User Guide ThinkPad X220, X220i, X220 Tablet, and X220i Tablet
Notes: Before using this information and the product it supports, be sure to read the following: • Safety and Warranty Guide • Regulatory Notice • “Important safety information” on page vi • Appendix C “Notices” on page 251 The Safety and Warranty Guide and the Regulatory Notice have been uploaded on the Web site. To refer to them, go to http://www.lenovo.com/support, and then click User Guides & Manuals. First Edition (April 2011) © Copyright Lenovo 2011.
Contents Read this first . . . . . . . . . . . . . . v Important safety information . . . . . . . . . . vi Conditions that require immediate action . . vii Safety guidelines . . . . . . . . . . . . vii Chapter 1. Product Overview . . . . . . 1 Locating computer controls, connectors, and indicators. . . . . . . . . . . . . . . . Front view. . . . . . . . . . . . . . Right-side view. . . . . . . . . . . . Left-side view . . . . . . . . . . . . Bottom view . . . . . . . . . . . . . Rear view . . . . . . . . .
Ergonomic information. . . . . Adjusting your computer to fit you Accessibility information . . . . FullScreen Magnifier function . . Traveling with your computer . . . . Travel tips . . . . . . . . . . Travel accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 84 85 85 86 86 86 Chapter 4. Security . . . . . . . . . . 89 Attaching a mechanical lock . . . . . . . . . Using passwords. . . . . . . . . . . . . . Passwords and sleep (standby) mode . . . .
Config menu. . . . . . . . . Date and time menu. . . . . . Security menu . . . . . . . . Startup menu . . . . . . . . Restart menu . . . . . . . . ThinkPad Setup items . . . . . Updating your system UEFI BIOS Using system management. . . . . System management . . . . . Setting management features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 9. Preventing problems . . General tips for preventing problems . . . . .
iv User Guide
Read this first Be sure to follow the important tips given here to continue to get the most use and enjoyment out of your computer. Failure to do so might lead to discomfort or injury, or cause your computer to fail. When your computer is turned on or the battery is charging, the base, the palm rest, and some other parts may become hot. The temperature they reach depends on the amount of system activity and the level of charge in the battery.
Protect your computer and data when moving it. Before moving a computer equipped with a hard disk drive, do one of the following, and make sure that the power switch is off or is blinking: • Turn it off. • Press Fn+F4 to put it in sleep (standby) mode. • Press Fn+F12 to put it in hibernation mode. This will help to prevent damage to the computer, and possible loss of data. Handle your computer gently.
Conditions that require immediate action Products can become damaged due to misuse or neglect. Some product damage is serious enough that the product should not be used again until it has been inspected and, if necessary, repaired by an authorized servicer. As with any electronic device, pay close attention to the product when it is turned on. On very rare occasions, you might notice an odor or see a puff of smoke or sparks vent from your product. Or you might hear sounds like popping, cracking or hissing.
Replaceable Units, or CRUs. Lenovo provides documentation with instructions when it is appropriate for customers to install options or replace CRUs. You must closely follow all instructions when installing or replacing parts. The Off state of a power indicator does not necessarily mean that voltage levels inside a product are zero. Before you remove the covers from a product equipped with a power cord, always make sure that the power is turned off and that the product is unplugged from any power source.
Power cords and power adapters DANGER Use only the power cords and power adapters supplied by the product manufacturer. The power cords shall be safety approved. For Germany, it shall be H05VV-F, 3G, 0.75 mm2, or better. For other countries, the suitable types shall be used accordingly. Never wrap a power cord around a power adapter or other object. Doing so can stress the cord in ways that can cause the cord to fray, crack, or crimp. This can present a safety hazard.
Plugs and outlets DANGER If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged or corroded, do not use the outlet until it is replaced by a qualified electrician. Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement.
Batteries DANGER Personal computers manufactured by Lenovo contain a coin cell battery to provide power to the system clock. In addition, many mobile products, such as notebook computers, utilize a rechargeable battery pack to provide system power when in portable mode. Batteries supplied by Lenovo for use with your product have been tested for compatibility and should only be replaced with approved parts. Never attempt to open or service any battery.
Lithium coin cell battery notice DANGER Danger of explosion if battery is incorrectly replaced. When replacing the lithium coin cell battery, use only the same or an equivalent type that is recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: • Throw or immerse into water • Heat to more than 100°C (212°F) • Repair or disassemble Dispose of the battery as required by local ordinances or regulations.
Heat and product ventilation DANGER Computers, ac power adapters, and many accessories can generate heat when turned on and when batteries are charging. notebook computers can generate a significant amount of heat due to their compact size. Always follow these basic precautions: • When your computer is turned on or the battery is charging, the base, the palm rest, and some other parts may become hot.
Electrical current safety information DANGER Electric current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: • Do not use your computer during a lightning storm. • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. • Connect all power cords to a properly wired and grounded electrical outlet. • Connect to properly wired outlets any equipment that will be attached to this product.
the equalizer to maximum increases the earphones and headphones output voltage and therefore the sound pressure level. Excessive use of headphones or earphones for a long period of time at high volume can be dangerous if the output of the headphone or earphone connectors do not comply with specifications of EN 50332-2. The headphone output connector of your computer complies with EN 50332-2 Sub clause 7. This specification limits the computer’s maximum wide band true RMS output voltage to 150 mV.
xvi User Guide
Chapter 1. Product Overview This chapter provides information about the locations of connectors, locating important product information, computer features, specifications, operating environment, and preinstalled software programs.
ThinkPad X220 and X220i front view Figure 1.
2 Integrated camera Some models have the integrated camera. By using this camera, you can take pictures or hold a video conference. For more information about how to use the camera, refer to “Using an integrated camera” on page 78. 3 ThinkLight You can use your computer under less than perfect lighting conditions. To illuminate the keyboard, turn on the ThinkLight® by pressing Fn+PgUp. To turn it off, press Fn+PgUp again.
11 TrackPoint buttons 12 Touch pad 13 TrackPoint pointing stick The keyboard contains the unique TrackPoint® pointing device. Pointing, selecting, and dragging are all part of a single process that you can perform without moving your fingers from typing position. Move your fingertip across the UltraNav® touch pad to move the pointer. The TrackPoint and TrackPoint buttons provide functions similar to those of a mouse and its buttons.
ThinkPad X220 Tablet and X220i Tablet front view Figure 2.
1 Wireless WAN (auxiliary) and Wireless LAN/WiMAX (auxiliary) 4 Wireless LAN (third), Wireless WAN (main), and Wireless LAN/WiMAX (main) The built-in antennas for the wireless communication are located at the top left and the top right portions of your computer display. For the specific locations of each antenna, refer to “Location of the UltraConnect wireless antennas” on page 244. 2 Integrated camera Some models have the integrated camera.
10 PCI Express Mini Card slot for wireless WAN or mSATA solid state drive (SSD) Your computer might include a PCI Express Mini Card in the PCI Express Mini Card slot which enables wireless WAN communications. With Lenovo technologies advancing to provide you with the best engineered systems, some models are equipped with an mSATA solid state drive for data storage. This cutting-edge technology enables notebook computers to be lighter, smaller and faster.
Right-side view This section provides right-side view for your computer. ThinkPad X220 and X220i right-side view Figure 3. Right-side view 1 1 Security keyhole 2 Hard disk drive or solid state drive 3 Combo audio jack 4 Ethernet connector 5 Always On USB connector 6 Media card reader slot Security keyhole Your computer comes with a security keyhole. You can purchase a security cable and lock to fit this keyhole.
Notes: • If you are using a headset with a function switch, for example, a headset for an iPhone® mobile digital device, do not press this switch while using the headset. If you press it, the headset microphone will be disabled, and the internal microphone will be enabled instead. • The combo audio jack does not support a conventional microphone. For more information about the audio devices supported by the combo audio jack of your compute, see “Using audio features” on page 77.
For details, refer to the instructions in “Using an ExpressCard, a smart card, or a flash media card” on page 79. ThinkPad X220 Tablet and X220i Tablet right-side view Figure 4. Right-side view 1 Security keyhole 2 Tablet Digitizer Pen 3 Hard disk drive or solid state drive 4 Combo audio jack 5 Ethernet connector 6 Always On USB connector 7 Media card reader slot 1 Security keyhole Your computer comes with a security keyhole. You can purchase a security cable and lock to fit this keyhole.
4 Combo audio jack To listen to the sound from your computer, connect a headphone or a headset, that has a 3.5mm 4-pole plug, to the combo audio jack. Notes: • If you are using a headset with a function switch, for example, a headset for an iPhone mobile digital device, do not press this switch while using the headset. If you press it, the headset microphone will be disabled, and the internal microphone will be enabled instead. • The combo audio jack does not support a conventional microphone.
Note: Your computer does not support the CPRM feature for SD card. For details, refer to the instructions in “Using an ExpressCard, a smart card, or a flash media card” on page 79. Left-side view This section provides left-side view for your computer. ThinkPad X220 and X220i left-side view Figure 5.
Note: Your computer is compatible with USB 1.1 and 2.0. When you attach a USB cable to the connector, make sure that the mark is to the upper side. Otherwise the connector might be damaged. 4 DisplayPort connector Your computer supports the DisplayPort, a next-generation digital display interface that connects a compatible projector, external monitor, or HDTV to your computer. 5 Monitor connector You can attach an external monitor or a projector to your computer to display computer information.
ThinkPad X220 Tablet and X220i Tablet left-side view Figure 6. Left-side view 1 ExpressCard slot 2 Wireless radio switch 3 USB connectors (left) 4 DisplayPort connector 5 Monitor connector 6 USB connector 7 Fan louvers (left) 1 ExpressCard slot Your computer has an ExpressCard slot for a 54 mm-wide card. For details, refer to the instructions in “Using an ExpressCard, a smart card, or a flash media Card” on page 79.
5 Monitor connector You can attach an external monitor or a projector to your computer to display computer information. Note: If you attach your computer to the ThinkPad Ultrabase Series 3 and use a monitor connector, use the monitor connector on the ThinkPad Ultrabase Series 3, not the one on the computer. For details, refer to the instructions in “Attaching an external monitor” on page 71.
1 Battery Use your computer with battery power whenever ac power is unavailable. For details, refer to the instructions in “Power Manager” on page 36. 2 SIM card slot If your computer has a wireless WAN feature, it may require a SIM (Subscriber Identification Module) card to establish a wireless WAN (Wide Area Network) connections. Depending on the country of delivery, the SIM card may be already installed in the SIM card slot.
For details, refer to the instructions in “Power Manager” on page 36. 2 SIM card slot If your computer has a wireless WAN feature, it may require a SIM (Subscriber Identification Module) card to establish a wireless WAN (Wide Area Network) connections. Depending on the country of delivery, the SIM card may be already installed in the SIM card slot. 3 Docking connector With a ThinkPad Ultrabase Series 3, you can extend the computer capabilities when you are in your office or at home.
ThinkPad X220 Tablet and X220i Tablet rear view Figure 10. ThinkPad X220 Tablet and X220i Tablet rear view 1 Power jack 1 2 Fan louvers (rear) Power jack The ac power adapter cable connects to the computer power jack to provide power to the computer and charge the battery. 2 Fan louvers (rear) The internal fan and louvers enable air to circulate in the computer and cool the central processor. Note: To avoid impeding airflow, do not place any obstacle in front of the fan.
Status indicators 1 Device Access A hard disk drive or an optional drive, such as a drive in the Ultrabay, is being used to read or write data. When this indicator is blinking, do not put the computer into sleep (standby) mode, remove the device from the bay, or turn off the computer. 2 Bluetooth status • Green: The feature is on, and the radio link is ready for use, or the data is being transmitted. • Off: The Bluetooth feature is disabled.
8 Numeric lock By default, when the numeric lock is on, the numeric lock indicator is displayed on the screen. To change the settings of the numeric lock indicator, see “Changing display settings” on page 70. Note: Another mode available for your computer, though there is no indicator for it, is Scroll Lock mode. When this mode is enabled, the arrow keys can be used as function keys for screen-scrolling, but not for moving the cursor. To enable or disable this mode, press ScrLk.
• The battery status indicator is off: The battery is fully charged or the battery is detached. ThinkPad X220 Tablet and X220i Tablet status indicators Your computer has system-status indicators and power-status indicators. The status indicators show the current status of your computer. Status indicators 1 Power On The power switch stays lit whenever the computer is on, blinks when the computer is in sleep (standby) mode, and is off when the computer is off.
7 Device Access A hard disk drive or an optional drive, such as a drive in the Ultrabay, is being used to read or write data. When this indicator is blinking, do not put the computer into sleep (standby) mode, remove the device from the bay, or turn off the computer. 8 Numeric lock By default, when the numeric lock is on, the numeric lock indicator is displayed on the screen. To change the settings of the numeric lock indicator, see “Changing display settings” on page 70.
Note: If the computer is operating on battery power, the battery status indicator does not work while the computer is turned off or is in sleep (standby) mode or hibernation mode. • Quick blinking orange: An error occurred in the battery. • The battery status indicator blinks three times: The ac power adapter is attached to the computer. • The battery status indicator is off: The battery is fully charged or the battery is detached.
ThinkPad X220 Tablet and X220i Tablet FCC ID and IC Certification number label This section provides FCC ID and IC Certification number label location for your computer.
ThinkPad X220 and X220i FCC ID and IC Certification number label There is no FCC ID or IC Certification number for the PCI Express Mini Card shown on the enclosure of your computer. The FCC ID and IC Certification number label is affixed on the card installed in the PCI Express Mini Card slot of your computer. If no integrated wireless PCI Express Mini Card has been preinstalled in your computer, you can install one.
ThinkPad X220 Tablet and X220i Tablet FCC ID and IC Certification number label There is no FCC ID or IC Certification number for the PCI Express Mini Card shown on the enclosure of your computer. The FCC ID and IC Certification number label is affixed on the card installed in the PCI Express Mini Card slot of your computer. If no integrated wireless PCI Express Mini Card has been preinstalled in your computer, you can install one.
ThinkPad X220 and X220i ThinkPad X220 Tablet and X220i Tablet Features This section provides features for your notebook computer. ThinkPad X220 and X220i features Processor • See the system properties of your computer. You can do this as follows: Click Start, right-click Computer (in Windows XP, My Computer); then from the pull down menu select Properties. Memory • Double data rate 3 (DDR3) synchronous dynamic random access memory Storage device • 2.5-inch (76 mm) solid state drive or 2.
Display The color display uses TFT technology: • Size: 12.5 inch (317.
ThinkPad X220 Tablet and X220i Tablet features Processor • See the system properties of your computer. You can do this as follows: Click Start, right-click Computer (in Windows XP, My Computer); then from the pull down menu select Properties. Memory • Double data rate 3(DDR3) synchronous dynamic random access memory Storage device • 2.5-inch (76 mm) solid state drive or 2.5-inch (64 mm) hard disk drive • mSATA solid state drive (on some models) Display The color display uses TFT technology: • Size: 12.
Wireless features • Integrated wireless LAN (on some models) • Integrated Bluetooth (on some models) • Integrated wireless WAN (on some models) • Integrated WiMAX (on some models) Security features • Fingerprint reader (on some models) Tablet features • Tablet Digitizer Pen • Touch panel (on select models) Specifications This section provides specifications for your computer. ThinkPad X220 and X220i specifications Size • Width: 305.0 mm (12 inch) • Depth: 206.5 mm (8.13 inch) • Height: 19 to 26.6 mm (0.
Battery pack • Lithium-ion (Li-Ion) battery pack Battery life • For percentage of remaining battery power, see the Power Manager Battery Gauge in the task bar. • The Power Manager also displays a green, yellow and red indication. A battery under warranty with a red indication is eligible for a warranty replacement. ThinkPad X220 Tabet and X220i Tablet specifications Size • Width: 305.0 mm (12 inch) • Depth: 228.7 mm (9 inch) • Height: 27 to 31.3 mm (1.06 inch to 1.
Operating environment This section provides information about your computer operating environment. Environment • Maximum altitude without pressurization: 3048 m (10,000 ft) • Temperature – At altitudes up to 2438 m (8000 ft) Operating: 5.0°C to 35.0°C (41°F to 95°F) Non-operating: 5.0°C to 43.0°C (41°F to 109°F) – At altitudes above 2438 m (8000 ft) Maximum temperature when operating under the unpressurized condition: 31.
• “Product Recovery” on page 37 • “Rescue and Recovery” on page 37 • “System Update” on page 37 • “ThinkVantage GPS” on page 37 • “Lenovo SimpleTap ” on page 38 • “Lenovo ThinkVantage Tablet Shortcut Menu” on page 38 Note: To learn more about ThinkVantage technologies and other computing solutions, offered by Lenovo, go to: http://www.lenovo.
Then, follow the instructions on the screen. When the installation process completes, the application icon will be activated, and you can find the application in Control Panel. The sections in Control Panel, the green texts, and the applications are listed in the following table. Table 2.
Active Protection System The Active Protection System protects your hard disk drive when the shock sensor inside your computer detects a condition that could damage the drive, such as system tilt, excessive vibration, or shock. The hard disk drive is less vulnerable to damage when it is not operating; so the system stops it from spinning, and may also move the read/write heads of the drive to areas that do not contain data.
To access the Lenovo ThinkVantage Tools program, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools. Note: Lenovo ThinkVantage Tools is only available on computers preinstalled with Windows 7. Lenovo ThinkVantage Toolbox The Lenovo ThinkVantage Toolbox is a diagnostic program that works through the Windows operating system.
Product Recovery This program enables you to create recovery media to restore the contents of the system drive or hard disk drive to the same state as when the computer was originally shipped from the factory. For information about how to open and use this program, refer to “Creating and using recovery media” on page 107. Presentation Director Presentation Director is a display configuration utility that enables you to give presentations conveniently.
• Ensure that you place your notebook away from concrete or brick walls that may weaken satellite signals. • Best reception will be available near windows and other locations where cellular phone reception is the strongest.
Chapter 2. Using your computer Your computer is powerful and is loaded with features and applications. Use it to accomplish anything, any day, any time.
On the go and need to use battery power more effectively? • To conserve power, or to suspend operation without exiting applications or saving files, see the explanation about “power-saving modes” on page 59. • To achieve the best balance between performance and power saving, create and apply power plans (in Windows XP, power schemes) by use of Power Manager. • If your computer will be turned off for an extended period of time, you can prevent battery power from draining by removing the battery.
• Also Recovery tool is provided on your computer hard disk or solid state drive. For more information, see Chapter 5 “Recovery overview” on page 107. Print the following sections and keep them with your computer in case you are unable to access this online help when necessary.
3. Close the computer display slowly, holding the upper left and right sides with both hands. Note: Make sure that the display is rotated at 180 degrees, so that the back of the display faces the keyboard. 4. Your computer is now in the tablet mode. To return your computer to the notebook mode, do as follows: 1. Open the display by at least 45 degrees, preferably by 90 degrees.
2. Follow the direction shown by the display swivel indicator and rotate the display slowly (figure below shows counter-clockwise rotation as an example) until the front of the display is facing the keyboard. Your computer is now in the notebook mode. Tips on using your computer in the tablet mode • To close the computer display, first make sure that the display either faces the keyboard or is positioned at 180 degrees to the keyboard, so that the back of the display faces the keyboard.
Note: The pen contains pressure sensors. Do not push the tip of the pen for an extended period of time. Do not subject the pen to shock or vibration. The Tablet Digitizer Pen consists of a tip 2 , a click button 3 , and an eraser tip 4 . Hold the pen and point the tip at the display to move the cursor 1 . To make a selection (single click), tap the display once with the pen. To double-click, tap twice without pausing.
For a single click, tap the display once with your finger. For a double click, tap the display twice without pausing. For a right click, tap the display once and then hold your finger on the display until a circular symbol appears. When you take your finger off the display, the right-click menu will open.
1 Press the Screen Rotation buttonto rotate the screen clockwise. 2 The Secure Attention Sequence button functions the same as the Ctrl+Alt+Del key combination. 3 Press the power button button to turn the computer on or off. Using the Tablet Shortcut Menu Tablet Shortcut Menu is a software tool bar that is optimized for use when your computer is in the tablet mode.
ThinkVantage button The blue ThinkVantage button can help you in many situations when your computer is working normally, and even when it is not. You can also use the ThinkVantage button to interrupt the startup sequence of your computer and start the Rescue and Recovery workspace, which runs independently of the Windows operating system and is hidden from it. If Windows is not running properly, you may need to do the following: • Get the current system information.
To enable or disable the numeric keypad, press and hold Shift or Fn and then press NmLk (ScrLk). Note: The next drawing shows the locations of the keys that serve as the 10-key numeric keypad. The locations of these keys are the same on every keyboard, though for computers using different languages, different characters are printed on the keytops. If the numeric keypad is enabled, press and hold Shift to use the cursor-control and screen-control keys temporarily.
Function key combinations By setting the function keys, you can change operational features instantly. To use this function, press and hold the Fn key 1 ; then press one of the function keys 2 . Power conservation • Fn+F3 Select a power plan (in Windows XP, power scheme) that has been created by Power Manager, or adjust the power level by using the slider control.
– To use Fn+F3, Fn+F4, and Fn+F12 key combinations, you must have the ThinkPad PM device driver installed on your computer. For information on the power management function, refer to “Power management” on page 58. Applying a presentation scheme • Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings.
Notes: If you want to use Fn+F5 to enable or disable the wireless features, the following device drivers must be installed on your computer beforehand: – Power Management driver – OnScreen Display Utility – Wireless device drivers For information on the wireless features, refer to “Wireless connections” on page 62. Launching the camera and audio settings • Fn+F6 If you press Fn+F6, the camera and audio settings window is opened and the camera preview is turned on.
Volume and mute buttons You can adjust the sound level of the built-in speakers by using the following three buttons: If you mute the sound and then turn off your computer, the sound will remain muted when you turn on your computer again. To turn on the sound, press the plus (+) or minus (-) button. Setting the volume Each device has volume controls, which you can set. To open the window for adjusting the output volume or the recording volume, do the following: For Windows 7 and Windows Vista: 1.
• For details about controlling volume, refer to your Windows online help. Setting the microphone mute button in Windows 7 and Windows Vista By default, you can toggle all of your recording devices between the mute state and the un-mute state by pressing the microphone mute button. If you want to toggle one of the recording devices between the mute state and the un-mute state, do the following: 1. Press Fn+F6. The Communications settings window opens. 2. Click the Manage Settings button.
To display the shortcut menu for an object, select the object on the desktop or within an application and then press this key. Using the UltraNav pointing device Your computer may come with the UltraNav pointing device. The UltraNav consists of the TrackPoint and the touch pad, each of which is itself a pointing device with both basic and extended functions. You can configure both devices by choosing the settings you prefer as follows: • Set both the TrackPoint and the touch pad as pointing devices.
If you are not familiar with the TrackPoint, these instructions will help you get started: 1. Place your hands in the typing position, and press gently with either index finger on the pointing stick in the direction in which you want the pointer to move. To move the pointer, press the pointing stick away from you to move it up, toward you to move it down, to one side or the other to move it sideways. Note: The pointer might drift. This is not a defect.
Note: If you replace the keyboard, a new keyboard is shipped with the default cap. If you wish, you can keep the cap from your old keyboard and use it on the new one. Using the touch pad The touch pad is below the TrackPoint buttons at the bottom of the keyboard. To move the pointer 2 on the screen, slide your fingertip over the pad in the direction in which you want the pointer to move. The left and right bottom of the pad work as click buttons.
3. Click the UltraNav tab and proceed to customizing the touch pad. For details, refer to the Help in the Utility. Behavior of the UltraNav and an external mouse By default, the TrackPoint and the touch pad are set to Enabled. Note: If you want to attach an external mouse to a USB connector, select “Disabled.” Disabling the TrackPoint or the touch pad If you want to disable the TrackPoint or the touch pad, do either of the following: • Use the Fn+F8 key combination: 1. Press Fn+F8.
You can now change the properties of UltraNav by clicking the UltraNav icon on the system tray. Power management When you need to use your computer away from electrical outlets, you depend on battery power to keep your computer running. Different computer components consume power at different rates. The more you use the power-intensive components, the faster you consume battery power. Do more, save more and spend more time unplugged with ThinkPad batteries.
– If the battery has not been used for a long time. Before you charge the battery, make sure that its temperature is at least 10°C (50°F). Charging the battery When you check battery status and find that the percentage of power remaining is low or when the power alarm alerts you that remaining power is low, you need to charge your battery or replace it with a charged battery. If an ac outlet is convenient, plug the ac power adapter into it, and then insert the jack into the computer.
2. Select Power off display (keep current power plan) (in Windows XP, keep current power scheme). Notes: You can also turn off the computer display as follows: 1. Press Fn+F3. A panel for selecting a power plan (in Windows XP, power scheme) appears. 2. Select Fn+F3 Settings. 3. Select Power off display. 4. Click OK. The next time you press Fn+F3, you can turn off the computer display. • Sleep (standby in Windows XP).
2. Click the Global Power Settings tab. 3. For Low battery alarm or Critically low battery alarm, set the percentage of the power level and set the action. Note: If your computer enters sleep (standby) or hibernation mode when the battery is low, but the alarm message has not yet appeared, the message will appear when the computer resumes. To resume normal operation, press OK. Handling the battery DANGER Do not attempt to disassemble or modify the battery pack.
DANGER Only recharge the battery pack strictly according to instructions included in the product documentation. DANGER Do not put the battery pack in trash that is disposed of in landfills. When disposing of the battery, comply with local ordinances or regulations and your company's safety standards. DANGER There is a danger of an explosion if the backup battery is incorrectly placed. The lithium battery contains lithium and can explode if it is not properly handled, or disposed of.
Wireless LAN A wireless local area network covers a relatively small geographic area, such as an office building or a house. Devices based on the 802.11 standards can connect to this network. Wireless WAN A wireless wide area network covers a broader geographic area. Cellular networks are used for data transmission, and access is provided by a wireless service carrier. Bluetooth One of a number of technologies used to create a wireless personal area network.
Wireless upgradeable ThinkPad models Your computer can be wireless upgradeable. This means that your computer has an antenna that can support wireless LAN access when wireless LAN access points are available. Wireless devices are available from Lenovo. For more information, see “Finding ThinkPad options” on page 149. Using wireless WAN connections Wireless Wide Area Network (wireless WAN) enables you to establish wireless connections over remote public or private networks.
Note: If you use the wireless feature (the 802.11 standard) of your computer simultaneously with a Bluetooth option, data transmission speed can be delayed and the performance of the wireless feature can be degraded. For Windows XP If your computer is equipped with the Integrated Bluetooth features, you can enable or disable the features by pressing Fn+F5. If you press Fn+F5, a list of wireless features is displayed. You can enable or disable the Bluetooth features with a single click.
To use the Bluetooth features, do the following: 1. Double-click the My Bluetooth Places icon on the desktop. 2. For Windows XP, go to Bluetooth Tasks and double-click View devices in range. A list of the devices on which Bluetooth has been enabled appears. 3. Click the device to which you want access.
For details, refer to the help for Bluetooth. To see the help, double-click My Bluetooth Places, and click Help and then Bluetooth help. Another way to start the help is to right-click Bluetooth Configuration in the system tray of the task bar, and click Advanced Configuration and then Help. Installing the Microsoft Bluetooth software in Windows XP If you want to use the Microsoft Bluetooth software, do as follows: 1. First uninstall the ThinkPad Bluetooth with Enhanced Data Rate Software. a.
2. Click Performance and Maintenance; then click System. 3. Click the Hardware tab; then click Device Manager. 4. Double-click Bluetooth Radios to extract the Bluetooth Radios device tree. 5. Double-click the ThinkPad Bluetooth with Enhanced Data Rate icon to open the Properties window. 6. Click the Driver tab; then click Update Driver. 7. Click No, not this time, and then click Next. 8. Select Install from a list or specific location (Advanced), and then click Next. 9. Select Don't search.
– Power to the wireless radio is on. The signal strength of the wireless connection is excellent. • Access Connections Gauge states: wireless WAN – No signal – Signal level 1 – Signal level 2 – Signal level 3 Note: For more information about Access Connections Gauge, see the Help in Access Connections. Access Connections icon and wireless status icon The Access Connections icon displays general connection status.
Enabling or disabling the wireless feature To enable or disable the wireless feature, press Fn+F5. A list of wireless features is displayed. You can turn the feature on and off with a single click. You can also enable or disable the feature by the following procedures. To enable the wireless feature, do as follows: 1. Click the Access Connections wireless status icon in the system tray. 2. Click Power On Wireless Radio. To disable the wireless feature, do as follows: 1.
3. Under Font Size, click Large Fonts or Extra Large Fonts. 4. Click Apply to apply the settings. 5. Click OK. If you are prompted to restart the computer after you click OK or Apply, the change will take effect after the computer restarts. Numeric lock To change the numeric lock setting, do as follows: For Windows 7: 1. Right-click on the desktop, and click Personalize. 2. Click Display at the left. 3. Click Change display settings. 4.
Connecting an external monitor To attach an external monitor, do as follows: For Windows 7: 1. Connect the external monitor to the monitor connector; then connect the monitor to an electrical outlet 2. Turn on the external monitor. 3. Change the display output location by pressing Fn+F7. This allows you to switch between viewing output on the external display, the computer display, and both displays.
3. Right-click on the desktop, and click Screen resolution. Note: If your computer cannot detect the external monitor, click the Detect button. 4. Set Resolution. 5. Click Advanced Settings. 6. Click the Monitor tab. Check the monitor information window to make sure that the monitor type is correct. If it is, click OK to close the window; otherwise do as follows. 7. If more than two monitor types are displayed, select Generic PnP Monitor or Generic Non-PnP Monitor. 8. Click Properties.
16. Set Resolution and Colors in the Display Settings window. 17. Click OK. For Windows XP: 1. Connect the external monitor to the monitor connector, and then connect the monitor to an electrical outlet. 2. Turn on the external monitor and the computer. 3. Press Fn+F7 to change the display output location to the external monitor. 4. Right-click on the desktop, and click Properties to open the Display Properties window. 5. Click the Settings tab. 6. Click Advanced. 7. Click the Monitor tab.
2. Connect the DVI monitor to the DVI connector of the expansion unit, and then connect the monitor to an electrical outlet. 3. Turn on the DVI monitor and the computer. The system starts. If the computer output does not appear on the DVI monitor, do as follows: For a computer that has the Intel display adapter: 1. Press Ctrl+Alt+F12. The Intel Graphics Media Accelerator Driver for mobile window appears. 2. Select Digital Display, Intel Dual Display Clone, or Extended Desktop.
Playing sound Your projector might have one or more audio-input connectors. To project sound, you will need to attach the combo audio jack on your computer to these connectors, using an audio cable (commercially available). Using dual displays Using the Extend desktop function Your computer supports a function named the Extend desktop. With the Extend desktop function, you can display output on both the computer display and an external monitor. You can also display different desktop images on each monitor.
For Windows Vista: 1. Connect the external monitor to the monitor connector; then connect the monitor to an electrical outlet. 2. Turn on the external monitor. 3. If this is the first time the external monitor has been connected, the New Display Detected dialog box opens. Select Show different parts of my desktop on each display (extended), and then click OK. To change the resolution for each monitor, do as follows: 1. Right-click on the desktop, and click Personalize. 2. Click Display Settings.
• Recording and playback of PCM and WAV files in 16-bit or 24-bit format. • Playback of a WAV file at a sample rate of 44.1KHz to 192 KHz. • Playback of MIDI files through a Wave table synthesizer under Microsoft Windows operating systems. • Playback of MP3 files through the Windows Media Player or a software MP3 player.
You can also use the integrated camera with other programs that provide features such as photographing, video capturing, and video conferencing. To use the integrated camera with other programs, open one of the programs and start the photographing, video capturing, or videoconferencing function. Then, the camera will start automatically and the green camera-in-use indicator will turn on. For more information about using the camera with a program, refer to the documentation that came with the program.
For more information on ExpressCards, smart cards, and flash media cards, refer to any of the following topics: • “Inserting an ExpressCard, a flash media card, or a smart card” on page 80. • “Removing an ExpressCard, a flash media card, or a smart card” on page 81. Inserting an ExpressCard, a flash media card, or a smart card Attention: Do not insert an ExpressCard while the computer is in sleep (standby) mode or hibernation mode. If you do, the computer may not respond when you try to resume using it.
Removing an ExpressCard, a flash media card, or a smart card Attention: Before removing a storage ExpressCard, such as a flash memory ExpressCard, a solid state ExpressCard, or a memory card reader ExpressCard, from an ExpressCard slot, you must stop the ExpressCard. Otherwise, data on the ExpressCard might be corrupted or lost. Attention: Do not remove an ExpressCard while the computer is in sleep (standby) mode or hibernation mode. If you do, the system will not respond when you try to resume operation.
82 User Guide
Chapter 3. You and your computer This chapter provides you information about accessibility and traveling with your computer. This chapter contains the following topics: • “Accessibility and comfort” on page 83 • “Traveling with your computer” on page 86 Accessibility and comfort Because your computer enables you to work in so many places, it is important that you remain attentive to good posture, good lighting and proper seating.
clean and set the brightness to levels that enable you to see the screen clearly. Press Fn+Home or End to adjust display brightness. Head Position: Keep your head and neck in a comfortable and neutral (vertical, or upright) position. Chair: Use a chair that gives you good back support and seat height adjustment. Use chair adjustments to best suit your desired posture. Arm and Hand Position: If available, utilize chair arm rests or an area on your working surface to provide weight support for your arms.
Accessibility information Lenovo is committed to providing people with disabilities greater access to information and technology. As a result, the following information provides ways to help users that have hearing, vision, and mobility limitations get the most out of their computer experience. Assistive technologies enable users to access information in the most appropriate way.
To disable the FullScreen Magnifier function, click the FullScreen Magnifier icon and select Exit or press Fn+Spacebar. Traveling with your computer When you travel abroad, your computer can help you feel more at home and at ease. With your own computer and its files, you can be confident about gathering and offering information to clients and coworkers.
• A quality carrying case that provides adequate cushion and protection If you are traveling to another country you might want to consider these items: • An ac power adapter for the country that you are traveling to • An adapter to connect to a phone line in that country Other items you may wish to consider: • ThinkPad ac/dc Combo Adapter • External storage device • Phone line splitter, in case you need to dial manually or use your modem without disconnecting the phone line Chapter 3.
88 User Guide
Chapter 4. Security This chapter provides information about how to protect your computer from theft and unauthorized use.
• “Supervisor password” on page 93 Passwords and sleep (standby) mode If you have set passwords and you put your computer into sleep (standby) mode by pressing Fn+F4, the procedure for resuming operation is as follows: • You are not prompted to type the password when resuming operation. • If any hard disk or the solid state drive has a hard disk password, it is unlocked automatically when you resume operation. Typing passwords If this icon appears, enter the Power-on password or Supervisor password.
Note: You might want to note your power-on password in a safe place. Otherwise, if you forget it, you have to take your computer to a Lenovo reseller or a marketing representative to have the password canceled. 11. Press F10 to exit. Changing or removing the power-on password To change the power-on password, follow the steps 1 through 9 above in “Setting a power-on password” on page 90, typing your password to get access to the ThinkPad Setup. To change the password, do the following: 1.
8. A Setup Confirmation window opens. You are prompted to select User or User + Master. Select User if you want to set only one hard disk password. If you are an administrator or supervisor, you can select User + Master to set two passwords. (The user can change the user password later.) 9. If you select User + Master, go to step 12. 10. If you select User only, a new-password window opens. Type your new password in the Enter New Password field.
Setup Notice window is displayed. Press F10 to exit from the Setup Notice window. The user hard disk password will be removed. To change or remove the User + Master hard disk password, select User HDP or Master HDP. If you choose User HDP, do one of the following: • To change the user hard disk password, type the current user hard disk password or the current master hard disk password in the Enter Current Password field.
– Enabling or disabling the Flash BIOS Updating by End-Users feature – Enabling or disabling the Internal Network device – Enabling or disabling the Internal Wireless device – Enabling or disabling the Internal Bluetooth device – Enabling or disabling the Internal Wireless WAN device – Enabling or disabling the Security mode – Enabling or disabling the Reader priority – Erasing the fingerprint data Notes: • The system administrator can set the same supervisor password on many ThinkPad notebooks to make admi
3. Follow step 11 and step 12 above in “Setting a supervisor password” on page 94 to change your supervisor password. To remove the password, do the following: 1. In the Enter Current Password field, type the current supervisor password. 2. Leave the Enter New Password and Confirm New Password fields in blank. 3. Follow step 11 and step 12 above in “Setting a supervisor password” on page 94 to remove your supervisor password.
For details about Windows BitLocker Drive Encryption, go to the Help and Support for Windows 7 or Windows Vista, or search for “Microsoft Windows BitLocker Drive Encryption Step-by-Step Guide” on Microsoft web site. Disk Encryption hard disk drive and Encryption solid state drive Some models contain the Disk Encryption hard disk drive or Encryption solid state drive.
7. Using the cursor keys, move to an item you want to set. When the item you want is highlighted, press Enter. 8. Set the items you want to set. 9. Press F10 to exit. 10. Click Yes in the Setup Confirmation window. To set the Security Chip, you have to open the Client Security Solution, and follow the instructions on the screen. Note: If your computer is a Windows 7 model, Client Security Solution is not preinstalled on your system.
LED behavior of the fingerprint reader Table 4. LED behavior list_fingerprint reader Indicator Description LED blinks green. The fingerprint is being authenticated or has been authenticated. LED is solid green. The fingerprint reader is ready to swipe. LED blinks amber. The fingerprint could not be authenticated. Swiping your finger over the reader To swipe your finger over the reader, do as follows: 1.
2. Apply light pressure and swipe your finger across the reader in one smooth motion. Logging on to the system After you enroll your fingerprint, log on to the system as follows: 1. Set a Power-on password or a Hard disk security, or both. 2. Turn your computer off and then on again. 3. When prompted, swipe your finger over the reader. 4. On request, type your power-on password, your hard disk password, or both.
To set an item in the fingerprint submenu: 1. Print these instructions. To configure the fingerprint reader, you must turn your computer off and then on again. 2. Save all open files, and exit all applications. 3. Turn your computer off and then on again. 4. When the logo screen is displayed, press F1. The ThinkPad Setup opens. 5. Using the cursor keys, move to Security, and press Enter. The Security menu opens. 6. Using the cursor keys, move to Fingerprint, and press Enter. The Fingerprint submenu opens.
swiping your finger over the reader, without typing a password. Thus fingerprint authentication can replace passwords and enable simple and secure user access. For more advanced security, Client Security Solution can be installed. The software is compatible with a variety of user authentication mechanisms, such as those involving fingerprint authentication. This fingerprint reader can work with the software. Note: If your computer is a Windows 7 model, Client Security Solution is not preinstalled on it.
1. Place the ball of your finger, that is, the central part of the fingerprint, on the small circle above the reader. Make sure that the entire top joint of the finger is on the reader. 2. Apply light pressure and swipe your finger across the reader in one smooth motion.
1. Place the ball of your finger, that is, the central part of the fingerprint, on the small circle above the reader. Make sure that the entire top joint of the finger is on the reader. 2. Apply light pressure and swipe your finger across the reader in one smooth motion. Logging on to the system After you enroll your fingerprint, log on to the system as follows: 1. Set a Power-on password or a Hard disk security, or both. 2. Turn your computer off and then on again. 3.
If you forget your hard disk password, Lenovo cannot reset your password or recover data from the hard disk. You must take your computer to a Lenovo authorized servicer or a marketing representative to have the hard disk drive replaced. Proof of purchase is required, and a fee will be charged for parts and service. Setting the fingerprint reader If you want to change the settings of the fingerprint reader, follow the procedure below.
• Your finger is very dry. • Your finger is stained with dirt, mud, or oil. • The surface of your finger is very different from when you enrolled your fingerprint. • Your finger is wet. • A finger is used that has not been enrolled. To improve the situation, try the following: • Clean or wipe your hands to remove any excess dirt or moisture from the fingers. • Enroll and use a different finger for authentication. • If your hands are too dry, apply lotion to them.
decrypted without the old key. This feature is enabled by the ThinkPad Setup Menu Extension Utility and is available as a menu item in the ThinkPad Setup. Using and understanding firewalls If your system is preintalled with a firewall program, it protects against computer Internet security threats, unauthorized access, intrusions, and Internet attacks. It also protects your privacy. For more information about how to use the firewall program, refer to the on-line help that comes with the program.
Chapter 5. Recovery overview This chapter provides information about the recovery solutions provided by Lenovo. This chapter contains the following topics: • “Creating and using recovery media” on page 107 • “Performing backup and recovery operations” on page 109 • “Using the Rescue and Recovery workspace” on page 110 • “Creating and using a rescue medium” on page 111 • “Reinstalling preinstalled applications and device drivers” on page 112 • “Solving recovery problems” on page 113 Notes: 1.
Creating recovery media This section provides instructions on how to create recovery media on the Windows 7 operating system. Note: On the Windows 7 operating system, you can create recovery media using discs or external USB storage devices. On the Windows Vista and Windows XP operating systems, you can create recovery media using only discs, so this operation is also called “creating Product Recovery discs.
1. Repeatedly press and release the F12 key when turning on the computer. When the Startup Device Menu opens, release the F12 key. 2. Insert the boot disc into the optical drive. 3. Select the optical drive with the boot disc as the startup device and press Enter. After a short delay, the Rescue and Recovery workspace opens. 4. On the Rescue and Recovery menu, click Restore your system. 5. Follow the instructions on the screen. Insert the appropriate Product Recovery disc when prompted.
1. From the Windows desktop, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Enhanced Backup and Restore. The Rescue and Recovery program opens. 2. In the Rescue and Recovery main window, click the Launch advanced Rescue and Recovery arrow. 3. Click the Restore your system from a backup icon. 4. Follow the instructions on the screen to complete the recovery operation.
Note: If the Rescue and Recovery workspace fails to open, see “Solving recovery problems” on page 113. 4. Do one of the following: • To rescue files from your hard disk drive or from a backup, click Rescue files and follow the instructions on the screen. • To restore your hard disk drive from a Rescue and Recovery backup or to restore your hard disk drive to the factory default settings, click Restore your system and follow the instructions on the screen.
• If you have created a rescue medium using a disc, use the following instructions to use the rescue medium: 1. Turn off your computer. 2. Repeatedly press and release the F12 key when turning on the computer. When the Startup Device Menu opens, release the F12 key. 3. On the Startup Device Menu, select the desired optical drive as the first boot device. Then, insert the rescue disc into the optical drive and press Enter. The rescue medium starts.
5. Open the subfolder for the device. 6. Reinstall the device driver using one of the following methods: • In the subfolder for the device, look for a text file (a file with the extension .txt). The text file contains information on how to reinstall that device driver. -OR• If the subfolder for the device contains a file of setup information (a file with the extension .inf), you can use the Add New Hardware program (in the Windows Control Panel) to reinstall the device driver.
114 User Guide
Chapter 6. Replacing devices You can increase the capacity of the memory or the hard disk drive by replacing the original, built-in device with an optional one. Or, if you need to, you can replace the PCI Express Mini Card by following the procedures in this section.
Replacing the battery Before you start, print these instructions. This system may not support batteries that are not genuine Lenovo-made or authorized. These systems will continue to boot, but may not charge unauthorized batteries. Attention: Lenovo has no responsibility for the performance or safety of unauthorized batteries, and provides no warranties for failures or damage arising out of their use.
3. Unlock the battery latch by sliding it to the unlock position. 4. Remove the battery. 5. Slide the battery into the computer. Chapter 6.
6. Slide the battery latch to the locked position. 7. Turn the computer over again. Connect the ac power adapter and the cables to the computer. Replacing the keyboard Before you start, print these instructions. You can use the following procedures to replace the keyboard with a new one, available as an option. Prerequisites for the procedure DANGER During electrical storms, do not connect the cable to or disconnect it from the telephone outlet on the wall.
4. Loosen the two screws on the memory slot cover , then remove the cover. 5. Turn the computer over and open the display. 6. Push hard in the direction shown by the arrows 1 in the drawing to unlatch the front side of the keyboard. The keyboard will open up slightly 2 . Chapter 6.
7. Carefully lift the keyboard until you can see how it's connected. Hold the keyboard above the computer 1 , and then detach the connector 2 . Now the keyboard has been removed. Installing the keyboard 1. Attach the connector.
2. Insert the keyboard. Make sure that the rear edges of the keyboard are under the frame as shown by the arrows. 3. Press gently on the areas marked in the drawing, and slide the keyboard toward you. Make sure that the edges of the keyboard marked in the drawing, are under the frame. Chapter 6.
4. Put the memory slot cover back in place , close the cover , and then tighten the screws. 5. Reinstall the battery. For details, refer to the instructions in “Reinstall the battery” on page 116. 6. Turn the computer over again. Connect the ac power adapter and cables to the computer; then turn it on. Replacing the palm rest Before you start, print these instructions.
6. Turn the computer over and open the display. Lift up the left and right top edges of the palm rest to remove it. 7. Detach the flip-lock ZIF connector 1 , then remove the palm rest cable 2 . 8. Lift up and remove the palm rest. Chapter 6.
9. Release the palm rest from the computer. Now the palm rest has been removed. Installing the palm rest 1. Attach the palm rest, making sure the latches near the top left and right edges of the palm rest are secure. 2. Push the front side of the palm rest until it clicks into place. 3. Attach the flip-lock ZIF connector 1 , then push the palm rest cable 2 .
4. Reinstall the screws for the palm rest. 5. Reinstall the keyboard. For more information about how to remove the keyboard, refer to Replacing the keyboard. 6. Reinstall the battery. For more information, refer to Replacing the battery. 7. Turn the computer over again. Connect the ac power adapter and cables to the computer; then turn it on. Replacing the hard disk drive Before you start, print these instructions.
• Do not drop the drive or subject it to physical shocks. Put the drive on a material, such as soft cloth, that absorbs any physical shocks. • Do not apply pressure to the cover of the drive. • Do not touch the connector. The drive is very sensitive. Incorrect handling can cause damage and permanent loss of data. Before removing the hard disk drive, make a backup copy of all the information on it, and then turn the computer off.
6. Detach the side rubber rails from the hard disk drive. 7. Attach the side rubber rails to a new hard disk drive. 8. Insert the hard disk drive into the hard disk drive bay, then press it firmly into place. Chapter 6.
9. Insert the slot cover 1 . Then, slide in the cover 2 and reinstall the screw 3 . 10. Reinstall the battery. For details, refer to the instructions in “Reinstall the battery” on page 116. 11. Turn the computer over again. Connect the ac power adapter and the cables to the computer. Replacing the solid state drive You can replace the solid state drive with a new one which can be purchased from your Lenovo reseller or a marketing representative.
4. Remove the screw that secures the solid state drive 1 . Then flip out the cover 2 and pull up to remove it 3 . 5. Remove the solid state drive by pulling out the tab. 6. Detach the side spacer rails from the hard disk drive. Chapter 6.
7. Attach the side spacer rails to a new hard disk drive. 8. Insert the solid state drive into the hard disk drive bay, then press it firmly into place. 9. Reinstall the cover of the bay 1 , then reinstall the screw 2 . 10. Reinstall the battery. For more information about how to reinstall the battery, refer to “Replacing the battery” on page 116. 11. Turn the computer over again. Connect the ac power adapter and the cables to the computer.
Installing and replacing the PCI Express Mini Card for wireless LAN/WiMAX connection Before you start, print these instructions. Your computer has a PCI Express Mini Card slot for connection to a wireless LAN/WiMAX. To replace the PCI Express Mini Card with a new one, read the following prerequisites. Prerequisites for the procedure DANGER During electrical storms, do not connect the cable to or disconnect it from the telephone outlet on the wall.
6. If a tool for removing connectors is included in the package with the new card, use it to disconnect the cables from the card. If no such tool is included, disconnect the cables by picking up the connectors with your fingers and gently unplugging them. 7. Remove the screw. The card pops up.
8. Remove the card. 9. Align the contact edge of the new PCI Express Mini Card with the corresponding socket contact of the computer. Chapter 6.
10. Pivot the card until you can snap it into place by pressing the upper side of the connectors 1 , and secure the card with the screw 2 . 11. Connect the cables to the new PCI Express Mini Card. Be sure to attach the gray cable to the connector marked “MAIN” or “M” on the card, and the black cable to the connector marked “AUX” or “A.
4. Remove the keyboard. For details, refer to the instructions in “Remove the keyboard” on page 118. 5. Remove the palm rest. For details, refer to the instructions in “Remove the palm rest” on page 122. 6. If a tool for removing connectors is included in the package with the new card, use it to disconnect the cables from the card. If no such tool is included, disconnect the cables by picking up the connectors with your fingers and gently unplugging them. 7. Remove the screw. The card pops up. Chapter 6.
8. Remove the card. 9. Align the contact edge of the new PCI Express Mini Card with the corresponding socket contact of the computer.
10. Pivot the card until you can snap it into place by pressing the upper side of the connectors 1 , and secure the card with the screw 2 . 11. Connect the cables to the new PCI Express Mini Card. Be sure to attach the gray cable to the connector marked “MAIN” or “M” on the card, and the black cable to the connector marked “AUX” or “A.
Some ThinkPad models have a PCI Express Mini Card slot for connection to a wireless WAN. To replace the PCI Express Mini Card with a new one, read the following prerequisites. Prerequisites for the procedure DANGER During electrical storms, do not connect the cable to or disconnect it from the telephone outlet on the wall. DANGER Electric current from power, telephone, and communication cables is hazardous. To avoid shock hazard, disconnect the cables before opening the cover of this slot.
7. Remove the screw. The card pops up. 8. Remove the card. Chapter 6.
9. Align the contact edge of the new PCI Express Mini Card with the corresponding socket. Note: You can also replace the PCI Express Mini Card for Wireless WAN with an mSATA solid state drive. 10. Pivot the card until you can snap it into place by pressing the upper side of each connector. Secure the card with the screw. Note: Depending on the system configuration of your computer, the card may have only one connector.
11. Connect the cables to the new PCI Express Mini Card. 12. Reinstall the palm rest. For details, refer to the instructions in “Reinstall the palm rest” on page 122. 13. Reinstall the keyboard. For details, refer to the instructions in “Reinstall the keyboard” on page 118. 14. Reinstall the battery. For details, refer to the instructions in “Reinstall the battery” on page 116. 15. Turn the computer over again. Connect the ac power adapter and cables to the computer; then turn it on.
If an mSATA solid state drive is available in your computer, to replace the mSATA solid state drive, do as follows. 1. Turn off the computer; then disconnect the ac power adapter and all cables from the computer. Wait for a few minutes, till the inside of the computer cools, before you start the following procedures. 2. Close the computer display, and turn the computer over. 3. Remove the battery. For details, refer to the instructions in “Remove the battery” on page 116. 4. Remove the keyboard.
8. Align the contact edge of a new mSATA solid state drive with the corresponding socket. Note: You can also replace the mSATA solid state drive with a Wireless PCI Express Mini Card for Wireless WAN. 9. Pivot the card downward 1 until you can snap it into place. Secure the card with the screw 2 . 10. Reinstall the palm rest. For details, refer to the instructions in “Reinstall the palm rest” on page 122. 11. Reinstall the keyboard.
Note: The operating speed of the memory module depends on the system configuration of your computer and its combination with the memory module installed on your computer. In some conditions, the memory in your computer may not be able to operate at the maximum speed. Attention: Before you start installing a module, touch a metal table or a grounded metal object. This action reduces any static electricity from your body. The static electricity could damage the SO-DIMM.
6. With the notched end of the SO-DIMM toward the contact edge side of the socket, insert the SO-DIMM into the socket at an angle of about 20 degrees 1 ; then press it in firmly 2 . Note: If you install a memory module in only one of the two memory slots, install it in the lower slot. 7. Pivot the SO-DIMM downward until it snaps into place. 8. Make sure that the SO-DIMM is firmly fixed in the slot and cannot be moved easily. 9.
2. When the logo screen is displayed, press the F1 key. The ThinkPad Setup opens. The “Installed memory” item shows the total amount of memory installed in your computer. Replacing the SIM card Before you start, print these instructions. Your computer may require a SIM (Subscriber Identification Module) card to establish a wireless WAN (Wide Area Network) connections.
5. Insert the SIM card firmly into the slot. Note: Make sure that you insert the SIM card all the way into the slot. 6. Put the battery back in place. For more details, refer to “Replacing the battery” on page 116. 7. Turn the computer over again, and reconnect the cables. Chapter 6.
148 User Guide
Chapter 7. Enhancing your computer This section provides information on installing devices and taking advantage of your computer's high-technology features.
ThinkPad Ultrabase Series 3 top view 1 The docking connector is used for attaching the ThinkPad computer to the ThinkPad Ultrabase Series 3. 2 The power jack is where you connect the AC adapter. 3 The Ethernet connector is for connecting the ThinkPad Ultrabase Series 3 to a LAN. 4 The DisplayPort connector is for connecting a DisplayPort-compatible display device. 5 The Monitor connector is for attaching an external monitor or a projector to your computer.
ThinkPad Ultrabase Series 3 bottom view 1 By pressing the eject request button, you can tell the operating system to get ready for undocking. 2 The docking indicator is red when your computer is docked. It blinks when the eject request button is pressed. 3 The eject lever detaches your computer from the ThinkPad Ultrabase Series 3. 4 The holes are for the system speakers.
2. Align the front of the computer with the front of the ThinkPad Ultrabase Series 3. 3. Make sure that the guides of the ThinkPad Ultrabase Series 3 align with the holes of the computer 1 . Then put the computer in place 2 . The docking indicator lights.
4. When the computer is already docked to the ThinkPad Ultrabase Series 3, you can start the computer. Note: You can turn the key clockwise to lock it. Then, keep the security key in a safe place. Do not lose this key; otherwise, you will be unable to detach the computer from the ThinkPad Ultrabase Series 3. Detaching a ThinkPad Ultrabase Series 3 Attention: Do not detach your computer from the ThinkPad Ultrabase Series 3 while the docking indicator of the ThinkPad Ultrabase Series 3 is blinking or on.
• the battery is fully charged. To detach your computer from the ThinkPad Ultrabase Series 3, do the following: 1. Make sure that the system lock key of the ThinkPad Ultrabase Series 3 is in the unlocked (vertical) position. 2. Close the computer display. 3. If you are hot/warm-detaching the computer, press the eject request button of the ThinkPad Ultrabase Series 3. Then make sure that the eject inhibit indicator of the ThinkPad Ultrabase Series 3 is off, and the eject ready indicator lights up. 4.
1 Unlock position: If the UltraBase lock is in this position, your computer is not secured. 2 Base lock position: If the UltraBase lock is in this position, the ThinkPad Ultrabase Series 3 is locked, and the computer cannot be removed from the ThinkPad Ultrabase Series 3. The Serial Ultrabay Slim device is also locked and cannot be removed from the UltraBase. Note: Keep the security key in a safe place.
Top view 1 The docking connector is used for attaching the ThinkPad computer to the ThinkPad Battery 19+. Bottom view 1 The power jack is where you connect the AC adapter. 2 By pressing the indicator button, the status indicator shows the ThinkPad Battery 19+ charge status. 3 The status indicator is to show the ThinkPad Battery 19+ charge status. 4 The eject lever is to release the ThinkPad Battery 19+ from the docking connector in the computer.
2. Make sure that the guides of the ThinkPad Battery 19+ align with the holes of the computer 1 . Then put the computer in place 2 . Detaching a ThinkPad Battery 19+ To detach a ThinkPad Battery 19+, do the following: 1. Unlock the battery latch by sliding it to the unlock position. Chapter 7.
2. Release the eject lever 2 and pull up the ThinkPad Battery 19+. Charging a ThinkPad Battery 19+ The ThinkPad Battery 19+ can be charged separately.
The ThinkPad Battery 19+ can also be charged with a computer. When the ThinkPad Battery 19+ is charged with a computer, both the main battery and ThinkPad Battery 19+ can be charged simultaneously. ThinkPad Port Replicator Series 3, ThinkPad Mini Dock Series 3, and ThinkPad Mini Dock Plus Series 3 Note: Only ThinkPad X220 and X220i support ThinkPad Port Replicator Series 3, ThinkPad Mini Dock Series 3, and ThinkPad Mini Dock Plus Series 3.
• “Front view” on page 160 • “Rear view” on page 163 • “Attaching a ThinkPad Port Replicator Series 3, ThinkPad Mini Dock Series 3, or ThinkPad Mini Dock Plus Series 3” on page 166 • “Detaching a ThinkPad Port Replicator Series 3, ThinkPad Mini Dock Series 3, and ThinkPad Mini Dock Plus Series 3” on page 168 • “Security feature” on page 170 • “Using the system lock key” on page 172 Front view ThinkPad Port Replicator Series 3 1 The power switch turns the computer on and off.
ThinkPad Mini Dock Series 3 1 The power switch turns the computer on and off. 2 The key lock indicator lights when the system lock key is in the locked position. When the system lock key is in the locked position, the eject button of the ThinkPad Mini Dock Series 3 is locked; you cannot attach or remove your computer. 3 The docking indicator lights when your computer is docked. 4 The eject button releases the computer from the ThinkPad Mini Dock Series 3 when pressed.
ThinkPad Mini Dock Plus Series 3 1 The power switch turns the computer on and off. 2 The key lock indicator lights when the system lock key is in the locked position. When the system lock key is in the locked position, the eject button of the ThinkPad Mini Dock Plus Series 3 is locked; you cannot attach or remove your computer. 3 The docking indicator lights when your computer is docked. 4 The eject button releases the computer from the ThinkPad Mini Dock Plus Series 3 when pressed.
Rear view ThinkPad Port Replicator Series 3 1 The power jack is for connecting the ac power adapter. 2 The Ethernet connector is for connecting the ThinkPad Port Replicator Series 3 to an Ethernet LAN. The indicator on the connector is the same as that on the computer. Notes: • You cannot use the Token Ring cable for this connector. • You can use this connector for a 10BASE-T/100BASE-TX/1000BASE-T Ethernet.
ThinkPad Mini Dock Series 3 1 The power jack is for connecting the ac power adapter. 2 The DisplayPort is for connecting a display device. 3 The digital visual interface connector is for connecting a monitor that supports Single-Link DVI. Note: The DVI connector provides a digital interface only. This connector can be used with a computer that supports DVI via docking only. 4 The headphone jack, a jack 1/8 inch (3.5 mm) in diameter, is for connecting an external stereo headphone.
ThinkPad Mini Dock Plus Series 3 1 The DisplayPort is for connecting a display device. 2 The digital visual interface connector is for connecting a monitor that supports Single-Link DVI. Note: The DVI connector provides a digital interface only. This connector can be used with a computer that supports DVI via docking only. 3 The DisplayPort is for connecting a display device. 4 The digital visual interface connector is for connecting a monitor that supports Single-Link DVI.
10 When you attach a mechanical lock to the security keyhole, the eject button is locked so that the computer cannot be removed from the ThinkPad Mini Dock Plus Series 3.
2. Press the button of the ThinkPad Mini Dock Series 3, or the ThinkPad Mini Dock Plus Series 3 1 . Pull the sliding adjuster in the direction shown by the arrow 2 . 3. Put your computer on the platform of the ThinkPad Mini Dock Series 3, or the ThinkPad Mini Dock Plus Series 3, making sure that the top-left corner of the computer is aligned to the guide plate on the ThinkPad Mini Dock Series 3, or the ThinkPad Mini Dock Plus Series 3. 4.
• If your computer and the ThinkPad Port Replicator Series 3, the ThinkPad Mini Dock Series 3, or the ThinkPad Mini Dock Plus Series 3 are connected to separate ac power adapters, your computer goes into battery mode first, and then shifts into ac mode. • If in either of the two preceding situations the battery of your computer is detached, or has no battery charge, your computer shuts down.
3. Press the eject button 1 until the computer moves up; then, grasp both sides, and remove the computer 2 . To detach your computer from the ThinkPad Port Replicator Series 3, do the following: Notes: • If your computer is operating, make sure that it has finished operations involving devices that are connected to the USB connector. Also make sure that any Ethernet connection is stopped. • Make sure that the battery pack is fully charged. 1.
Security feature The ThinkPad Port Replicator Series 3, the ThinkPad Mini Dock Series 3, or the ThinkPad Mini Dock Plus Series 3 has a security keyhole for a mechanical lock. By attaching a mechanical lock with cable there, you can secure the ThinkPad Port Replicator Series 3, the ThinkPad Mini Dock Series 3, or the ThinkPad Mini Dock Plus Series 3 to a heavy object, such as a desk.
Attach a mechanical lock to the ThinkPad Mini Dock Series 3 as follows: Attach a mechanical lock to the ThinkPad Port Replicator Series 3 as follows: Chapter 7.
Using the system lock key The system lock key has two positions, unlocked and locked. When the key is in the locked position, the eject button of the ThinkPad Mini Dock Series 3 or the ThinkPad Mini Dock Plus Series 3 is locked, and you cannot remove your computer. The key lock indicator lights when the eject button is locked.
Chapter 8. Advanced configuration While it is important to protect files, data, and settings that are on the hard disk or on the solid state drive, you may also need to install a new operating system, install new device drivers, update your UEFI BIOS, or recover preinstalled software. This information will help you handle your computer with proper care and keep it in top working shape.
Country or region: Code China: SC Denmark: DK Finland: FI France: FR Germany: GR Italy: IT Japan: JP Netherlands: NL Netherlands: NL Norway: NO Spain: SP Sweden: SV Taiwan and Hong Kong: TC United States: US Installing Windows 7 Before you start, print these instructions. To install Windows 7 and its related software on your computer, do as follows: 1. Start the ThinkPad Setup. 2. Select Startup menu. 3. Select UEFI/Legacy Boot. 4.
Note: The Web site address might change without notice. If the homepage is not displayed, search for it from the Microsoft top page. To install a fix module, run the EXE file in a subfolder and follow the instructions on the screen. Note: If you remove the hard disk drive from the computer with a single-core processor and install it on a computer with a dual-core processor, you can get access to the hard disk drive.
Installing the Windows Vista Update Module Package The Windows Vista Update Modules are in the following directory: C:\SWTOOLS\OSFIXES\. The name of each subfolder is the number of a fix module. For information about each fix module, go to the Microsoft Knowledge Base homepage at http://support.microsoft.com/, type the number of the fix module you need in the search field, and click Search. Note: The Web site address might change without notice.
16. To continue the installation, press Enter again. Leave the diskette in the drive until the next reboot; the software may need to be copied from the diskette again when the files are copied during setup. 17. Complete the installation of Windows XP Service Pack 2 by following OS installing instructions. 18. Install Windows XP Service Pack 3.
23. When the System Settings Change window appears, click Yes. The computer restarts. 24. Install the Intel Chipset Support for Windows 2000/XP/Vista/7. To do this, refer to “Installing Intel Chipset Support for Windows 2000/XP/Vista/7” on page 180. 25. Apply the PCMCIA Power Policy Registry Patch. To do this, go to C:\SWTOOLS\OSFIXES\PCMCIAPW\, double-click install.bat, and then follow the instructions that appear on the screen. 26. Install device drivers.
4. Click Next. If the device driver is already installed, click Cancel. Follow the instructions on the screen until the installation is finished. Installing ThinkPad Monitor File for Windows 2000/XP/Vista/7 ThinkPad Monitor File for Windows 2000/XP/Vista/7 is in the following directory: C:\SWTOOLS\DRIVERS\MONITOR. Note: If you cannot find this directory on your hard disk drive or solid state drive, download the ThinkPad Monitor File for Windows 2000/XP/Vista/7 from the ThinkPad Web site at: http://www.
11. Click OK. 12. Confirm the correct display type, then click Next. 13. Windows has finished installing. Click Close. 14. Click Close for Display Properties. 15. Click OK in the Monitor tab. 16. Click OK and close the Display Settings window. For Windows XP 1. Right-click on the desktop and select Properties from the pop-up menu. 2. Select the Settings tab. 3. Click the Advanced tab. 4. Select the Monitor tab. 5. Select Plug and Play Monitor from the monitor type list. 6. Click Properties. 7.
Installing drivers and software The device drivers are provided in the C:\SWTOOLS\DRIVERS directory on your hard disk drive. You will also need to install application software, which is provided in the C:\SWTOOLS\APPS directory on your hard disk drive. To do this, refer to the instructions in “Reinstalling preinstalled applications and device drivers” on page 112.
4. Using the cursor keys, move to an item you want to change. When the item you want is highlighted, press Enter. A submenu is displayed. 5. Change the items you wish to change. To change the value of an item, press +/-. If the item has a submenu, you can display it by pressing Enter. 6. Press Esc to exit from the submenu. 7. If you are in a nested submenu, press Esc repeatedly until you reach the ThinkPad Setup menu.
Security menu If you need to set the security features of your computer, select Security from the ThinkPad Setup menu. Notes: • The default settings are already optimized for you. If you consider changing the computer configuration, proceed with extreme caution. Setting the configuration incorrectly might cause unexpected results. • In each submenu, you can enable a function by selecting Enabled, or disable it by selecting Disabled.
If you select and enable Password at unattended boot, a password prompt is displayed when the computer is turned on, from either a power-off state or hibernation, by an unattended event such as Wake on LAN®. If you select Disabled, no password prompt is displayed; the computer goes ahead and loads the operating system. To prevent unauthorized access, set the user authentication on the operating system.
2. USB FDD: 3. ATAPI CD0: 4. ATA HDD0: 5. ATA HDD1: 6. ATA HDD2: 7. USB HDD: 8. PCI LAN: 9. ATAPI CD1: 10. ATAPI CD2: 11. ATA HDD3: 12. ATA HDD4: 13. Other CD: 14. Other HDD: Network Boot Use the Network Boot to select the boot device when the system wakes from LAN. If Wake-on-LAN is enabled, the network administrator can turn on all of the computers in a LAN remotely by use of network management software.
• Enabled means that the function is configured. • Disabled means that the function is not configured. • Default values are in boldface. Config menu items Table 6. Config menu items Menu item Submenu item Selection Comments Network Wake On LAN • Disabled Enable the system to Power on when the Ethernet controller receives a magic packet. • AC only • AC and Battery If you select “AC Only”, Wake On LAN is enabled only when ac power adapter is attached.
Table 6. Config menu items (continued) Menu item Submenu item Selection Comments Always On USB Charge in off mode • Disabled If you select “Enabled”, the Always On USB connector enables you to charge some devices, such as iPod and iPhone and BlackBerry smartphones.
Table 6. Config menu items (continued) Menu item Submenu item Selection Comments Fn Key Lock • Disabled If you select “Enabled”, you can press the Fn key to keep it in a pressed condition, and then press the desired function key. The action is equivalent to pressing the required key and the Fn key simultaneously. If you press the Fn key twice, the state is locked until you press the Fn key again.
Table 6. Config menu items (continued) Menu item Submenu item Selection Comments Display Boot Display Device • ThinkPad LCD Select the display device that is to be active at boot time. This selection is effective for boot time, password prompt, and ThinkPad Setup. • Analog (VGA) • Digital on ThinkPad • Digital 1 on dock • Digital 2 on dock “Digital on Thinkpad” is DisplayPort on your computer. “Digial 1 on dock” and “Digital 2 on dock” are DisplayPort or DVI on docking station.
Table 6. Config menu items (continued) Menu item Submenu item Selection Comments Adaptive Thermal Management Scheme for AC This selects a thermal management scheme to use. • Maximize Performance • Balanced Scheme for Battery • Maximize Performance • Balanced Maximize Performance: Reduces CPU throttling Balanced: Balances sound, temperature and performance Note: Each scheme affects fan sound, temperature, and performance.
Table 6. Config menu items (continued) Menu item Submenu item Selection Comments Beep and Alarm Power Control Beep • Disabled If this function is enabled, a beep sounds when the computer enters a power management mode, when it resumes operational mode, and when the ac power adapter is connected or disconnected.
Table 6. Config menu items (continued) Menu item Submenu item Selection Comments Intel AMT Intel AMT Control • Disabled If you select “Enabled”, Intel AMT (Active Management Technology) is configured and additional setup items are provided in MEBx (Management Engine BIOS Extension) Setup. • Enabled Note: You can enter MEBx Setup menu by pressing Ctrl-P key combination in Startup Interrupt Menu. To display the Startup Interrupt Menu, press ThinkVantage button or Enter key during POST.
Table 7. Security menu items (continued) Menu item Submenu item Selection Comments Security Mode • Normal If fingerprint authentication fails, you can still start the computer by entering a password. If you have selected “Normal”, enter a power-on password or a supervisor password; if you have selected “High”, enter a supervisor password. • High Password Authentication • Disabled • Enabled Security Chip Enable or disable password authentication.
Table 7. Security menu items (continued) Menu item Submenu item Selection Comments Clear Security Chip • Enter Clear the encryption key. Note: Only if you select “Active” for Security Chip, this item appears.
Table 7. Security menu items (continued) Menu item Submenu item Selection Comments I/O Port Access Ethernet LAN • Disabled If you select “Enabled”, you can use the Ethernet LAN device.
Table 7. Security menu items (continued) Menu item Submenu item Selection Comments Anti-Theft Intel AT Module Activation • Disabled Enable or disable the UEFI BIOS interface to activate Intel AT module that is an optional Anti-Theft service from Intel. • Enabled • Permanently Disabled Note: If you set the Intel AT module activation to “Permanently Disabled”, you will be unable to enable this setting again.
Table 8. Startup menu items (continued) Menu item Selection Comments Boot Mode • Quick Screen during POST: • Diagnostics • Quick: ThinkPad Logo screen is displayed. • Diagnostics: Text messages are displayed. Note: You can also enter the “Diagnostic” mode by pressing Esc during POST.
Once the computer is configured and operational, you can manage it by use of software and manageability features already integrated into the client system and the network.
6. Select the Allow this device to wake the computer check box. For Windows XP: 1. Click Start, and then click Control Panel. 2. Click Performance and Maintenance. 3. Click System. 4. Click the Hardware tab. 5. Click the Device Manager button. The Device Manager window opens. 6. Click the + mark for Modems, and then click your modem. 7. Click Action, and then click Properties. 8. Click the Power Management tab. 9. Select the Allow this device to bring the computer out of Standby check box.
Network Boot sequence When your computer is turned on remotely, system will try to boot from the device that is selected by Network Boot setting, and then follow the boot order list in the Boot menu. To define a sequence: 1. On the ThinkPad Setup menu, select Startup. The Startup submenu appears. 2. Select Network Boot and press Enter key to show pop-up boot device list. 3. Select a boot device from the list to make it as top boot priority. 4. Press F10.
Chapter 9. Preventing problems An important part of owning a ThinkPad notebook is maintenance. With proper care, you can avoid common problems. The following sections provide information that can help you to keep your computer running smoothly. • “General tips for preventing problems” on page 201 • “Making sure device drivers are current” on page 202 • “Taking care of your computer” on page 203 General tips for preventing problems 1. Check the capacity of your hard disk drive from time to time.
14. If required, you can find your country's Customer Support Center at the following Web address: http://www.lenovo.com/support/site.wss/document.do?sitestyle=lenovo&lndocid=migr-4hwse3. When calling the Customer Support Center, please make sure you have your machine model type, serial number and the computer in front of you. Also, if the machine is producing error codes, it is helpful to have the error screen on or the message written down.
Taking care of your computer Although your computer is designed to function reliably in normal work environments, you need to use common sense in handling it. By following these important tips, you will get the most use and enjoyment out of your computer. Be careful about where and how you work • Store packing materials safely out of the reach of children to prevent the risk of suffocation from plastic bags.
• When installing the hard disk drive, solid state drive, or optical drive, follow the instructions shipped with your hardware, and apply pressure only where needed on the device. • Turn off your computer if you are replacing the hard disk drive or solid state drive. • When replacing the primary hard disk drive or solid state drive, reattach the cover of the drive slot. • Store your external and removable hard disk or optical drives in the appropriate containers or packaging when they are not being used.
Tips on using the built-in modem • Your computer modem may use only an analog telephone network, or public-switched telephone network (PSTN). Do not connect the modem to a PBX (private branch exchange) or any other digital telephone extension line because this could damage your modem. Analog phone lines are often used in homes, while digital phone lines are often used in hotels or office buildings. If you are not sure which kind of phone line you are using, contact your telephone company.
5. Wipe the display again; do not let any liquid drip into the computer. 6. Be sure to dry the display before closing it.
Chapter 10. Troubleshooting computer problems This chapter provides information on helping your solve computer problems. • “Diagnosing problems” on page 207 • “Troubleshooting” on page 207 Diagnosing problems If you experience problems with your computer, use the following procedure as a starting point for solving them. Using Lenovo ThinkVantage Toolbox Note: If your system is running and User Guide is accessible, see User Guide.
Computer stops responding Print these instructions now and keep it with your computer for reference later. If your computer is completely unresponsive (you cannot use the UltraNav pointing device or the keyboard), do the following steps: 1. Push and hold the power switch until the machine turns off. After the computer is turned off, restart by pressing the power switch. If the machine does not turn on, continue to step 2. Note: Do not remove the battery and ac power to reset the computer. 2.
Error messages • Message: 0176: System Security - The System has been tampered with. Solution: This message is displayed if you remove the Security Chip and reinstall it, or install a new one. To clear the error, enter the ThinkPad Setup. If this does not solve the problem, have the computer serviced. • Message: 0177: Bad SVP data, stop POST task. Solution: Checksum of the supervisor password in the EEPROM is not correct. The system board should be replaced. Have the computer serviced.
Solution: The system CMOS might have been corrupted by an application program. The computer uses the default settings. Run the ThinkPad Setup to reconfigure the settings. If you still see the same error code, have the computer serviced. • Message: 0253: EFI Variable Block Data was destroyed. Solution: The system EFI Variable Block Data might have been corrupted. 1. Press F1 to go to the ThinkPad Setup. 2. Press F9 and then press Enter to load the default setting. 3.
Solution: A power-on password or a supervisor password is set. Type the password and press Enter to use the computer (refer to “Using passwords” on page 89). If the power-on password is not accepted, a supervisor password might have been set. Type the supervisor password and press Enter. If you still see the same error message, have the computer serviced. • Message: The hard disk password prompt Solution: A hard disk password is set.
– If you have used the partition software, examine the partition on the hard disk drive or solid state drive by using the software, and recover the partition if required. – Use either the Rescue and Recovery workspace or the recovery discs to restore the system to the factory state. For details about restoring the system to the factory state, see “Creating and using recovery media” on page 107. If the problem persists, have the computer serviced. • Problem: My screen goes blank while the computer is on.
Solution: Make sure that: – The cable is installed properly. The network cable must be securely connected both to the Ethernet connector of your computer and to the RJ45 connector of the hub. The maximum allowable distance from the computer to hub is 100 meters. If the cable is connected and the distance is within acceptable limits but the problem persists, try a different cable. – You are using the correct device driver. For Windows 7 and Windows Vista: 1. Click Start, and then click Control Panel. 2.
– If it is, check with your LAN administrator for the necessary settings. • Problem: If your computer is a Gigabit Ethernet model, it cannot connect to the network at 1000 Mbps. Instead, it connects at 100 Mbps. Solution: – Try another cable. – Make sure that the link partner is set to auto-negotiate. – Make sure that the switch is 802.3ab-compliant (gigabit over copper). A wireless LAN problem • Problem: You cannot connect using the built-in wireless networking card.
For Windows XP Notes: If you are using the Microsoft standard Bluetooth features and you want to access information about how to use the Bluetooth function, do the following: 1. Press Fn+F5 to turn on Bluetooth. 2. Click Start ➙ Control Panel. 3. Click Printers and Other Hardware. 4. Click Bluetooth Devices. 5. Click the Options tab. 6. Click Learn more about Bluetooth Settings Note: If you are using the ThinkPad Bluetooth with Enhanced Data Rate Software, refer to the following instructions.
Make sure that the security settings on the connected computer allow you to upload your business card. • Problem: Your computer is connected to a Bluetooth-enabled computer that works as an FTP server, but you cannot see any files in the FTP server. Solution: Check the newly shared files as follows: 1. In the menu of My Bluetooth Places, click View. 2. Click Update. The status is updated in the window, so that you can check the newly shared files.
If the words “Bluetooth Radio” appear in the device listing, the Microsoft Bluetooth software is installed on your computer. If you want to use ThinkPad Bluetooth with Enhanced Data Rate Software, you have to install it and then replace the Bluetooth driver. For more information, see “Using Bluetooth” on page 64. • Problem: While looking at the Classic View of the Control Panel, you see two Bluetooth icons in the Control Panel.
If the keyboard problem is resolved, carefully reconnect the external numeric keypad, external keyboard, making sure that you have seated the connectors properly. If the problem remains, make sure that the correct device driver is installed. For Windows 7: 1. Click Start ➙ Control Panel. Change the view of the Control Panel from Category to Large icons or Small icons. 2. Click Keyboard. 3. Select the Hardware tab. In the Device Properties, make sure that the Device Status is This device is working properly.
Solution: Make sure that: – The display device driver is installed correctly. – The screen resolution and color quality are correctly set. – The monitor type is correct. To check these settings, do as follows: For Windows 7: 1. Right-click on the desktop, and click Personalize. 2. Click Display at the left. 3. Select Change display settings. Check whether the screen resolution is correctly set. 4. Click Advanced Settings. 5. Click the Adapter tab. 6.
6. Make sure that the correct device driver name is shown in the adapter information window. Note: The device driver name depends on the video chip that has been installed on your computer. 7. Click the Properties button. Check the “Device status” box and make sure the device is working properly. If not, click the Troubleshoot button. 8. Click the Monitor tab. 9. Make sure the information is correct. 10. Click the Properties button. Check the “Device status” box and make sure the device is working properly.
5. Make sure that the correct device driver name is shown in the adapter information window. Note: The device driver name depends on the video chip that has been installed on your computer. 6. Click OK. If the information is incorrect, reinstall the device driver. See below for more information. For Windows Vista: 1. Right-click on the desktop and click Personalize. 2. Click Display Settings. 3. Click the Advanced Settings button. 4. Click the Adapter tab. 5.
12. Clear the Show compatible hardware check box. 13. Select Manufacturer and Model for your monitor. 14. After updating the driver, click Close. 15. Set Resolution. Note: To change the color settings, select the Monitor tab, then set Colors. 16. Click OK. For Windows Vista: 1. Connect the external monitor to the monitor connector, and then connect the monitor to an electrical outlet. 2. Turn on the external monitor and the computer. 3.
8. If more than one monitor type is displayed, select Default Monitor. 9. Click Properties. 10. Click the Driver tab. 11. Click Update Driver. The Hardware Update Wizard appears. 12. Click No, not this time, and then click Next. 13. Select Install from a list or specific location (Advanced), and then click Next. 14. Select Don't search. I will choose the driver to install, and then click Next. 15. Clear the Show compatible hardware check box. 16. Select Manufacturers and Models for your monitor. 17.
1. Connect the external monitor to the monitor connector, and then connect the monitor to an electrical outlet. 2. Turn on the external monitor and the computer. 3. Press Fn+F7 to change the display output location to the external monitor. Note: After pressing Fn+F7, you will need to wait for a moment before the image appears. 4. Right-click on the desktop, and click Properties to open the Display Properties window. 5. Click the Settings tab. 6. Click Advanced. 7. Click the Monitor tab. 8.
9. Select the Resolution and Colors of the secondary display. 10. Set the relative position of the each monitor by dragging its icon. You can set the monitors in any relative position, but the icons must touch each other. 11. Click OK to apply the changes. For Windows XP: 1. Attach the computer to an external monitor. 2. Right-click on the desktop, and click Properties to open the Display Properties window. 3. Click the Settings tab. 4. Click the Monitor-2 icon. 5.
Solution: Make sure the built-in audio device is configured correctly. For Windows 7 and Windows Vista: 1. Click Start ➙ Control Panel. 2. Click Hardware and Sound. 3. Click Device Manager. If you are prompted for an administrator password or confirmation, type the password or provide confirmation. 4. Double-click Sound, video and game controllers (in Windows Vista, click the + mark for Sound, video and game controllers). 5.
Solution: The slider might be grayed out. This means that its position is fixed by the hardware and cannot be changed. • Problem: The volume sliders do not stay in place when some audio applications are used. Solution: It is normal for the sliders to change position when certain sound applications are used. The applications are aware of the Volume Mixer window (in Windows XP, Volume Control window) and are allowed to change the settings themselves. An example is the Windows Media Player.
• Problem: When you connect a headphone to your computer while playing sound, a speaker does not produce sound in the MULTI-STREAM mode at SmartAudio (Windows 7). Solution: Once the headphone is attached, the streaming is automatically redirected to it. If you want to listen to sound from the speakers again, be sure to set those speakers as the default device. The procedure is as follows: 1. Click Start ➙ Control Panel ➙ All Control Panel Items. 2. Click the SmartAudio icon. The SmartAudio window opens. 3.
1. Turn off the computer. 2. Make sure that the over-discharged battery pack is in the computer. 3. Connect the ac power adapter to the computer and let it charge. If the optional Quick Charger is available, use it to charge the over-discharged battery pack. If the battery pack cannot be fully charged in 24 hours, use a new battery pack. • Problem: Your computer shuts down before the battery status indicator shows empty, -or- Your computer operates after the battery status indicator shows empty.
4. Verify the ac power source is working by attaching another device to the outlet. 5. Remove the computer from a ThinkPad Ultrabase Series 3. Refer to “Detaching a ThinkPad Ultrabase Series 3” on page 153. 6. Remove all devices and then test for system power with minimal devices attached. a. Disconnect the ac power adapter and all cables from the computer. b. Close the computer display, and turn the computer over. c. Remove the battery. Refer to “Replacing the battery” on page 116. d.
Solution: If the processor overheats, the computer automatically enter sleep (standby) mode to allow the computer to cool and to protect the processor and other internal components. Check the settings for sleep (standby) mode, using Power Manager. • Problem: The computer enters sleep (standby) mode (the sleep/standby indicator turns on) immediately after Power-on self-test. Solution: Make sure that: – The battery is charged. – The operating temperature is within the acceptable range.
For Windows XP: 1. Click Start ➙ Control panel. 2. Click Performance and Maintenance. 3. Click Power Options. 4. Click the Hibernate tab. 5. Click the Enable hibernation check box. 6. Click OK. If you want to be able to enter hibernation mode by pressing Fn+F12, you need to install ThinkPad PM driver. • Problem: The battery discharges slightly while the computer is in hibernation mode. Solution: If the wakeup function is enabled, the computer consumes small amount of power. This is not a defect.
– The application is designed to operate with your operating system. – Other applications run correctly on your computer. – The necessary device drivers are installed. – The application works when it is run on some other computer. If an error message appears while you are using the application program, refer to the manuals supplied with the application. If the application still does not run correctly, contact your place of purchase or a service representative for help.
234 User Guide
Chapter 11. Getting support There is more to owning a ThinkPad notebook than having a powerful, portable computer. This chapter offers information about when to communicate with Lenovo and how best to do it.
Getting help and service If you need help, service, technical assistance, or just want more information about Lenovo products, you will find a wide variety of sources available from Lenovo to assist you. This section contains information about where to go for additional information about Lenovo and our products, what to do if you experience a problem with your computer, and whom to call for service should it be necessary.
• Lenovo hardware repair - If the problem is determined to be caused by Lenovo hardware under warranty, trained service personnel are available to provide the applicable level of service. • Engineering change management - Occasionally, there might be changes that are required after a product has been sold. Lenovo or your reseller, if authorized by Lenovo, will make selected Engineering Changes (ECs) available that apply to your hardware.
Table 10. World-wide telephone list (continued) Country or Region Telephone Number Brunei 801-1041 (English and Bahasa Melayu) Canada 1-800-565-3344 (English and French) Caribbean (Bermuda, Jamaica, and Tortola) 1-877-426-7378 (English) Chile 800-361-213 188-800-442-488 (Toll free) (Spanish) China Technical Support Line 800-990-8888 86-10-58851110 (Mandarin) China (Hong Kong S.A.R.
Table 10.
Table 10.
Table 10. World-wide telephone list (continued) Country or Region Telephone Number Venezuela 0-800-100-2011 (Spanish) Vietnam For Northern Area and Hanoi City: 844 3 946 2000 or 844 3 942 6457 For Southern Area and Ho Chi Minh City: 848 3 829 5160 or 844 3 942 6457 (Vietnamese and English) In all other countries and regions, contact your Lenovo reseller or marketing representative, or go to the Lenovo support Web site at: http://www.lenovo.
242 User Guide
Appendix A. Regulatory Information This appendix includes regulatory information for users. Wireless related information Wireless interoperability Wireless LAN PCI Express Mini Card is designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS), Complementary Code Keying (CCK), and/or Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is compliant to: • The 802.11b/g Standard, 802.11a/b/g or 802.11n draft 2.
Due to the fact that integrated wireless cards operate within the guidelines found in radio frequency safety standards and recommendations, Lenovo believes they are safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
ThinkPad 220 Tablet and X220i Tablet 1. Wireless WAN (Auxiliary) If your computer comes with a wireless WAN feature, its auxiliary antenna is located at the top left side of the computer display. 2. Wireless LAN and WiMAX combo antenna (Auxiliary) The auxiliary antenna connected to the wireless LAN or WiMAX feature is located at the top left portion of the computer display, near the center. 3.
4. You can then find the Regulatory Notice in the displayed search results. Export classification notice This product is subject to the United States Export Administration Regulations (EAR) and has an Export Classification Control Number (ECCN) of 4A994.b. It can be re-exported except to any of the embargoed countries in the EAR E1 country list. Electronic emission notices The following information refers to ThinkPad 4294, 4296, 4297, 4298, 4299, 4300, 4301, 4286, 4287, 4289, 4290, 4291, 4292, and 4293.
European Union - Compliance to the Electromagnetic Compatibility Directive This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the installation of option cards from other manufacturers.
Korea Class B compliance statement Japan VCCI Class B compliance statement Japan compliance statement for products which connect to the power mains with rated current less than or equal to 20 A per phase Lenovo product service information for Taiwan Pointer to the printed pub for additional regulatory information For additional regulatory information, refer to the Regulatory Notice shipped with your computer.
Appendix B. WEEE and recycling statements Lenovo encourages owners of information technology equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products. Information on product recycling offerings can be found on Lenovo's Internet site at: http://www.pc.ibm.com/ww/lenovo/about/environment/.
Disposing of a Lenovo computer components Some Lenovo computer products sold in Japan may have components that contain heavy metals or other environmental sensitive substances. To properly dispose of disused components, such as a printed circuit board or drive, use the methods described above for collecting and recycling a disused computer or monitor.
Appendix C. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo Access Connections Active Protection System Rescue and Recovery ThinkLight ThinkPad ThinkVantage TrackPoint Ultrabay Ultrabase UltraConnect UltraNav Intel and Intel SpeedStep are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.
