E590, R590 and E595 User Guide
Read this first Before using this documentation and the product it supports, ensure that you read and understand the following: • Appendix A “Important safety information” on page 65 • Safety and Warranty Guide • Setup Guide Second Edition (April 2019) © Copyright Lenovo 2018, 2019. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant to a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No.
Contents About this documentation . . . . . . . . iii Chapter 1. Meet your computer . . . . . 1 Front . . . . . . . . . . . . . Base (ThinkPad E590 and R590) . . Base (ThinkPad E595) . . . . . . Left . . . . . . . . . . . . . Right . . . . . . . . . . . . . Features and specifications . . . . Statement on USB transfer rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 3 4 6 7 8 Chapter 2. Get started with your computer . . . . . . . . . . .
Appendix A. Important safety information . . . . . . . . . . . . . . . 65 Appendix C. Compliance information . . . . . . . . . . . . . . . 83 Appendix B. Accessibility and ergonomic information . . . . . . . . 79 Appendix D. Notices and trademarks . . . . . . . . . . . . . . .
About this documentation • Illustrations in this documentation might look different from your product. • Depending on the model, some optional accessories, features, and software programs might not be available on your computer. • Depending on the version of operating systems, some user interface instructions might not be applicable to your computer. • Documentation content is subject to change without notice.
iv E590, R590 and E595 User Guide
Chapter 1. Meet your computer Front 1. Microphones Capture or record sound. Take pictures or record videos by clicking Camera from the Start menu. The camera indicator nearby is on when in use. 2. Camera 3. Screen © Copyright Lenovo 2018, 2019 If you use other apps that support photographing, video chatting, and video conference, the camera starts automatically when you enable the camerarequired feature from the app.
Base (ThinkPad E590 and R590) Press to turn on the computer or put the computer to sleep mode. To turn off the computer, open the Start menu, click Shut down. Power, and then select The indicator in the power button shows the system status of your computer. 1. Power button • Blinking for three times: The computer is initially connected to power. • On: The computer is on. • Off: The computer is off or in hibernation mode. • Blinking rapidly: The computer is entering sleep or hibernation mode.
Base (ThinkPad E595) Press to turn on the computer or put the computer to sleep mode. To turn off the computer, open the Start menu, click Shut down. Power, and then select The indicator in the power button shows the system status of your computer. 1. Power button • Blinking for three times: The computer is initially connected to power. • On: The computer is on. • Off: The computer is off or in hibernation mode. • Blinking rapidly: The computer is entering sleep or hibernation mode.
Left 1. USB-C™ connector / power connector • Charge your computer. • Charge USB-C compatible devices with the output voltage and current of 5 V and 3 A. • Transfer data at USB 3.1 speed, up to 5 Gbps. • Connect to an external display: – USB-C to VGA: 1920 x 1080 pixels, 60 Hz – USB-C to DP: 3840 x 2160 pixels, 60 Hz • Connect to USB-C accessories to help expand your computer functionality. To purchase USB-C accessories, go to https://www.lenovo.com/accessories.
4. USB 3.1 connector Gen 1 Connect USB-compatible devices, such as a USB keyboard, USB mouse, USB storage device, or USB printer. 5. Audio connector Connect headphones or a headset with a 3.5-mm (0.14-inch) and 4-pole plug to listen to the sound from the computer. Note: The conventional microphone is not supported. Chapter 1.
Right 1. microSD card slot Insert a microSD card for data access or storage. See “Use a microSD card” on page 23. 2. USB 2.0 connector Connect a USB-compatible device, such as a USB keyboard, USB mouse, USB storage device, or USB printer. 3. Ethernet connector Connect to a local area network (LAN). When the green indicator is on, the computer is connected to a LAN. When the yellow indicator blinks, data is being transmitted. 4.
Features and specifications • Width: 369 mm (14.5 inches) Dimensions • Depth: 252.5 mm (9.94 inches) • Thickness: 20.7 mm (0.81 inches) Maximum heat output (depending on the model) • 45 W (154 Btu/hr) Power source (ac power adapter) • Sine-wave input at 50 Hz to 60 Hz • 65 W (222 Btu/hr) • Input rating of the ac power adapter: 100 V to 240 V ac, 50 Hz to 60 Hz Microprocessor To view the microprocessor information of your computer, right-click the Start button and then click System.
• Always On USB 3.1 connector Gen 1 • Audio connector • Ethernet connector Connectors and slots • HDMI connector • microSD card slot • USB-C connector • USB 2.0 connector • USB 3.
Chapter 2. Get started with your computer Get started with Windows 10 Learn the basics of Windows 10 and start working with it right away. For more information about Windows 10, see the Windows help information. Windows account To use the Windows operating system, a user account is required. It can either be a Windows user account or a Microsoft account. Windows user account When you start Windows for the first time, you are prompted to create a Windows user account.
Windows user interface 1. Account Change account settings, lock the computer, or sign out from the current account. 2. Settings Launch Settings. 3. Power Shut down, restart, or put the computer into sleep. 4. Start button Open the Start menu. 5. Windows Search Type what you are looking for in the search box and get search results from your computer and the Web. 6. Task View Display all opened apps and switch among them. 7.
Launch an app • Open the Start menu and select the app you want to launch. • Use Windows Search. Windows label Your computer might have a Windows 10 Genuine Microsoft label affixed to its cover depending on the following factors: • Your geographic location • Edition of Windows 10 that is preinstalled Go to https://www.microsoft.com/en-us/howtotell/Hardware.aspx for illustrations of the various types of Genuine Microsoft labels.
Use Lenovo Vantage The preinstalled Lenovo Vantage is a customized one-stop solution to help you maintain your computer with automated updates and fixes, configure hardware settings, and get personalized support. Access Lenovo Vantage Open the Start menu and click Lenovo Vantage. You also can type Lenovo Vantage in the search box. To download the latest version of Lenovo Vantage, go to Microsoft Store and search by the app name.
Interact with your computer Your computer provides you various ways to navigate the screen. Use the keyboard shortcuts The special keys on the keyboard help you work more easily and effectively. 1. Numeric keypad Input numbers quickly when the Numeric Lock indicator is on. Open the Start menu. 2. Windows logo key For information about using this key with other keys, see the Windows help information. Switch the letter case between the upper case and lower case. 3.
Mute or unmute the speakers. When the key indicator is on, the speakers are muted. If you mute the speakers and turn off your computer, the speakers remain muted when you turn on your computer. Decrease the speaker volume. Increase the speaker volume. Mute or unmute the microphones. When the key indicator is on, the microphones are muted. Darken the computer display. Brighten the computer display. Manage external displays. Enable or disable the built-in wireless features. Open the Settings window.
Fn+4 Put the computer to sleep mode. To wake up the computer, press Fn or the power button. Fn+Left arrow key Equal the Home key. Fn+Right arrow key Equal the End key. Use the TrackPoint pointing device The TrackPoint pointing device enables you to perform all the functions of a traditional mouse, such as pointing, clicking, and scrolling. Use the TrackPoint pointing device 1.
Replace the pointing-stick nonslip cap Note: Ensure that the new cap has grooves a . Use the trackpad The entire trackpad surface is sensitive to finger touch and movement. You can use the trackpad to perform all the pointing, clicking, and scrolling functions of a traditional mouse. Use the trackpad 1. Left-click zone Press to select or open an item. You also can tap anywhere on the surface of the trackpad with one finger to perform the left-click action. 2.
Use the touch gestures Tap Two-finger tap Tap anywhere on the trackpad with one finger to select or open an item. Tap anywhere on the trackpad with two fingers to display a shortcut menu. Two-finger scroll Two-finger zoom out Put two fingers on the trackpad and move them in the vertical or horizontal direction. This action enables you to scroll through the document, Web site, or apps. Put two fingers on the trackpad and move them closer together to zoom out.
Use audio To enhance your listening experience, connect speakers, headphones, or a headset with a 3.5-mm (0.14inch), 4-pole plug to the audio connector. Adjust the speaker volume Press to increase the speaker volume or press to decrease the speaker volume. Change the sound settings 1. Go to Control Panel and view by category. 2. Click Hardware and Sound ➙ Sound. 3. Change the settings as you prefer. Use the camera You can use the built-in camera to take photos or record videos.
Table 1. ThinkPad E590 and R590 Connect the external display to Supported resolution the USB-C connector Up to 4096 x 2304 pixels / 60 Hz the HDMI connector Up to 4096 x 2160 pixels / 24 Hz Table 2.
20 E590, R590 and E595 User Guide
Chapter 3. Explore your computer Manage power Use the information in this section to achieve the best balance between performance and power efficiency. Check the battery status The battery status icon or is in the Windows notification area. You can check the battery status, view the current power plan, and access battery settings quickly. Click the battery status icon to display the percentage of battery power remaining and change the power mode. A warning message is displayed when the battery is low.
• If one computer is off, in sleep mode, or hibernation mode, enable the Always On USB feature in UEFI BIOS in the computer. To enable the Always On USB feature, do the following: 1. Enter the UEFI BIOS menu. See “Enter the UEFI BIOS menu” on page 29. 2. Click Config ➙ USB ➙ Always On USB to enable the Always On USB feature. Check the battery temperature 1. Open the Start menu and click Lenovo Vantage. 2. Click Hardware Settings ➙ Power. 3.
Connect to a Bluetooth-enabled device You can connect all types of Bluetooth-enabled device to your computer, such as a keyboard, a mouse, a smartphone, or speakers. The devices must be within a short distance, usually 10 meters (33 feet), from the computer. 1. Turn on Bluetooth on the computer. • Press or . • Open the Start menu, and then click Settings ➙ Devices ➙ Bluetooth & other devices. Turn on the Bluetooth switch. 2. Click Add Bluetooth or other device ➙ Bluetooth. 3.
2. Click Settings ➙ Network & Internet ➙ Airplane mode. 3. Turn on or turn off the Airplane mode switch. Purchase options Lenovo has a number of hardware accessories and upgrades to help expand the capabilities of your computer. Options include memory modules, storage devices, network cards, port replicators or docking stations, batteries, power adapters, keyboards, mice, and more. To shop at Lenovo, go to https://www.lenovo.com/accessories.
Chapter 4. Secure your computer and information Lock the computer Lock your computer to a desk, table, or other fixtures through a compatible security cable lock. Notes: • You are responsible for evaluating, selecting, and implementing the locking device and security feature. Lenovo makes no comments, judgments, or warranties about the function, quality, or performance of the locking device and security feature. Cable locks for your product are available from Lenovo at https:// www.lenovoquickpick.com/.
Supervisor password The supervisor password protects the system information stored in UEFI BIOS. When entering the UEFI BIOS menu, enter the correct supervisor password when you are prompted by the icon . You also can press Enter to skip the password prompt. However, you cannot change most of the system configuration options in UEFI BIOS. If you have set both the supervisor password and power-on password, you can use the supervisor password to access your computer when you turn it on.
• If you forget your power-on password, contact a Lenovo authorized service provider to have the power-on password removed. • If you forget your user hard disk password or both user and master hard disk passwords, Lenovo cannot reset your passwords or recover data from the storage drive. You can contact a Lenovo authorized service provider to have the storage drive replaced. A fee will be charged for parts and service.
28 E590, R590 and E595 User Guide
Chapter 5. Configure advanced settings This chapter provides information about UEFI BIOS, RAID, recovery, operating system installation, and system management. UEFI BIOS This section introduces what is UEFI BIOS and the operations you can perform in UEFI BIOS. What is UEFI BIOS UEFI BIOS is the first program that the computer runs when the computer is turned on. UEFI BIOS initializes the hardware components and loads the operating system and other programs.
4. Press F10 to save the changes and exit. To change the startup sequence temporarily: 1. Restart the computer. When the logo screen is displayed, press F12. 2. Select the device that you want the computer to start from and press Enter. Set the system date and time 1. Restart the computer. When the logo screen is displayed, press F1. 2. Select Date/Time and set the system date and time as desired. 3. Press F10 to save changes and exit.
Note: The items in the graphical user interface (GUI) might change without notice. 1. Open the Start menu, and then click Settings ➙ Update & Security ➙ Recovery. 2. In the Reset this PC section, click Get started. 3. Follow the on-screen instructions to reset your computer. Use advanced options Note: The items in the graphical user interface (GUI) might change without notice. 1. Open the Start menu, and then click Settings ➙ Update & security ➙ Recovery. 2.
5. Click Yes in the User Account Control window to allow the Recovery Media Creator program to start. 6. In the Recovery Drive window, follow the on-screen instructions to create a recovery USB drive. Use the recovery USB drive 1. Ensure that your computer is connected to ac power. 2. Connect the recovery USB drive to the computer. 3. Turn on or restart the computer. When the logo screen is displayed, press F12. The Boot Menu window opens. 4. Select the recovery USB drive as the boot device. 5.
9. Follow the on-screen instructions to install the device drivers and necessary programs. 10. After installing the device drivers, apply Windows Update to get the latest updates, for example the security patches. 11. Go to Microsoft Store to download and install the latest version of Lenovo Vantage. Note: After installing the operating system, do not change the initial UEFI/Legacy Boot setting in the BIOS menu. Otherwise, the operating system will not start correctly.
34 E590, R590 and E595 User Guide
Chapter 6. CRU replacement What are CRUs Customer Replaceable Units (CRUs) are parts that can be upgraded or replaced by the customer. The computers contain the following types of CRUs: • Self-service CRUs: Refer to parts that can be installed or replaced easily by customer themselves or by trained service technicians at an additional cost. • Optional-service CRUs: Refer to parts that can be installed or replaced by customers with a greater skill level.
Disable Fast Startup and the built-in battery Before replacing any CRU, ensure that you disable Fast Startup first and then disable the built-in battery. To disable Fast Startup: 1. Go to Control Panel and view by Large icons or Small icons. 2. Click Power Options, and then click Choose what the power buttons do on the left pane. 3. Click Change settings that are currently unavailable at the top. 4. If prompted by User Account Control (UAC), click Yes. 5.
4. Loosen the screws that secure the base cover assembly 1 , pry up the latches 2 , and then remove the base cover assembly 3 . 5. Install the new base cover assembly in place 1 and ensure that the latches of the base cover assembly are secured in place 2 . Then, tighten the screws 3 . 6. Turn the computer over. Connect the ac power adapter and all disconnected cables to the computer.
Memory module Prerequisite Before you start, read Appendix A “Important safety information” on page 65 and print the following instructions. Attention: Do not touch the contact edge of the memory module. Otherwise the memory module might get damaged. Replacement procedure To replace a memory module, do the following: 1. Disable the built-in battery. See “Disable Fast Startup and the built-in battery” on page 36. 2. Turn off the computer and disconnect the computer from ac power and all connected cables. 3.
6. Install the memory module by doing the following: a. Place the notched end of the new memory module toward the contact edge side of the memory slot. Then insert the new memory module into the memory slot at an angle of about 20 degrees 1 . b. Pivot the memory module downward until it snaps into place 2 . Ensure that the memory module is firmly installed in the memory slot and cannot be moved easily.
5. Detach the connector of the speaker assembly. 6. Remove the speaker assembly. 7. Install the new speaker assembly in place.
8. Attach the connector of the speaker assembly. 9. Reinstall the base cover assembly. 10. Turn the computer over. Connect the ac power adapter and all disconnected cables to the computer. Hard disk drive Prerequisite Before you start, read Appendix A “Important safety information” on page 65 and print the following instructions. Attention: The hard disk drive is sensitive. Inappropriate handling might cause damage and permanent loss of data.
5. Disconnect the hard-disk-drive cable from the system board. Lift the tab and remove the hard disk drive together with its bracket. 6. Detach the cable from the hard disk drive. 7. Detach the bracket from the hard disk drive.
8. Attach the bracket to the new hard disk drive. 9. Connect the cable to the new hard disk drive. 10. Insert the new hard disk drive together with its bracket 1 and then pivot it downward 2 . Ensure that the new hard disk drive is seated in place. Connect the hard-disk-drive cable to the system board. 11. Reinstall the base cover assembly. 12. Turn the computer over. Connect the ac power adapter and all disconnected cables to the computer. M.
Attention: The M.2 solid-state drive is sensitive. Inappropriate handling might cause damage and permanent loss of data. When handling the M.2 solid-state drive, observe the following guidelines: • Replace the M.2 solid-state drive only for upgrade or repair. The M.2 solid-state drive is not designed for frequent changes or replacement. • Before replacing the M.2 solid-state drive, make a backup copy of all the data that you want to keep. • Do not apply pressure to the M.2 solid-state drive.
7. Insert the new M.2 solid-state drive into the slot at an angle of about 20 degrees 1 and pivot the M.2 solid-state drive downward 2 . Then, reinstall the long bracket into place 3 4 , install the screw 5 and tighten the screw 6 . 8. Reinstall the base cover assembly. 9. Turn the computer over. Connect the ac power adapter and all disconnected cables to the computer. 10. If you install a new Intel Optane memory, enable Intel Optane memory by doing the following: a. Restart your computer.
6. Remove the screw 1 and loosen the screw 2 to remove the long bracket 3 . Note: Two thermal pads are attached underneath the long bracket to prevent possible overheating. Ensure that the thermal pads are not removed or damaged.
7. Remove the screw 1 that secures the M.2 solid-state drive. Then, remove the M.2 solid-state drive out of the slot 2 . Note: Remove the short bracket if you want to replace the short M.2 solid-state drive with a long M.2 solid-state drive. Chapter 6.
8. Insert the new M.2 solid-state drive into the slot at an angle of about 20 degrees 1 and pivot the M.2 solid-state drive downward 2 . Install the screw 3 to secure the M.2 solid-state drive. 9. Reinstall the long bracket into place 1 2 . Then, install the screw 3 and tighten the screw 4 . 10. Reinstall the base cover assembly. 11. Turn the computer over. Connect the ac power adapter and all disconnected cables to the computer. 12.
Fingerprint reader Prerequisite Before you start, read Appendix A “Important safety information” on page 65 and print the following instructions. Replacement procedure 1. Disable the built-in battery. See “Disable Fast Startup and the built-in battery” on page 36. 2. Turn off the computer and disconnect the computer from ac power and all connected cables. 3. Close the computer display and turn the computer over. 4. Remove the base cover assembly. See “Base cover assembly” on page 36. 5.
7. Remove the screw that secures the bracket. 8. Remove the bracket 1 and the fingerprint reader 2 .
9. Install the new fingerprint reader 1 and the bracket 2 in place. 10. Install the screw to secure the fingerprint reader. Chapter 6.
11. Install the cable. 12. Attach the connectors. 13. Reinstall the base cover assembly. 14. Turn the computer over. Connect the ac power adapter and all disconnected cables to the computer. Keyboard Prerequisite Before you start, read Appendix A “Important safety information” on page 65 and print the following instructions. Replacement procedure Note: You might be instructed to slide the keyboard frame forward or backward in some of the following steps.
3. Remove the base cover assembly. See “Base cover assembly” on page 36. 4. Remove the screw that secures the keyboard. 5. Turn the computer over and open the display. Take the tool out of the new keyboard package. Insert the tabs a and b into the slot between the TrackPoint buttons and the trackpad 1 . Slightly pivot the tool downward 2 to release the left and right Trackpoint buttons. Then remove the two Trackpoint buttons 3. Chapter 6.
6. Loosen the screws that secure the keyboard. 7. Insert the tabs c and d into the two dents near the two screw heads as shown. 8. Pivot the tool in the direction as shown to release the keyboard 1 . Push the keyboard in the direction as shown by arrows 2 to release the latches from the keyboard bezel.
9. Pivot the keyboard slightly upward as shown by arrow 1 . Then turn the keyboard over as shown by arrow 2 . 10. Put the keyboard on the palm rest as shown and detach the connectors. Then remove the keyboard. 11. Attach the connectors and turn the keyboard over as shown. Chapter 6.
12. Insert the keyboard into the keyboard bezel as shown. Ensure that the front edge of the keyboard (the edge that is close to the display) is under the keyboard bezel. 13. Slide the keyboard in the direction as shown by the arrows. Ensure that the latches are secured under the keyboard frame.
14. Tighten the screws to secure the keyboard. 15. Take the new TrackPoint buttons out of the new keyboard package. Install the TrackPoint buttons as shown. 16. Install the screw to secure the keyboard. 17. Reinstall the base cover assembly. Chapter 6.
18. Connect the ac power adapter and all disconnected cables to the computer.
Chapter 7. Help and support Frequently asked questions How do I access Control Panel? • Open the Start menu and click Windows System ➙ Control Panel. • Use Windows Search. How do I turn off my computer? Open the Start menu and click How do I partition my storage drive? https://support.lenovo.com/solutions/ht503851 Power. Then, click Shut down. 1. Press and hold the power button until the computer turns off. Then, restart the computer. 2.
Error messages If you see a message that is not included in the following table, record the error message first, then shut down the computer and call Lenovo for help. See “Lenovo Customer Support Center” on page 63. Message Solution 0190: Critical low-battery error The computer turned off because the battery power is low. Connect the ac power adapter to the computer and charge the batteries. 0191: System Security - Invalid remote change requested The system configuration change has failed.
Beep errors Lenovo SmartBeep technology enables you to decode beep errors with your smartphone when a black screen occurs with beeps from your computer. To decode the beep error with Lenovo SmartBeep technology: 1. Go to https://support.lenovo.com/smartbeep or scan the following QR Code. 2. Download the proper diagnostic app and install it on your smartphone. 3. Run the diagnostic app and place the smartphone near the computer. 4. Press Fn on your computer to emit the beep again.
Self-help resources Use the following self-help resources to learn more about the computer and troubleshoot problems. Resources How to access? Use Lenovo Vantage to: • Download and install the latest drivers and firmware. • Configure hardware settings. • Open the Start menu and click Lenovo Vantage. • Diagnose computer hardware problems. • Use Windows Search. • Check the computer warranty status. • Protect you computer from malicious Wi-Fi networks.
Call Lenovo If you have tried to correct the problem yourself and still need help, you can call Lenovo Customer Support Center. Before you contact Lenovo Prepare the following before you contact Lenovo: 1. Record the problem symptoms and details: • What is the problem? Is it continuous or intermittent? • Any error message or error code? • What operating system are you using? Which version? • Which software applications were running at the time of the problem? • Can the problem be reproduced? If so, how? 2.
Note: Phone numbers are subject to change without notice. If the number for your country or region is not provided, contact your Lenovo reseller or Lenovo marketing representative. Services available during the warranty period • Problem determination - Trained personnel are available to assist you with determining if you have a hardware problem and deciding what action is necessary to fix the problem.
Appendix A. Important safety information Safety notices This information can help you safely use your computer. Follow and retain all information included with your computer. The information in this document does not alter the terms of your purchase agreement or the Limited Warranty. For more information, see "Warranty Information" in the Safety and Warranty Guide that comes with your computer. Customer safety is important. Our products are developed to be safe and effective.
Protect yourself from the heat generated by the ac power adapter. When the ac power adapter is connected to an electrical outlet and your computer, it generates heat. Extended contact with your body, even through clothing, may cause a skin burn. • Do not place the ac power adapter in contact with any part of your body while it is in use. • Never use it to warm your body. • Do not wrap the cords around the ac power adapter while in use. Prevent your computer from getting wet.
Handle your computer gently. Do not drop, bump, scratch, twist, hit, vibrate, push, or place heavy objects on your computer, display, or external devices. Carry your computer carefully. • Use a quality carrying case that provides adequate cushioning and protection. • Do not pack your computer in a tightly packed suitcase or bag. • Before putting your computer in a carrying case, make sure that it is off, in sleep mode, or in hibernation mode.
• Power cords, plugs, power adapters, extension cords, surge protectors, or power supplies that are cracked, broken, or damaged. • Signs of overheating, smoke, sparks, or fire. • Damage to a battery (such as cracks, dents, or creases), discharge from a battery, or a buildup of foreign substances on the battery. • A cracking, hissing, or popping sound, or strong odor that comes from the product.
When replacing CRUs, be cautious of sharp edges or corners that might cause injury. If you suffer an injury, seek medical care immediately. Power cords and power adapters DANGER Use only the power cords and power adapters supplied by the product manufacturer. The power cords shall be safety approved. For Germany, it shall be H03VV-F, 3G, 0.75 mm2, or better. For other countries, the suitable types shall be used accordingly. Never wrap a power cord around a power adapter or other object.
Plugs and outlets DANGER If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged or corroded, do not use the outlet until it is replaced by a qualified electrician. Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement.
General battery notice DANGER Batteries supplied by Lenovo for use with your product have been tested for compatibility and should only be replaced with approved parts. A battery other than the one specified by Lenovo, or a disassembled or modified battery is not covered by the warranty. Battery abuse or mishandling can cause overheat, liquid leakage, or an explosion. To avoid possible injury, do the following: • Do not open, dissemble, or service any battery. • Do not crush or puncture the battery.
The Lenovo-authorized repair facilities or technicians recycle Lenovo batteries according to local laws and regulations. When replacing the lithium coin-cell battery, use only the same type or equivalent type that is recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Swallowing the lithium coin-cell battery will cause chocking or severe internal burns in just two hours and might even result in death.
Heat and product ventilation DANGER Computers, ac power adapters, and many accessories can generate heat when turned on and when batteries are charging. Notebook computers can generate a significant amount of heat due to their compact size. Always follow these basic precautions: • When your computer is turned on or the battery is charging, the base, the palm rest, and some other parts may become hot.
Electrical current safety information DANGER Electric current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: • Do not use your computer during a lightning storm. • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. • Connect all power cords to a properly wired and grounded electrical outlet. • Connect properly wired outlets to any equipment that will be attached to this product.
Liquid crystal display (LCD) notice CAUTION: The liquid crystal display (LCD) is made of glass, and rough handling or dropping the computer can cause the LCD to break. If the LCD breaks and the internal fluid gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes; if any symptoms are present after washing, get medical care.
Glass parts notice CAUTION: Some parts of your product may be made of glass. This glass could break if the product is dropped on a hard surface or receives a substantial impact. If glass breaks, do not touch or attempt to remove it. Stop using your product until the glass is replaced by trained service personnel. Static electricity prevention Static electricity, although harmless to you, can seriously damage computer components and options. Improper handling of static-sensitive parts can damage the part.
Cleaning and maintenance With appropriate care and maintenance your computer will serve you reliably. The following topics offer information to help you keep your computer working with best performance. Basic maintenance tips Here are some basic points about keeping your computer functioning properly: • If possible, place your computer in a well-ventilated and dry area without direct exposure to sunshine.
78 E590, R590 and E595 User Guide
Appendix B. Accessibility and ergonomic information This chapter provides information about accessibility and ergonomics. Accessibility information Lenovo is committed to providing users who have hearing, vision, and mobility limitations with greater access to information and technology. This section provides information about the ways these users can get the most out of their computer experience. You also can get the most up-to-date accessibility information from the following Web site: https://www.
keyboard with all the standard keys. You can select keys using the mouse or another pointing device, or you can tap to select the keys if your computer supports multi-touch screen. • High Contrast High Contrast is a feature that heightens the color contrast of some text and images on your screen. As a result, those items are more distinct and easier to identify. • Personalized keyboard Adjust keyboard settings to make your keyboard easier to use.
– Change the size of all the items on your screen. 1. Right-click a blank area on the desktop and then click Display settings ➙ Display. 2. Change the item size by following the on-screen instructions. For some applications, your configuration might not take effect until you sign out and then sign in again. – Change the size of the items on a Web page. Press and hold Ctrl, and then press the plus-sign key (+) to enlarge or the minus-sign key (–) to reduce the text size.
Display: Position the display to maintain a comfortable viewing distance of 510 mm to 760 mm (20 inches to 30 inches). Avoid glare or reflections on the display from overhead lighting or outside sources of light. Keep the display screen clean and set the brightness to levels that enable you to see the screen clearly. Press the brightness control keys to adjust display brightness. Head position: Keep your head and neck in a comfortable and neutral (vertical, or upright) position.
Appendix C. Compliance information This chapter provides regulatory, environmental, RoHS, and ENERGY STAR information about Lenovo products. Radio frequency compliance statements Computer models equipped with wireless communications comply with the radio frequency and safety standards of any country or region in which it has been approved for wireless use.
The following illustration shows the antennas locations on your computer: 1. Wireless-LAN antenna (auxiliary) 2. Wireless-LAN antenna (main) Locate wireless regulatory notices For more information about the wireless regulatory notices, refer to the Regulatory Notice at https:// support.lenovo.com.
Mexico Advertencia: En Mexico la operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada. Singapore Korea 무선설비 전파 혼신 (사용주파수 2400∼2483.5 , 5725∼5825 무선제품해당) 해당 무선설비가 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없음 SAR 정보 본 장치는 전파 노출에 대한 가이드라인을 충족합니다. 본 장치는 무선 송수신기 입니다.
accordance with local regulations concerning waste electrical and electronic equipment (WEEE). These regulations determine the framework for the return and recycling of used appliances as applicable within each geography. This label is applied to various products to indicate that the product is not to be thrown away, but rather put in the established collection systems for reclaiming these end of life products.
Disposal of a lithium battery must comply with local ordinances and regulations. Dispose of a disused battery from Lenovo notebook computers Your Lenovo notebook computer has a lithium ion battery or a nickel metal hydride battery. If you are a company employee who uses a Lenovo notebook computer and need to dispose of a battery, contact the proper person in Lenovo sales, service, or marketing, and follow that person's instructions. You also can refer to the instructions at: https://www.lenovo.
and accumulators on the environment and human health due to the potential presence of hazardous substances. Before placing electrical and electronic equipment (EEE) in the waste collection stream or in waste collection facilities, the end user of equipment containing batteries and/or accumulators must remove those batteries and accumulators for separate collection.
Battery recycling information for the United States and Canada Restriction of Hazardous Substances (RoHS) Directive of countries and regions The latest environmental information about Lenovo products is available at: https://www.lenovo.
90 E590, R590 and E595 User Guide
Taiwan RoHS Electromagnetic emission notices Federal Communications Commission (FCC) Supplier’s Declaration of Conformity The following information refers to the following products: • ThinkPad E590, machine types: 20NB and 20NC • ThinkPad E595, machine type: 20NF This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Lenovo is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt ohne Zustimmung der Lenovo verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohne Empfehlung der Lenovo gesteckt/eingebaut werden. Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit von Betriebsmitteln, EMVG vom 20. Juli 2007 (früher Gesetz über die elektromagnetische Verträglichkeit von Geräten), bzw.
• On a physical label attached to the outside of your computer shipping carton • On a physical label attached to your computer • Through an electronic-label screen (E-label screen) preinstalled on your computer To access the E-label screen, do one of the following: • Restart the computer. When the logo screen is displayed, press F9. The E-label screen is displayed. • Restart the computer. When the logo screen is displayed, press Enter or tap the prompt to enter the Startup Interrupt menu.
ENERGY STAR model information ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy aimed at saving money and protecting the environment through energy efficient products and practices. Lenovo is proud to offer our customers products with an ENERGY STAR compliant designation. The following machine types have been designed and tested to conform to the ENERGY STAR program requirement for computers at the time of manufacture.
96 E590, R590 and E595 User Guide
Appendix D. Notices and trademarks Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary.
