-on password.
After the POST ends, the password prompt does not appear. The POP has been removed. 5. Reinstall the backup battery and the battery pack. (B) If an SVP has been set and is known by the service technician: 1. Turn on the computer. 2. When the ThinkPad logo comes up, immediately press F1 to enter BIOS Setup Utility. For models supporting the Passphrase function, press F1 while the POP icon is appearing on the screen; then enter the POP. For the other models, enter the POP.
7. Type the current master HDP in the Enter Current Password field. then leave the Enter New Password field blank, and press Enter twice. 8. Press F10. 9. Select Yes in the Setup Configuration window. Both user HDP and master HDP will have been removed.
Power management To reduce power consumption, the computer has three power management modes: screen blank, sleep, and hibernation. Screen blank mode To put the computer into screen blank mode, do as follows: 1. Right-click the Power Manager Battery Gauge in the task bar. 2. Select Power off display. Sleep mode When the computer enters sleep mode, the following events occur in addition to what occurs in screen blank mode: v The LCD is powered off. v The hard disk drive is powered off. v The CPU stops.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 56 v “No-beep symptoms” on page 56 v “LCD-related symptoms” on page 57 v “Intermittent problems” on page 58 v “Undetermined problems” on page 58 The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type.
Table 2. Numeric error codes (continued) 54 Symptom or error (beeps, if any) FRU or action, in sequence 0211 Keyboard error (two short beeps) Run interactive tests of the keyboard and the auxiliary input device. 0230 Shadow RAM error—Shadow RAM fails at offset nnnn. (two short beeps) System board. 0231 System RAM error—System RAM fails at offset nnnn. (two short beeps) 1. DIMM. 2. System board. 0232 Extended RAM error— Extended RAM fails at offset nnnn. (two short beeps) 1. DIMM. 2. System board.
Table 2. Numeric error codes (continued) Symptom or error (beeps, if any) FRU or action, in sequence 02F0 CPU ID:xx Failed. 1. CPU. 2. System board. 02F5 DMA test failed. (two short beeps) 1. DIMM. 2. System board. 02F6 Software NMI failed (two short beeps) 1. DIMM. 2. System board. 02F7 Fail-safe timer NMI failed (two short beeps) 1. DIMM. 2. System board. 1802 Unauthorized network card is plugged in—Turn off and remove the miniPCI network card. (two short beeps) 1.
Error messages Table 3. Error messages Symptom or error (beeps, if any) FRU or action, in sequence Bad CRC2. Enter BIOS Setup Utility, and load Setup defaults. (two short beeps) Press F1 to enter BIOS Setup Utility. Press F9, and Enter to load the default setting. Then save the current setting by pressing F10, and restart the computer. Fan error. (four short beeps, one long beep) 1. Fan. 2. Thermal grease. 3. System board. DRAM is unplugged.
LCD-related symptoms Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3.
Status indicators This chapter presents the system status indicators that show the status of the computer. 1 2 3 4 Table 6. Status indicators Indicator Meaning 1 Caps lock: On-screen indicators Caps Lock mode is enabled. You can enter all alphabetic characters (A-Z) in uppercase without pressing the Shift key. Wireless status: Press F9 to enable or disable the wireless features. You can quickly change the power state of each feature in the list.
Table 6. Status indicators (continued) 60 Indicator Meaning 3 Sleep (standby) status 4 Sleep (standby) status The illumination dot in the ThinkPad logo on the outer lid of the computer and on the palm rest works as a system-status indicator: it shows whether the computer is in sleep (standby), hibernation, or normal model. Red: The computer is on (in normal mode). Fast blinking red: The computer is entering sleep (standby) or hibernation mode.
Special keys This computer has several special keys at the upper row of the keyboard. To use each function, directly press the desired key. Note: To use F1 - F12 functions, press Fn and the desired function key simultaneously; this is the default setting. The following table shows the function of each special key. Table 7. Fn key combinations Special key Description Speaker mute (F1) If you mute the sound and then turn off the computer, the sound will remain muted when you turn on the computer again.
Table 7. Fn key combinations (continued) Special key Description Wireless radio control (F9) Enable or disable the built-in wireless networking features. If you press this key, a list of wireless features is displayed. You can quickly change the power state of each feature in the list.
FRU replacement notices This chapter presents notices related to removing and replacing parts. Read this chapter carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad Notebook, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten. v Each one should be used only once.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information” on page 65 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.
The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same number. When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.
66 ThinkPad Edge 13″ and E30 Hardware Maintenance Manual
Removing and replacing a FRU This chapter presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 63. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any such FRUs are listed at the top of the page.
1010 Battery pack Important notice for replacing a battery pack: ThinkVantage Toolbox has an automatic battery diagnostic that determines if the battery pack is defective. A battery pack FRU should not be replaced unless this diagnostic shows that the battery is defective. The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue.
Table 8. Removal steps of battery pack (continued) Unlock the battery latch 1 . Holding the battery latch in the unlocked position 2 , remove the battery pack in the direction shown by arrow 3 . 1 2 3 When installing: Install the battery pack in the slot, and then make sure that the battery latch is in the locked position.
1020 Bottom slot cover For access, remove this FRU: v “1010 Battery pack” on page 68 Table 9. Removal steps of bottom slot cover Note: Loosen the screws 1 , but do not remove them. 1 1 1 2 1 1 When installing: Make sure that all the projections of the cover are attached firmly to the frame. Then secure the screws.
Note: Applying label to the bottom slot cover When you replace the cover, following label needs to be peeled off from the old cover, and needs to be put on the new cover: 1 Asset tag label For the label location, refer the following figure: 1 Removing and replacing a FRU 71
1030 DIMM For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 Table 10. Removal steps of DIMM 1 2 1 a b Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ). When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.
1040 Hard disk drive (HDD) For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 Attention: v Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible. v Never remove the drive while the system is operating or is in suspend mode. Table 11.
Table 11. Removal steps of HDD (continued) 2 3 When installing: Make sure that the HDD connector is attached firmly.
1050 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 Table 12. Removal steps of PCI Express Mini Card for wireless LAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. 2 2 1 Step Screw (quantity) Color Torque 2 M2 × 3 mm, wafer-head, nylon-coated (2) Black 0.
Table 12. Removal steps of PCI Express Mini Card for wireless LAN (continued) 3 When installing: Plug the gray cable into the jack marked MAIN or M, and the black cable into the jack marked AUX or A on the card.
1060 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 Table 13. Removal steps of PCI Express Mini Card for wireless WAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. 2 2 1 Step Screw (quantity) Color Torque 2 M2 × 3 mm, wafer-head, nylon-coated (2) Black 0.
Table 13. Removal steps of PCI Express Mini Card for wireless WAN (continued) 3 Note: Plug the red cable into the jack marked MAIN, and the blue cable into the jack marked AUX on the card.
1070 Keyboard For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 Table 14. Removal steps of keyboard 1 1 Step Screw (quantity) Color Torque 1 M2 × 5 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) In step 2 , by using a plastic pry tool, push the keyboard out from two square holes in the battery pack slot as shown in this figure.
Table 14.
Table 15. Installation steps of keyboard When installing the keyboard, do as follows: 1. Attach the keyboard connectors. 2. Attach the keyboard so that the keyboard front edges are under the frame as shown in this figure. 3. Secure the keyboard by tightening the screws from the bottom side of the computer.
1080 Top case assembly and microphone module For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 v “1040 Hard disk drive (HDD)” on page 73 v “1070 Keyboard” on page 79 Note: Microphone module is attached on the underside of the top case assembly. Table 16. Removal steps of top case assembly and microphone module 1 1 1 1 1 1 1 1 1 82 1 Step Screw (quantity) Color Torque 1 M2 × 5 mm, wafer-head, nylon-coated (10) Black 0.181 Nm (1.
Table 16. Removal steps of top case assembly and microphone module (continued) 2 2 2 2 2 2 Step Screw (quantity) Color Torque 2 M2 × 3 mm, wafer-head, nylon-coated (6) Black 0.181 Nm (1.85 kgfcm) 3 3 3 Step Screw (quantity) Color Torque 3 M2 × 3 mm, wafer-head, nylon-coated (3) Black 0.181 Nm (1.
Table 16. Removal steps of top case assembly and microphone module (continued) 4 5 6 7 8 When installing: Make sure that the connectors are attached firmly.
Table 16. Removal steps of top case assembly and microphone module (continued) In step 5 , push the top case assembly out from the frame by using a plastic pry tool as shown in this figure.
1090 Backup battery For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 v “1070 Keyboard” on page 79 v “1080 Top case assembly and microphone module” on page 82 Table 17. Removal steps of backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. 1 2 When installing: Make sure that the connector is attached firmly.
1100 Bluetooth daughter card (BDC-2) v v v v “1010 “1020 “1070 “1080 Battery pack” on page 68 Bottom slot cover” on page 70 Keyboard” on page 79 Top case assembly and microphone module” on page 82 Table 18. Removal steps of BDC-2 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector is attached firmly.
1110 Speaker assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 v “1070 Keyboard” on page 79 v “1080 Top case assembly and microphone module” on page 82 Table 19. Removal steps of speaker assembly 1 1 1 1 88 Step Screw (quantity) Color Torque 2 M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.
Table 19. Removal steps of speaker assembly (continued) 2 3 3 Cable routing: Make sure that the connector is attached firmly and you route the cable as shown in this figure.
1120 System board and fan assembly Important notices for handling the system board: When handling the system board, bear the following in mind. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces. Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock.
Table 20. Removal steps of system board and fan assembly Following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling.
Table 20.
Table 20. Removal steps of system board and fan assembly (continued) 2 2 1 1 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (3) Black 0.181 Nm (1.85 kgfcm) Note: Loosen the screws 2 , but do not remove them.
Table 20. Removal steps of system board and fan assembly (continued) 3 4 When installing: Make sure that the connectors are attached firmly.
Table 20. Removal steps of system board and fan assembly (continued) a 5 8 7 6 When installing: Attach the system board so that the battery pins of the system board are attached firmly to the guide hole of the base cover as shown in a in this figure. Make sure that the connectors are attached firmly.
Table 20. Removal steps of system board and fan assembly (continued) Note: Loosen the screws 9 , but do not remove them.
Table 20. Removal steps of system board and fan assembly (continued) When installing: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. You need to peel the thin film off from the rubbers b .
1130 I/O card assembly, audio cable, and I/O cable For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 v “1040 Hard disk drive (HDD)” on page 73 v “1050 PCI Express Mini Card for wireless LAN” on page 75 v “1060 PCI Express Mini Card for wireless WAN” on page 77 v “1070 Keyboard” on page 79 v “1080 Top case assembly and microphone module” on page 82 v “1110 Speaker assembly” on page 88 v “1120 System board and fan assembly” on page 90 Table 21.
Table 21. Removal steps of I/O card assembly, audio cable, and I/O cable (continued) 6 5 Cable routing: Make sure that the connectors are attached firmly and you route the cables as shown in this figure.
1140 LCD unit For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 v “1040 Hard disk drive (HDD)” on page 73 v “1050 PCI Express Mini Card for wireless LAN” on page 75 v “1060 PCI Express Mini Card for wireless WAN” on page 77 v “1070 Keyboard” on page 79 v “1080 Top case assembly and microphone module” on page 82 v “1110 Speaker assembly” on page 88 v “1120 System board and fan assembly” on page 90 Table 22.
Table 22. Removal steps of LCD unit (continued) 3 3 Cable routing: Make sure that the cables are attached to the cable guides as shown in this figure. When you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
1150 Base cover assembly and DC-in cable For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 v “1040 Hard disk drive (HDD)” on page 73 v “1050 PCI Express Mini Card for wireless LAN” on page 75 v “1060 PCI Express Mini Card for wireless WAN” on page 77 v “1070 Keyboard” on page 79 v “1080 Top case assembly and microphone module” on page 82 v “1110 Speaker assembly” on page 88 v “1120 System board and fan assembly” on page 90 v “1140 LCD unit” on pag
Table 23. Removal steps of base cover assembly and DC-in cable (continued) Cable routing: Make sure that the cable is attached to the cable guides as shown in this figure. When you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: 4 Information label under battery 6 FCC label 7 Homologation label 13 Serial number blank label Following labels need to be peeled off from the old base cover, and need to be put on the new base cover.
2010 LCD bezel assembly For access, remove this FRU: v “1010 Battery pack” on page 68 Table 24. Removal steps of LCD bezel assembly 1 1 1 1 Step 1 Screw cap Screw (quantity) M2 × 3 mm, wafer-head, nylon-coated (4) 2 Color Torque Black 0.181 Nm (1.
2020 Integrated camera For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “2010 LCD bezel assembly” on page 105 Table 25. Removal steps of integrated camera 1 2 When installing: Make sure that the connector of the integrated camera is attached firmly.
2030 LCD panel and LCD cable For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 v “1040 Hard disk drive (HDD)” on page 73 v “1050 PCI Express Mini Card for wireless LAN” on page 75 v “1060 PCI Express Mini Card for wireless WAN” on page 77 v “1070 Keyboard” on page 79 v “1080 Top case assembly and microphone module” on page 82 v “1110 Speaker assembly” on page 88 v “1120 System board and fan assembly” on page 90 v “1140 LCD unit” on page 100 Table
Table 26.
Table 26.
2070 Hinge kit For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 v “1040 Hard disk drive (HDD)” on page 73 v “1050 PCI Express Mini Card for wireless LAN” on page 75 v “1060 PCI Express Mini Card for wireless WAN” on page 77 v “1070 Keyboard” on page 79 v “1080 Top case assembly and microphone module” on page 82 v “1110 Speaker assembly” on page 88 v “1120 System board and fan assembly” on page 90 v “1140 LCD unit” on page 100 v “2030 LCD panel an
Table 27.
2050 Wireless LAN antenna assembly, wireless WAN antenna assembly, and LCD rear cover assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 68 v “1020 Bottom slot cover” on page 70 v “1040 Hard disk drive (HDD)” on page 73 v “1050 PCI Express Mini Card for wireless LAN” on page 75 v “1060 PCI Express Mini Card for wireless WAN” on page 77 v “1070 Keyboard” on page 79 v “1080 Top case assembly and microphone module” on page 82 v “1110 Speaker assembly” on page 88 v “1120 System board
Table 28. Removal steps of wireless LAN antenna assembly, wireless WAN antenna assembly, and LCD rear cover assembly (continued) 3 3 3 3 3 3 Cable routing: When you install the antenna assembly, route the cables as shown in the figures below. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
114 ThinkPad Edge 13″ and E30 Hardware Maintenance Manual
Locations This chapter presents the location of ThinkPad Edge 13″ features and hardware. Front view 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Integrated camera (for some models) Power switch AC power connector Status indicators Note: For the description of each indicator, see “Status indicators” on page 59. Universal serial bus (USB) connectors Combo audio jack Media Card Reader slot Status indicators Note: For the description of each indicator, see “Status indicators” on page 59.
Bottom view 1 2 3 4 5 6 7 8 9 Battery pack latch Battery pack Security keyhole External monitor connector HDMI port RJ-45 (Ethernet) connector USB connector Built-in stereo speakers HDD slot door 1 2 1 3 9 4 5 8 116 ThinkPad Edge 13″ and E30 Hardware Maintenance Manual 6 7
Parts list This chapter contains following lists of the service parts. v “Overall” on page 118 v “LCD FRUs” on page 126 v “Keyboard” on page 129 v “AC adapters” on page 130 v “Miscellaneous parts” on page 130 v “Power cords” on page 131 v “Recovery discs” on page 132 v “Common service tools” on page 136 Notes: v Each FRU is available for all types or models, unless specific types or models are specified.
Overall 1 21 2 3 20 4 19 5 18 6 7 17 16 8 9 10 15 11 14 12 13 118 ThinkPad Edge 13″ and E30 Hardware Maintenance Manual
Table 29. Parts list—Overall No. FRU (Overall) FRU no. CRU ID 1 LCD unit (see “LCD FRUs” on page 126.) 2 Keyboard (see “Keyboard” on page 129.
Table 29. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 29. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 29. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 29. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 29. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 29. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 18 System board assembly, AMD Athlon Neo X2 Single-Core MV-40 v 0197-CTO 60Y5707 N 19 60Y3199 Bluetooth daughter card (BDC-2.
LCD FRUs 1 2 8 7 3 4 6 5 126 ThinkPad Edge 13″ and E30 Hardware Maintenance Manual
Table 30. Parts list—13.3-inch HD LED-backlight LCD No. FRU (13.3-inch HD LED-backlight LCD) FRU no.
Table 30. Parts list—13.3-inch HD LED-backlight LCD (continued) No. FRU (13.3-inch HD LED-backlight LCD) FRU no.
Keyboard Table 31. Parts list—Keyboard Language FRU no. CRU ID Arabic 60Y9513 60Y9443 Belgian 60Y9514 60Y9444 Brazilian Portuguese 60Y9512 60Y9442 Bulgarian 60Y9515 60Y9445 Canadian French (058) 60Y9510 60Y9440 Canadian French (Acnor) 60Y9509 60Y9439 Czech 60Y9516 60Y9446 Danish 60Y9517 60Y9447 Dutch 60Y9527 60Y9457 Finnish, Swedish 60Y9534 60Y9464 French 60Y9519 60Y9449 German 60Y9520 60Y9450 Greek (U.S.
AC adapters Table 32. Parts list—2-pin AC adapters FRU FRU no. CRU ID 2-pin (65 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY) 42T5282 * 2-pin (65 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY) 42T4423 2-pin (65 W, 20 V) adapter (models CTO, xxE, xxF, xxJ, xxL, xxP, xxS, xxU, xxY) 42T4419 Table 33. Parts list—3-pin AC adapters FRU FRU no.
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 35. Parts list—2-pin power cords Country or region FRU no. CRU ID Argentina v models -CTO, xxY 42T5020 42T5105 * Brazil v models -CTO, xxP 42T5180 42T5183 Canada, U.S. v models -CTO, xxF, xxL, xxS, xxU 42T5008 42T5093 Japan v models -CTO, xxE, xxJ 42T5014 42T5099 Table 36. Parts list—3-pin power cords Country or region FRU no.
Recovery discs Windows 7 Home Basic (32 bit) DVDs Windows 7 Home Basic (32 bit) is preinstalled as the operating system in the following models: v 0196-CTO, 2Zx, 3Hx, 4Fx, 4Gx, 4Jx, 4Lx, 4Nx, 4Px v 0197-CTO, 2Jx, 2Rx, 2Vx, 2Zx, 39x, 3Tx, 3Ux, 3Vx, 3Wx, 3Yx, 3Zx, 42x, 43x, 45x, 46x, 47x, 48x, 4Ax, 4Bx, 4Cx, 4Dx, 4Fx, 4Gx, 4Hx, 4Jx, 4Lx, 4Mx, 4Nx, 4Px v 0492-CTO, 2Fx, 2Gx, 2Hx, 2Kx, 2Lx, 2Nx, 2Px, 2Qx, 2Tx, 32x, 33x, 35x, 36x, 37x, 39x, 3Ax, 3Bx, 3Cx Table 37.
Windows 7 Home Premium (64 bit) DVDs Windows 7 Home Premium (64 bit) is preinstalled as the operating system in the following models: v 0196-CTO, 2Ux, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 4Cx v 0197-CTO, 25x, 27x, 29x, 2Ax, 2Cx, 2Dx, 2Mx, 2Px, 4Xx, 4Zx, 53x, 55x, 57x, 59x, 5Bx, 5Dx, 5Fx, 5Hx, 5Kx, 5Mx, 5Px, 5Rx, 5Tx, 5Vx, 6Lx, 6Mx, 6Nx, 6Px v 0492-CTO, 2Ax, 2Bx, 2Cx, 2Yx Table 39.
Windows 7 Professional (32 bit) DVDs Windows 7 Professional (32 bit) is preinstalled as the operating system in the following models: v 0196-CTO, 24x, 29x, 2Cx, 2Ex, 2Fx, 2Hx, 2Jx, 2Xx, 35x, 36x, 3Bx, 3Ex, 3Fx, 3Gx, 3Jx, 3Kx, 3Px, 3Yx, 3Zx, 42x, 44x, 45x, 46x v 0197-CTO, 28x, 2Hx, 2Kx, 2Lx, 33x, 3Ax, 3Cx, 3Dx, 3Fx, 3Gx, 3Jx, 3Lx, 4Rx, 4Tx, 4Vx, 4Yx, 52x, 54x, 56x, 58x, 5Ax, 5Cx, 5Ex, 5Gx, 5Jx, 5Lx, 5Nx, 5Qx, 5Sx, 5Ux, 5Wx, 5Xx, 5Yx, 5Zx, 6Ex, 6Gx, 6Hx, 6Sx, 6Tx, 6Ux, 6Vx, 6Wx, 6Xx, 6Zx, 72x, 73x v 0492-CTO,
Windows 7 Professional (64 bit) DVDs Windows 7 Professional (64 bit) is preinstalled as the operating system in the following models: v 0196-CTO, 22x, 23x, 25x, 26x, 27x, 28x, 2Ax, 2Bx, 2Dx, 2Gx, 2Kx, 2Vx, 2Wx, 37x, 38x, 39x, 3Ax, 47x v 0197-CTO, 23x, 24x, 26x, 2Ex, 2Fx, 2Qx, 2Wx, 3Px, 3Qx, 3Sx, 4Sx, 4Ux, 4Wx, 6Qx, 6Rx, 6Yx v 0492-CTO, 23x, 25x, 2Dx, 2Ex Table 41.
Common service tools Table 42. Parts list—Common service tools Tool P/N Screwdriver kit 95F3598 1/4″ drive spinner handle 1650840 1/4″ Sq. to 1/4″ hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Part Number: 63Y0744 (1P) P/N: 63Y0744
