Lenovo 3000 N100 and N200 Hardware Maintenance Manual June 2007 This manual supports: Lenovo 3000 N100 (MT 0689 and 0768) Lenovo 3000 N200 (MT 0769)
Lenovo 3000 N100 and N200 Hardware Maintenance Manual
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 155. Second Edition (June 2007) © Copyright Lenovo 2007. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents Introduction . . . . . . . . . . . . . 1 About this manual . . . . . . . . . . . Important service information . . . . . . . Strategy for replacing FRUs . . . . . . . . Strategy for replacing a hard disk drive . . . Important notice for replacing a system board . How to use error messages . . . . . . . Strategy for replacing FRUs for Custom Model Variant (CMV) products . . . . . . . . . Using PC Entitlement Warehouse (PEW) . . . Using eSupport . . . . . . . . . . . Using the HMM . . . . . . . . . .
iv MT 0689, 0768, and 0769
Introduction About this manual This manual contains service and reference information for Lenovo 3000 N100 and N200 (MT 0689, 0768, and 0769). Use this manual along with the advanced diagnostic tests to troubleshoot problems. The manual is divided into sections as follows: v The common sections provide general information, guidelines, and safety information required in servicing computers. v The product-specific section includes service, reference, and product-specific parts information.
Important service information v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one.
Important service information Using PC Entitlement Warehouse (PEW) v PEW is the primary source for identifying FRU part numbers and FRU descriptions for the key commodities for CMV products at a MT - serial number level. An example of key commodities are hard disk drives, system boards, microprocessors, Liquid Crystal Displays (LCDs), and memory. v Remember, all CMV products are loaded in PEW under the 4-digit MT and 3-digit model, where model = “fixed part number”.
Important service information Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.
Diskette compatibility matrix Diskette compatibility matrix The compatibility of each of the drives with the diskettes for it is as follows: Diskette drive Diskette capacity Compatibility 3.5-inch 1.0 MB Read and write 2.0 MB Read and write 4.0 MB Not compatible Safety notices: multilingual translations In this manual, safety notices appear in English with a page number reference to the appropriate multilingual, translated safety notice found in this section.
Safety notices Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium.
Safety notices Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
Safety notices Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium.
Safety notices Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing. Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes.
Safety notices Safety notice 7 DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d’une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves.
Safety information Safety information The following section presents safety information with which you need to be familiar before you service a Lenovo 3000 computer. General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force.
Safety information Important Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock. v Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet.
Safety information v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.) v If an electrical accident occurs: – Use caution; do not become a victim yourself. – Switch off power. – Send another person to get medical aid.
Safety information Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes 1.
Laser compliance statement Laser compliance statement Some models of Lenovo 3000 computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products.
Laser compliance statement A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir.
General descriptions The descriptions in this chapter apply to any Lenovo 3000 model that has the PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to your particular computer. Read this first Before you go to the checkout guide, be sure to read this section. Important notes v Only certified trained personnel should service the computer. v Before replacing any FRU, read the entire page on removing and replacing FRUs. v When you replace FRUs, use new nylon-coated screws.
Read this first Following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use.
Related service information Related service information This section provides information about the following: v “Service Web site” v “Restoring the factory contents by using Product Recovery discs” v “Passwords” on page 20 v “Power management” on page 22 Service Web site When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.
Related service information 9. When prompted, insert the appropriate Product Recovery disc and then click OK. The second phase of the recovery process begins. 10. When all of the data has been copied from the last Product Recovery disc in the set, a message is displayed prompting you to restart the computer. Remove the disc and then click Yes, then a message is displayed asking you to continue the recovery process.
Related service information How to remove the power-on password To remove a POP that you have forgotten, do the following: (A) If no SVP has been set: 1. Turn off the computer. 2. Remove the battery pack. For how to remove the battery pack, see “1010 Battery pack” on page 46. 3. Remove the DIMM slot cover. For how to remove the DIMM slot cover, see “1060 DIMM slot cover” on page 53. 4. Remove the DIMM. For how to remove the DIMM, see “1070 DIMM” on page 54. 5. Short J1 pad ( a ). a 6.
Related service information How to remove the hard-disk password Attention: If User only mode is selected and the user HDP has been forgotten and cannot be made available to the servicer, neither Lenovo nor Lenovo authorized servicers provide any services to reset the user HDPs or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee. To remove a user HDP that has been forgotten, when the SVP and the master HDP are known, do the following: 1.
Related service information v If the battery indicator blinks orange, indicating that the battery power is low. (Alternatively, if Hibernate when battery becomes low has been selected in the “Power Management Properties” window, the computer goes into hibernation mode.) To cause the computer to return from sleep (standby) mode and resume operation, do one of the following: v Press the Fn key. v Open the LCD cover. v Turn on the power switch.
Checkout guide Checkout guide Use the following procedures as a guide in identifying and correcting problems with the Lenovo 3000 computer. Note: The diagnostic tests are intended to test only Lenovo 3000 products. The use of non-Lenovo 3000 products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms.
Checkout guide To run the test, do as follows: 1. Insert the PC-Doctor disk into the diskette drive; then power on the computer. If the computer cannot be powered on, go to “Power system checkout” on page 26, and check the power sources. If an error code appears, go to “Symptom-to-FRU index” on page 36. On the first screen, select the model and press Enter. Follow the instructions on the screen. 2. The main panel of PC-Doctor appears. 3. Select Diagnostics with the arrow keys, and press Enter.
Checkout guide Detecting system information with PC-Doctor PC-Doctor can detect the following system information: Hardware Info v v v v v v v v v v v System Configuration Memory Contents Physical Disk Drives Logical Disk Drives VGA Information IDE Drive Info PCI Information PNPISA Info SMBIOS Info VESA LCD Info Hardware Events Log Utility v v v v v v v v v v v Run External Tests Surface Scan Hard Disk Benchmark System DOS Shell Tech Support Form Battery Rundown View Test Log Print Log Save Log Full Era
Checkout guide Checking the ac adapter You are here because the computer fails only when the ac adapter is used. v If the power-on indicator does not turn on, check the power cord of the ac adapter for correct continuity and installation. v If the computer does not charge during operation, go to ″Checking operational charging.″ To check the ac adapter, do the following: 1. Unplug the ac adapter cable from the computer. 2. Measure the output voltage at the plug of the ac adapter cable.
Checkout guide Note: If the battery pack becomes hot, it may not be able to charge. Remove it from the computer and leave it at room temperature for a while. After it cools down, reinstall and recharge it. To check the battery pack, do the following: 1. Power off the computer. 2. Remove the battery pack and measure the voltage between battery terminals 1 (+) and 7 (−). See the following figure: 1(+) 3 2(+) 4 5 7(-) 6(-) Terminal Voltage (V dc) 1 + 0 to + 12.6 7 Ground (−) 3.
Lenovo 3000 N100 and N200 Product overview . . . . . . . . . . . . Specifications . . . . . . . . . . . . . Status indicators . . . . . . . . . . . . FRU tests . . . . . . . . . . . . . . Fn key combinations . . . . . . . . . . Symptom-to-FRU index . . . . . . . . . . Numeric error codes . . . . . . . . . . Error messages . . . . . . . . . . . . No-beep symptoms . . . . . . . . . . . LCD-related symptoms . . . . . . . . . Intermittent problems . . . . . . . . . . Undetermined problems . . . . . . . . .
Product overview Product overview This section presents the following product-unique information: v “Specifications” v “Status indicators” on page 33 v “FRU tests” on page 34 v “Fn key combinations” on page 35 Specifications The following table lists the specifications of the Lenovo 3000 N100 and N200: Feature Description Processor v Intel® Celeron® M processor 410 (1.46 GHz), 1-MB L2 cache (533 MHz) v Intel Celeron M processor 420 (1.60 GHz), 1-MB L2 cache (533 MHz) v Intel Celeron M processor 430 (1.
Product overview Feature Description Processor • Intel Celeron processor 530 (1.73GHz 533MHz 1MBL2) • Intel Celeron processor 550 (2.0GHz 533MHz 1MBL2) • Intel Core 2 Duo processor T5550 (1.83GHz 667MHz 2MBL2) • Intel Core 2 Duo processor T2330 (1.6GHz 533MHz 1MBL2) • Intel Core 2 Duo processor T2310 (1.46GHz 533MHz 1MBL2) • Intel Core 2 Duo processor T5250 (1.5GHz 667MHz 2MBL2) • Intel Core 2 Duo processor T5450 (1.66GHz 667MHz 2MBL2) • Intel Core 2 Duo processor T5470 (1.
Product overview Feature Description Hard disk drive • • • • • • 40 GB, 5400 rpm, 9.5 mm high, SATA interface 60 GB, 5400 rpm, 9.5 mm high, SATA interface 80 GB, 5400 rpm, 9.5 mm high, SATA interface 100 GB, 5400 rpm, 9.5 mm high, SATA interface 120 GB, 5400 rpm, 9.5 mm high, SATA interface 160 GB, 5400 rpm, 9.5 mm high, SATA interface Supported hard disk drives are depend on the model. 32 Optical drive • CD-ROM drive, 12.7 mm high • DVD/CD-RW combo drive, 12.7 mm high • DVD-RAM/RW drive, 12.
Product overview Status indicators The system status indicators show the status of the computer, as follows: 1 2 3 4 5 Indicator 6 7 8 Meaning 1 Caps lock Caps Lock mode is enabled. You can enter all alphabetic characters (A-Z) in uppercase without pressing the Shift key. To enable or disable Caps Lock mode, press the CapsLk key. 2 Num lock The numeric keypad on the keyboard is enabled. To enable or disable the keypad, press and hold the Fn key, and press the NmLk key.
Product overview Indicator 6 Meaning Bluetooth status R Green: Bluetooth wireless is operational. This indicator is on when Bluetooth wireless is on and not in suspend mode. 7 Battery status Green: The battery is charged between 80% to 100% of the capacity, and being discharged between 0% to 80% of the capacity. Blinking green: The battery is charged between 20% to 80% of the capacity, and being charged. Orange: The battery is charged between 5% and 20% of the capacity, and being discharged.
Product overview Fn key combinations The following table shows the function of each combination of Fn with a function key. Key combination Description Fn+F1 Volume down. Fn+F2 Volume up. Fn+F3 Reserved. Fn+F4 Put the computer in sleep (standby) mode. To return to normal operation, press the Fn key only, without pressing a function key. Fn+F5 Enable or disable the built-in wireless networking features and the Bluetooth features. If you press Fn+F5, a list of wireless features is displayed.
Symptom-to-FRU index Symptom-to-FRU index The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type. Note: Do the FRU replacement or other actions in the sequence shown in the column headed “FRU or action, in sequence.” If replacing a FRU does not solve the problem, put the original part back in the computer. Do not replace a nondefective FRU.
Symptom-to-FRU index Symptom or error FRU or action, in sequence 0260 System timer error 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 3. System board. 0270 Real time clock error 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 3. System board.
Symptom-to-FRU index Error messages Symptom or error FRU or action, in sequence Unsupported memory. DIMM. Make sure to use supported memory. Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Failing bits: nnnn. 1. DIMM. 2. System board. Invalid system configuration data. 1. DIMM. 2. System board.
Symptom-to-FRU index No-beep symptoms Symptom or error FRU or action, in sequence No beep, power-on indicator on, LCD blank, 1. Make sure that every connector is and no POST. connected tightly and correctly. 2. DIMM. 3. System board. No beep, power-on indicator on, and LCD blank during POST. 1. Reseat DIMM. The power-on password prompt appears. A power-on password or a supervisor password is set. Type the password and press Enter. The hard-disk password prompt appears. A hard-disk password is set.
Symptom-to-FRU index LCD-related symptoms Important The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns.
Symptom-to-FRU index Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3.
FRU replacement notices FRU replacement notices This section contains notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the Lenovo 3000 computer, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten.
FRU replacement notices v “Retaining the UUID” v “Reading or writing the ECA information” Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer. If you replace the system board, you must restore the serial number of the system unit to its original value.
FRU replacement notices To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write function on the CE Utility Diskette for Lenovo 3000 notebooks. 1. Insert the CE Utility Diskette for Lenovo 3000 notebooks, and restart the computer. 2. From the main menu, select 6. Set ECA Information. 3. To read ECA information, select 2. Read ECA/rework number from EEPROM and follow the instruction. 4. To read box build date, select 5.
Removing and replacing a FRU Removing and replacing a FRU This section presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 42. 3. Begin by removing any FRUs that have to be removed before the failing FRU.
Removing and replacing a FRU 1010 Battery pack DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Unlock the battery release lever 1 and holding the battery release lever in the unlocked position 2 , remove the battery pack in the direction shown by arrow 3 .
Removing and replacing a FRU 1020 Hard disk drive slot cover For access, remove this FRU: v “1010 Battery pack” on page 46 2 1 1 For MT 0689 and 0768 Step Screw (quantity) Color Torque 1 M2.5 × 4 mm, flat-head, nylon-coated (2) Silver 0.392 Nm (4 kgfcm) For MT 0769 Step Screw (quantity) Color Torque 1 M2.5 × 4 mm, pan-head, nylon-coated (2) Silver 0.
Removing and replacing a FRU 1030 Hard disk drive For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover” on page 47 Attention v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible.
Removing and replacing a FRU 1040 PCI Express Mini Card for 802.11 a/b/g wireless LAN For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover” on page 47 For MT 0689 and 0768 1 1 2 3 Step Screw (quantity) Color Torque 1 M2 × 4 mm, flat-head, nylon-coated (2) Black 0.245 Nm (2.
Removing and replacing a FRU For MT 0769 1 2 1 3 Step Screw (quantity) Color Torque 1 M2.5 × 3 mm, pan-head, nylon-coated (2) Silver 0.392 Nm (4 kgfcm) In step 2 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. When installing: Plug the black cable into the jack labeled MAIN on the card, and the white cable into the jack labeled AUX.
Removing and replacing a FRU 1050 PCI Express Mini Card for 802.11 a/b/g/n wireless LAN For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover” on page 47 For MT 0689 and 0768 1 1 2 3 Step Screw (quantity) Color Torque 1 M2 × 4 mm, flat-head, nylon-coated (2) Black 0.245 Nm (2.
Removing and replacing a FRU For MT 0769 1 2 1 3 Step Screw (quantity) Color Torque 1 M2.5 × 3 mm, pan-head, nylon-coated (2) Silver 0.392 Nm (4 kgfcm) In step 2 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Removing and replacing a FRU 1060 DIMM slot cover For access, remove this FRU: v “1010 Battery pack” on page 46 1 2 For MT 0689 and 0768 Step Screw (quantity) Color Torque 1 M2.5 × 4 mm, flat-head, nylon-coated (1) Silver 0.392 Nm (4 kgfcm) For MT 0769 Step Screw (quantity) Color Torque 1 M2.5 × 4 mm, pan-head, nylon-coated (1) Silver 0.
Removing and replacing a FRU 1070 DIMM For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1060 DIMM slot cover” on page 53 2 1 1 When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.
Removing and replacing a FRU 1080 Optical drive For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1060 DIMM slot cover” on page 53 (only for MT 0689) For MT 0689 1 2 3 Step Screw (quantity) Color Torque 1 M2.5 × 4 mm, flat-head, nylon-coated (1) Silver 0.
Removing and replacing a FRU For MT 0768 and 0769 1 2 3 For MT 0768 Step Screw (quantity) Color Torque 1 M2.5 × 4 mm, flat-head, nylon-coated (1) Silver 0.392 Nm (4 kgfcm) For MT 0769 56 Step Screw (quantity) Color Torque 1 M2.5 × 4 mm, pan-head, nylon-coated (1) Silver 0.
Removing and replacing a FRU 1090 Thermal module slot cover For access, remove this FRU: v “1010 Battery pack” on page 46 1 1 2 For MT 0689 and 0768 Step Screw (quantity) Color Torque 1 M2.5 × 4 mm, flat-head, nylon-coated (2) Silver 0.392 Nm (4 kgfcm) For MT 0769 Step Screw (quantity) Color Torque 1 M2.5 × 4 mm, pan-head, nylon-coated (2) Silver 0.
Removing and replacing a FRU 1100 Fan For access, remove this FRU: v “1010 Battery pack” on page 46 v “1090 Thermal module slot cover” on page 57 1 2 1 1 3 For MT 0689 Step Screw (quantity) Color Torque 1 M2.5 × 5 mm, flat-head, nylon-coated (3) Black 0.392 Nm (4 kgfcm) For MT 0768 Step Screw (quantity) Color Torque 1 M2.5 × 6 mm, flat-head, nylon-coated (3) Silver 0.392 Nm (4 kgfcm) For MT 0769 Step Screw (quantity) Color Torque 1 M2.
Removing and replacing a FRU 1110 Thermal module For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1090 Thermal module slot cover” on page 57 v “1100 Fan” on page 58 For MT 0689 and 0768 1 1 1 1 2 Step Screw (quantity) Color Torque 1 CPU thermal screw, nylon-coated (4) Silver 0.392 Nm (4 kgfcm) When installing: Make sure that the connector is attached firmly.
Removing and replacing a FRU For MT 0769 1 2 1 1 When installing: Make sure that the connector is attached firmly.
Removing and replacing a FRU When installing: Before you attach a new thermal module to the computer, peel off the covering film of thermal grease. Then attach the thermal module to the computer.
Removing and replacing a FRU 1120 CPU For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1090 Thermal module slot cover” on page 57 v “1100 Fan” on page 58 v “1110 Thermal module” on page 59 Attention: CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling. Rotate the head of the screw in the direction shown by arrow 1 to release the lock; then remove the CPU in the direction shown by arrow 2 .
Removing and replacing a FRU 1130 Cover, strip (E cover) For access, remove this FRU: v “1010 Battery pack” on page 46 1 2 3 3 Lenovo 3000 N100 and N200 63
Removing and replacing a FRU 1140 Bluetooth daughter card (BDC) for MT 0769 For access, remove this FRU: v “1010 Battery pack” on page 46 v “1130 Cover, strip (E cover)” on page 63 1 2 3 Step Screw (quantity) Color Torque 1 M2.5 × 3 mm, pan-head, nylon-coated (1) Silver 0.392 Nm (4 kgfcm) When installing: Make sure that the connector is attached firmly.
Removing and replacing a FRU 1150 Keyboard For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1130 Cover, strip (E cover)” on page 63 1 1 For MT 0689 and 0768 Step Screw (quantity) Color Torque 1 M2.5 × 3 mm, flat-head, nylon-coated (2) Black 0.392 Nm (4 kgfcm) For MT 0769 Step Screw (quantity) Color Torque 1 M2.5 × 3 mm, pan-head, nylon-coated (2) Black 0.
Removing and replacing a FRU In step 2 , unlatch the keyboard. 2 When installing: Make sure that the latch is attached firmly. Then secure the screws. Lift the keyboard a little in the direction shown by arrow 4 . Then unlock the connector 5 and detach the connector.
Removing and replacing a FRU 3 5 4 4 When installing: 1. Make sure that the keyboard connector is attached firmly. Then lock the connector. 2. Make sure that the front side of the keyboard is under the frame.
Removing and replacing a FRU 1160 Function board For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1130 Cover, strip (E cover)” on page 63 v “1150 Keyboard” on page 65 1 1 3 2 2 For MT 0689 and 0768 Step Screw (quantity) Color Torque 1 M2.5 × 3 mm, flat-head, nylon-coated (2) Black 0.392 Nm (4 kgfcm) For MT 0769 68 Step Screw (quantity) Color Torque 1 M2.5 × 3 mm, pan-head, nylon-coated (2) Black 0.
Removing and replacing a FRU 1170 LCD unit For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover” on page 47 v “1040 PCI Express Mini Card for 802.11 a/b/g wireless LAN” on page 49 v “1050 PCI Express Mini Card for 802.
Removing and replacing a FRU For MT 0768 and 0769 Note: Step 1a is only for MT 0769. 1a 1 For MT 0768 Step Screw (quantity) Color Torque 1 M2.5 × 6 mm, flat-head, nylon-coated (1) Silver 0.392 Nm (4 kgfcm) For MT 0769 Step Screw (quantity) Color Torque 1 M2.5 × 6 mm, pan-head, nylon-coated (1) Silver 0.392 Nm (4 kgfcm) When installing: Make sure that the connector is attached firmly.
Removing and replacing a FRU Pull out the wireless LAN antenna cables from the guide hole of the system board 2 , and release them from the cable guides of the frame 3 . For MT 0689 and 0768 5 6 4 3 2 When installing: Make sure that the connectors 4 , 5 , and 6 are attached firmly.
Removing and replacing a FRU For MT 0769 Pull out the wireless LAN antenna cables from the guide hole of the system board 2 , and release them from the cable guides of the frame 3 . Pull out the LCD cable from the hole of the system board 6 . 5 6 4 3 2 2 When installing: Make sure that the connectors 4 and 5 are attached firmly.
Removing and replacing a FRU For MT 0689 7 7 8 8 Step Screw (quantity) Color Torque 7 M2.5 × 8 mm, flat-head, nylon-coated (2) Silver 0.392 Nm (4 kgfcm) When installing: Route the antenna cables along the cable guides. When you route the cables, do not tense them. To do so, the cables may get damaged by the cable guides of the frame, and may cause a broken wire. Make sure that you do not pinch the antenna cables when you attach the LCD assembly.
Removing and replacing a FRU For MT 0768 and 0769 7 7 8 8 For MT 0768 Step Screw (quantity) Color Torque 7 M2.5 × 6 mm, flat-head, nylon-coated (4) Silver 0.392 Nm (4 kgfcm) For MT 0769 Step Screw (quantity) Color Torque 7 M2.5 × 6 mm, pan-head, nylon-coated (4) Silver 0.392 Nm (4 kgfcm) When installing: Route the antenna cables along the cable guides. When you route the cables, do not tense them.
Removing and replacing a FRU 1180 Top cover assembly (C cover) with speakers and Bluetooth daughter card (BDC) for MT 0689 and 0768 For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover” on page 47 v “1040 PCI Express Mini Card for 802.11 a/b/g wireless LAN” on page 49 v “1050 PCI Express Mini Card for 802.
Removing and replacing a FRU Note: Step 3a is only for MT 0689. 3a 3a Step Screw (quantity) Color Torque 3a M2.5 × 6 mm, flat-head, nylon-coated (2) Black 0.392 Nm (4 kgfcm) For MT 0768 Note: Step 1b is only for MT 0768 1b Step Screw (quantity) Color Torque 1b M2.5 × 6 mm, flat-head, nylon-coated (1) Black 0.
Removing and replacing a FRU Note: Steps 2b and 3b are only for MT 0768. 2b 2b 2b 2b 2b 2b 2b 2b 2b 2b Step Screw (quantity) Color Torque 2b M2.5 × 6 mm, flat-head, nylon-coated (17) Black 0.392 Nm (4 kgfcm) 3b Step Screw (quantity) Color Torque 3b M2.5 × 6 mm, flat-head, nylon-coated (2) Black 0.
Removing and replacing a FRU 4 When installing: Make sure that the connectors are attached firmly.
Removing and replacing a FRU The Bluetooth daughter card is attached underside of the top cover assembly. To remove the Bluetooth daughter card, do as follows: 1 1 2 Step Screw (quantity) Color Torque 1 M2 × 4 mm, flat-head, nylon-coated (2) Black 0.245 Nm (2.5 kgfcm) When installing: Make sure that the connector is attached firmly.
Removing and replacing a FRU 1190 Top cover assembly (C cover) for MT 0769 For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover” on page 47 v “1040 PCI Express Mini Card for 802.11 a/b/g wireless LAN” on page 49 v “1050 PCI Express Mini Card for 802.
Removing and replacing a FRU 2 2 2 2 2 2 3 2 2 2 2 Step Screw (quantity) Color Torque 2 M2.5 × 8 mm, pan-head, nylon-coated (16) Silver 0.392 Nm (4 kgfcm) 3 M2.5 × 10 mm, pan-head, nylon-coated (1) Silver 0.392 Nm (4 kgfcm) 4 Step Screw (quantity) Color Torque 4 M2.5 × 3 mm, pan-head, nylon-coated (2) Black 0.
Removing and replacing a FRU 5 When installing: Make sure that the connectors are attached firmly.
Removing and replacing a FRU 1200 USB/Audio connector card For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover” on page 47 v “1040 PCI Express Mini Card for 802.11 a/b/g wireless LAN” on page 49 v “1050 PCI Express Mini Card for 802.
Removing and replacing a FRU 1210 VGA connector card For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover” on page 47 v “1040 PCI Express Mini Card for 802.11 a/b/g wireless LAN” on page 49 v “1050 PCI Express Mini Card for 802.
Removing and replacing a FRU For MT 0769 1 3 2 Step Screw (quantity) Color Torque 1 M2.5 × 4 mm, pan-head, nylon-coated (1) Silver 0.392 Nm (4 kgfcm) When installing: Make sure that the connector is attached firmly.
Removing and replacing a FRU 1220 System board, MDC, PC Card slot, and bottom cover assembly (D cover) for MT 0689 and 0768 For access, remove these FRUs, in order: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover” on page 47 v “1030 Hard disk drive” on page 48 v “1040 PCI Express Mini Card for 802.11 a/b/g wireless LAN” on page 49 v “1050 PCI Express Mini Card for 802.
Removing and replacing a FRU 3 2 Step Screw (quantity) Color Torque 2 M2.5 × 3 mm, flat-head, nylon-coated (1) Black 0.392 Nm (4 kgfcm) In step 3 , remove the system board, the MDC, and the PC Card slot together from the bottom cover. To remove the MDC, do as follows: 1 1 2 Step Screw (quantity) Color Torque 1 M2.5 × 3 mm, flat-head, nylon-coated (2) Silver 0.
Removing and replacing a FRU To remove the PC Card slot assembly, do as follows: 1 1 1 1 2 Step Screw (quantity) Color Torque 1 M2 × 4 mm, flat-head, nylon-coated (4) Silver 0.245 Nm (2.5 kgfcm) When installing: Make sure that the connectors of PC Card slot assembly is attached to the system board firmly, and then fasten the screws.
Removing and replacing a FRU Note: Applying labels to the bottom cover When you replace the base cover, you need to stick some labels on the new base cover. Some of the labels have been shipped with the new base cover, and some may need to be reused from the old base cover. Following labels are the typical labels stuck on the bottom side of the computer when it is shipped. a MAC label (802.11 a/b/g) b Product label c Windows license label (COA) d MAC label (802.
Removing and replacing a FRU 1230 System board, MDC, ExpressCard slot, heat sink assembly, and bottom cover assembly (D cover) for MT 0769 For access, remove these FRUs, in order: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover” on page 47 v “1030 Hard disk drive” on page 48 v “1040 PCI Express Mini Card for 802.11 a/b/g wireless LAN” on page 49 v “1050 PCI Express Mini Card for 802.
Removing and replacing a FRU 2 4 2 3 3 Step Screw (quantity) Color Torque 2 M2.5 × 4 mm, pan-head, nylon-coated (2) Silver 0.392 Nm (4 kgfcm) When installing: Make sure that the connectors are attached firmly.
Removing and replacing a FRU 5 In step 5 , remove the system board, the MDC, the ExpressCard slot and the heat sink assembly together from the bottom cover. To remove the MDC, do as follows: 1 1 2 Step Screw (quantity) Color Torque 1 M2.5 × 3 mm, pan-head, nylon-coated (2) Silver 0.
Removing and replacing a FRU To remove the ExpressCard slot, do as follows: 1 1 Step Screw (quantity) Color Torque 1 M2 × 4 mm, pan-head, nylon-coated (2) Black 0.245 Nm (2.5 kgfcm) 2 When installing: Make sure that the connectors of ExpressCard slot is attached to the system board firmly, and then fasten the screws.
Removing and replacing a FRU To remove the heat sink assembly, do as follows: For discrete models 2 3 1 1 Step Screw (quantity) Color Torque 1 Thermal screw, nylon-coated (4) Silver 0.392 Nm (4 kgfcm) 2 M2.5 × 3 mm, pan-head, nylon-coated (1) Silver 0.392 Nm (4 kgfcm) For integrated models 2 1 Step Screw (quantity) Color Torque 1 M2.5 × 3 mm, pan-head, nylon-coated (1) Silver 0.
Removing and replacing a FRU Note: Applying labels to the bottom cover When you replace the base cover, you need to stick some labels on the new base cover. Some of the labels have been shipped with the new base cover, and some may need to be reused from the old base cover. Following labels are the typical labels stuck on the bottom side of the computer when it is shipped. a MAC label (802.11 a/b/g) b Product label c Windows license label (COA) d MAC label (802.
Removing and replacing a FRU 2010 LCD front bezel (B cover) For access, remove this FRU: v “1010 Battery pack” on page 46 For MT 0698 and 0768 1a 1b 1a 1b Note: Screws 1a are only for MT0768. Step Screw cap Screw (quantity) Color Torque 1a M2.5 × 5 mm, flat-head, nylon-coated (2) Black 0.392 Nm (4 kgfcm) 1b M2.5 × 5 mm, flat-head, nylon-coated (2) Black 0.392 Nm (4 kgfcm) For MT 0769 1a 1a 1a 1a 1b 1b Step Screw cap 1a Screw (quantity) Color Torque M2.
Removing and replacing a FRU In step 2 , while sliding the LCD latch lever in the direction shown by the arrow, remove the bezel in the direction shown by arrow 3 .
Removing and replacing a FRU 2020 Inverter card For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “2010 LCD front bezel (B cover)” on page 96 1 3 4 2 For MT 0698 and 0768 Step Screw (quantity) Color Torque 1 M2.5 × 5 mm, flat-head, nylon-coated (1) Black 0.392 Nm (4 kgfcm) For MT 0769 Step Screw (quantity) Color Torque 1 M2 × 3 mm, pan-head, nylon-coated (1) Silver 0.245 Nm (2.
Removing and replacing a FRU 2030 LCD panel, LCD cable, and hinges For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover” on page 47 v “1040 PCI Express Mini Card for 802.11 a/b/g wireless LAN” on page 49 v “1050 PCI Express Mini Card for 802.
Removing and replacing a FRU For MT 0769 1 2 1 Step Screw (quantity) Color Torque 1 M2.5 × 5 mm, pan-head, nylon-coated (2) Black 0.
Removing and replacing a FRU Remove the hinges ( a ) from the LCD panel. a 4 3a 3b 3a a 4 3a 3b 3a Note: Screws 3b are only for MT 0768 and 0769. For MT 0689 and 0768 Step Screw (quantity) Color Torque 3a M2 × 3 mm, flat-head, nylon-coated (4) Silver 0.245 Nm (2.5 kgfcm) 3b M2 × 3 mm, flat-head, nylon-coated (4) Silver 0.245 Nm (2.5 kgfcm) For MT 0769 Step Screw (quantity) Color Torque 3a M2 × 3 mm, pan-head, nylon-coated (4) Silver 0.245 Nm (2.
Removing and replacing a FRU 2040 Camera and LCD rear cover assembly (A cover) For access, remove these FRUs in order: v “1010 Battery pack” on page 46 v “1020 Hard disk drive slot cover” on page 47 v “1040 PCI Express Mini Card for 802.11 a/b/g wireless LAN” on page 49 v “1050 PCI Express Mini Card for 802.
Removing and replacing a FRU For MT 0768 and 0769 1 Lenovo 3000 N100 and N200 103
Locations Locations Front view 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Lenovo Care button Volume control buttons Built-in stereo speaker (right)*1 Keyboard Fingerprint reader (for some models) Touch pad Touch pad buttons System and power status indicators Note: For the description of each indicator, see “Status indicators” on page 33.
Locations Rear view 1 2 3 4 5 6 7 8 RJ-11 (modem) connector AC power connector S-Video connector External monitor connector Optical drive USB connectors Microphone jack Stereo headphone jack 1 2 8 7 6 5 4 3 Bottom view 1 2 3 4 5 6 7 8 Battery pack latch Battery pack Battery pack latch Memory card slot Thermal module slot Wireless radio switch Hard disk drive slot LCD cover latch 2 4 3 5 1 6 7 8 Lenovo 3000 N100 and N200 105
Parts list Parts list v Each FRU is available for all types or models, unless specific types or models are specified. v FRU with specific models listed and described as xxU (where U is an example of a country designator) should be used for all models ending in U. v FRU with specific models listed and described as 3Dx (where 3D is an example of a unique configuration) should be used for all of these models, unless specific country or region designator is specified.
Parts list Overall 1 2 3 4 5 24 6 7 23 8 22 21 c 9 b a 10 20 11 12 19 13 14 18 17 16 15 Lenovo 3000 N100 and N200 107
Parts list No. FRU FRU no. RoHS ID CRU ID a - c See “Miscellaneous parts” on page 152. 1 LCD unit (see “LCD FRUs” on page 129.) 2 Cover, strip (E cover) for MT 0689 and 0768 41W2115 R N Cover, strip for MT 0769 41R7807 R N 3 Keyboard (see “Keyboard” on page 136.
Parts list No. 5 FRU FRU no.
Parts list No. 6 FRU FRU no.
Parts list No. FRU FRU no.
Parts list No. FRU FRU no. RoHS CRU ID ID 6 System board assembly, 15W discrete • 0769-CZx, A8x, A9x, Adx, B2x, B3x, G2x, G6x, Acx, D2x, CVx, CWx, CXx, D4x, G3x. D5x, D9x, DBx, DCx, DDx, B4x, DHx, B6x, B7x, BEx, BFx, BNx, BPx, BQx, BRx, BSx, BWx, BXx, BZx, E4x, E5x, E9x, Eex, L7x, K6x, K7x, L4x, K8x, ETx, EMx, ENx, EQx, EHx, Ejx, Ewx, EXx, 41R7695 R D System board assembly, 15W discrete support CPU celeron 540 • 0769-CZx, A8x, A9x, Adx, B2x, B3x, G2x, G6x, Acx, D2x, CVx, CWx, CXx, D4x, G3x.
Parts list No. FRU FRU no. RoHS CRU ID ID 8 DVD/CD-RW combo drive assembly, 12.
Parts list No. FRU FRU no. RoHS CRU ID ID 8 DVD-RAM/RW drive assembly, 12.
Parts list No. FRU FRU no.
Parts list No. FRU 12 SATA hard disk drive, 80 GB, 9.
Parts list No. FRU FRU no. 12 SATA hard disk drive, 80 GB, 9.
Parts list No. FRU FRU no. RoHS CRU ID ID 12 SATA hard disk drive, 100 GB, 9.5 mm, 5,400 rpm, 42T1607 Fujitsu • 0689-A5x, A7x, B7x, BCx, C7x, C8x, C9x, CBx, CGx, CHx, CYx, D5x, DBx, DCx, F3x G7x, GBx, GCx, GDx, GEx, GFx • 0768-AHx, B2x, BBx, BDx, BGx, BHx, BJx, BKx, BLx, BSx, C6x, C7x, C8x, C9x, CAx, CBx, CDx, CEx, CGx, CKx, CNx, CVx, DDx, DEx, G2x, G3x, G7x, GAx, GBx, GCx, GDx, GEx R ** SATA hard disk drive, 120 GB, 9.
Parts list No. FRU FRU no.
Parts list No. FRU FRU no. RoHS CRU ID ID 13 Broadcom 802.
Parts list No. FRU FRU no.
Parts list No. FRU FRU no.
Parts list No. FRU FRU no.
Parts list No. FRU FRU no. RoHS CRU ID ID 23 CPU assembly, Intel Celeron M processor 410 (1.46 GHz) • 0689-65x, 66x, 67x, 68x, 69x • 0768-65x, 66x, 67x, 68x, 82x 41W5181 R N CPU assembly, Intel Celeron M processor 420 (1.
Parts list No. FRU FRU no. RoHS CRU ID ID 23 CPU assembly, Intel Core Duo processor T2050 (1.60 GHz) • 0689-85x • 0768-85x 41W1461 R N CPU assembly, Intel Core Duo processor T2060 (1.60 GHz) • 0689-GGx, E2x, E4x • 0768-EGx, EJx, EKx, ELx, GFx, GHx, GJx, GKx, GRx, GSx, GTx 42W7659 R N CPU assembly, Intel Core Duo processor T2250 (1.73 GHz) • 0689-GNx, GRx • 0768-BQx, BTx, FGx 41W1463 R N CPU assembly, Intel Core Duo processor T2300 (1.
Parts list No. FRU FRU no. RoHS CRU ID ID 23 CPU assembly, Intel Core 2 Duo processor T5500 (1.
Parts list No. FRU FRU no. RoHS CRU ID ID 23 CPU assembly, Intel Core Duo Processor T2330 (1.6 GHz) 43N7303 • 0769-ARx, BBx, BCx, BKx, BLx, AUx, AVx, F5x, BUx, BYx, BZx, DNx R D CPU assembly, Intel Core Duo Processor T2310 (1.46 GHz) • 0769-ANx, APx, AQx, BAx, BJx, BRx, AXx, AZx, F7x, DMx 43N7304 R D CPU assembly, Intel Pentium Dual Core processor T2390 (1.
Parts list 128 No.
Parts list LCD FRUs 1 2 7 3 4 6 5 14.1-in. WXGA TFT No. 1 FRU FRU no.
Parts list No. 2 FRU FRU no. RoHS ID CRU ID LCD panel, 14.1-in. WXGA anti-glare v 0689-31x, 33x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Fx, 3Jx, 3Lx, 3Mx, 41x,,42x, 43x, 44x, 52x, 5Jx, 67x, 68x, 69x, 6Ax, 6Hx, 6Jx, 6Lx, 6Mx, 6Px, 6Rx, 6Sx, 6Xx, 6Yx, 73x, 77x, 7Vx, 7Wx, 82x, 83x, 86x, A4x, B2x, B3x, B7x, B8x, CCx, CDx, CHx, CQx Samsung 13N7154 R N AUO 13N7156 R N CMO 13N7158 R N LPL 42T0311 R N LCD panel, 14.1-in.
Parts list 15.4-in. WXGA TFT No. 1 2 FRU FRU no.
Parts list No. FRU FRU no. RoHS ID CRU ID 2 LCD panel, 15.4-in.
Parts list No. 5 6 7 FRU FRU no.
Parts list 15.4-in. WSXGA+ TFT No.
Parts list No. 3 FRU FRU no.
Parts list Keyboard Keyboard for MT 0689 and 0768 136 Language P/N (NMB) P/N RoHS (Chicony) ID CRU ID Arabic 39T7368 39T7432 N Belgian 39T7365 39T7429 Chinese, Traditional 39T7379 39T7443 Czech 39T7373 39T7437 Danish 39T7362 39T7426 Dutch 39T7359 39T7423 English, U.K. 39T7357 39T7421 English, U.S. 39T7353 39T7417 English, U.S.
Parts list Keyboard for MT 0769 Language P/N (NMB) P/N RoHS (Chicony) ID CRU ID Arabic 42T3353 42T3418 N Belgian 42T3350 42T3415 Chinese, Traditional 42T3364 42T3429 Czech 42T3358 42T3423 Danish 42T3347 42T3412 Dutch 42T3344 42T3409 English, U.K. 42T3342 42T3407 English, U.S. 42T3338 42T3403 English, U.S.
Parts list Recovery discs Windows XP Professional CDs Windows XP Professional is preinstalled as the operating system in the following models: v 0689-22x, 26x, 27x, 29x, 2Bx, 2Jx, 2Px, 33x, 34x, 36x, 38x, 3Ax, 3Dx, 3Hx, 41x, 43x, 44x, 5Dx, 5Fx, 5Hx, 6Ax, 6Cx, 6Ex, 6Fx, 6Gx, 6Hx, 6Jx, 6Kx, 6Lx, 6Vx, 6Wx, 7Nx, 7Qx, 7Sx, 86x, K2x, A4x, A6x, A7x, A9x, ABx, ACx, ADx, AEx, AFx, AGx, AJx, B3x, B5x, B6x, B7x, B8x, B9x, BCx, C5x, C9x, CDx, CFx, CGx, CHx, CKx, CMx, CPx, CWx, CXx, CYx, D9x, DCx v 0768-21x, 22x, 26x,
Parts list · 0769‐AHx, AKx, D8x Language P/N RoHS ID CRU ID Arabic 44Y1149 R * Chinese, Simplified N/A Chinese, Traditional 44Y1143 Chinese, Traditional (Hong Kong S.A.R.) 44Y1144 Czech 44Y1148 Danish 44Y1138 Dutch 44Y1141 English, U.K. with disabled modem and WLAN 44Y1131 English, U.S.
Parts list Windows XP Home Edition CDs Windows XP Home Edition is preinstalled as the operating system in the following models: v 0689-24x, 25x, 28x, 2Ax, 2Ex, 2Fx, 2Hx, 2Kx, 2Lx, 2Mx, 2Nx, 2Qx, 2Rx, 2Sx, 31x, 37x, 39x, 3Bx, 3Cx, 3Fx, 3Gx, 3Jx, 3Kx, 42x, 52x, 54x, 55x, 56x, 57x, 59x, 5Ax, 5Bx, 5Cx, 5Gx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 66x, 67x, 68x, 69x, 6Bx, 6Dx, 6Mx, 6Nx, 6Px, 6Qx, 6Rx, 6Sx, 6Tx, 6Ux, 72x, 75x, 76x, 77x, 7Mx, 7Px, 7Rx, 7Tx, 7Ux, 85x, A5x, A8x, AAx, AHx, B2x, B4x, BAx, BBx, BEx, C3x, C7x, CBx, C
Parts list 140 Language P/N RoHS ID CRU ID Arabic 43T4481 R * Chinese, Simplified 43T4474 Chinese, Traditional 43T4475 Chinese, Traditional (Hong Kong S.A.R.) 43T4476 Czech 43T4480 Danish 43T4470 Dutch 43T4473 English, (UD) U.K. with disabled modem and WLAN 43T4463 English, U.S., U.K.
Parts list Windows Vista Home Premium (32 bit) DVDs for MT 0689 and 0768 Windows Vista Home Premium is preinstalled as the operating system in the following models: v 0689-E3x, F5x, GAx, GBx, GCx, GDx, GFx, GHx, GKx v 0768-E2x, E5x, ECx, EGx, EJx, F9x, GAx, GBx, GCx, GDx, GEx, GGx Language P/N RoHS ID CRU ID Chinese, Simplified 43T7686 R * Chinese, Traditional 43T7687 Chinese, Traditional (Hong Kong S.A.R.) 43T7688 Czech 43T7679 Danish 43T7677 Dutch 43T7678 English, (UD) U.K.
Parts list Windows Vista Home Premium (32 bit) DVDs for MT 0769 Windows Vista Home Premium is preinstalled as the operating system in the following models: v 0769-AAx, ACx, ADx, B3x, C4x, C7x, C9x, CAx, CZx, D4x, D5x, G3x 142 Language P/N RoHS ID CRU ID Brazilian Portuguese 44X9739 R * Bulgarian 44X9760 Chinese, Traditional 44X9754 Chinese, Traditional (Hong Kong S.A.R.) 44X9755 Croatian 44X9761 Czech 44X9746 Danish 44X9744 Dutch 44X9745 English, (UD) U.K.
Parts list Windows Vista Home Basic (32 bit) DVDs for MT 0689 and 0768 Windows Vista Home Basic is preinstalled as the operating system in the following models: v 0689-EAx, F2x, F3x, F8x, G3x, G8x, G9x, GGx, GLx, GTx, GUx v 0768-EHx, F3x, F4x, F7x, FBx, FDx, FEx, FGx, FJx, G2x, G8x, GFx, GHx, GKx, GQx, GRx, GTx Language P/N RoHS ID CRU ID Chinese, Simplified 43T7634 R * Chinese, Traditional 43T7635 Chinese, Traditional (Hong Kong S.A.R.
Parts list Windows Vista Home Basic (32 bit) DVDs for MT 0769 Windows Vista Home Basic is preinstalled as the operating system in the following models: v 0769-C8x, CBx, CEx, CGx, CJx, CLx, CNx, CQx, CUx, CXx, CYx, D2x, D6x, G5x 144 Language P/N RoHS ID CRU ID Brazilian Portuguese 44X9804 R * Chinese, Traditional 44X9819 Chinese, Traditional (Hong Kong S.A.R.) 44X9820 Czech 44X9811 Danish 44X9809 Dutch 44X9810 English, (UD) U.K. with disabled modem and WLAN 44X9800 English, U.S., U.K.
Parts list Windows Vista Business (32 bit) DVDs for MT 0689 and 0768 Windows Vista Business is preinstalled as the operating system in the following models: v 0689-E2x, E4x, E5x, F4x, F7x, G4x, G7x, GEx, GNx, GPx, GQx, GSx v 0768-E6x, E7x, ELx, F2x, F6x, FFx, FHx, G3x, G5x, G6x, G7x, GJx, GLx, GMx, GNx, GPx, GSx, GUx, GVx, GWx, GXx Language P/N RoHS ID CRU ID Arabic 43T7575 R * Chinese, Simplified 43T7581 Chinese, Traditional 43T7582 Chinese, Traditional (Hong Kong S.A.R.
Parts list Windows Vista Business (32 bit) DVDs for MT 0769 Windows Vista Business is preinstalled as the operating system in the following models: v 0769-A7x, A8x, ABx, B2x, C3x, C5x, C6x, CDx, CFx, CHx, CKx, CMx, CPx, CRx, CVx, CWx, D3x, D7x, G6x 146 Language P/N RoHS ID CRU ID Brazilian Portuguese 44X9772 R * Bulgarian 44X9792 Chinese, Traditional 44X9787 Chinese, Traditional (Hong Kong S.A.R.) 44X9788 Croatian 44X9793 Czech 44X9779 Danish 44X9777 Dutch 44X9778 English, (UD) U.K.
Parts list Windows Vista Business (64 bit) DVDs Windows Vista Business is preinstalled as the operating system in the following models: v 0769-G4x Language P/N RoHS ID CRU ID Brazilian Portuguese 44X9855 R * Chinese, Traditional 44X9870 Chinese, Traditional (Hong Kong S.A.R.) 44X9871 Czech 44X9862 Danish 44X9860 Dutch 44X9861 English, (UD) U.K. with disabled modem and WLAN 44X9851 English, U.S., U.K.
Parts list Windows Vista Ultimate (32 bit) DVDs Windows Vista Ultimate is preinstalled as the operating system in the following models: v 0769-A9x, B4x, G2x 148 Language P/N RoHS ID CRU ID Brazilian Portuguese 44X9830 R * Chinese, Traditional 44X9845 Chinese, Traditional (Hong Kong S.A.R.) 44X9846 Czech 44X9837 Danish 44X9835 Dutch 44X9836 English, (UD) U.K. with disabled modem and WLAN 44X9826 English, U.S., U.K.
Parts list Corel software CDs Language P/N RoHS ID CRU ID English, U.S.
Parts list Power cords Power cords for MT 0689 and 0768 A Lenovo 3000 power cord for a specific country or region is usually available only in that country or region: For 2-pin power cords: Region P/N RoHS ID CRU ID Canada, U.S.
Parts list Power cords for MT 0769 A Lenovo 3000 power cord for a specific country or region is usually available only in that country or region: For 2-pin power cords: Region P/N (Longwell) P/N (Volex) RoHS ID CRU ID Argentina 42T5020 42T5105 * Brazil 42T5026 42T5111 Canada, U.S. 42T5008 42T5093 Japan 42T5014 42T5099 Region P/N (Longwell) P/N (Volex) RoHS ID CRU ID Australia, New Zealand 42T5050 42T5135 * Denmark 42T5041 42T5126 Europe 42T5029 42T5114 Hong Kong S.A.R.
Parts list Miscellaneous parts 152 FRU P/N RoHS ID CRU ID Screw kit for MT 0689 (including nylon-coated screws): v M2 × 3 mm (silver), flat head (9) v M2 × 4 mm (black), flat head (6) v M2 × 5 mm (silver), flat head (10) v M2.5 × 3 mm (black), flat head (18) v M2.5 × 4 mm (silver), flat head (10) v M2.5 × 5 mm (black), flat head (7) v M2.
Parts list FRU P/N RoHS ID CRU ID Bottom miscellaneous parts for MT 0769: v RJ11 cable v Bluetooth cable v USB cable v TV-out cable v Speakers v USB EMI tape v Blank bezel for ExpressCard slot v Rubber foot, front (2) v Rubber foot, rear (2) 41R7793 R N LCD miscellaneous parts for MT 0689: v LCD rubber, upper (4) v LCD rubber, middle (2) v LCD rubber, lower (2) v LCD latch hook L v LCD latch hook R v LCD spring v LCD knob v LCD latch wire v Camera cable 41W5215 R N LCD miscellaneous parts for MT
Parts list Common parts list Tools Tool P/N Triconnector wrap plug 72X8546 Audio wrap cable 66G5180 USB parallel test cable 05K2580 Screwdriver kit 95F3598 Mini PC tool set 00P7033 1/4" drive spinner handle 1650840 1/4" Sq.
Notices Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Notices estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Trademarks Lenovo 3000 N100 and N200 157
Part Number: 42X3553 (1P) P/N: 42X3553
