User's Manual Part 4

- 13 -
c. Make sure the system should be setup in Auto dial mode.
3. NOT REMOTE CONTROL FUNCTION
a. Check if battery low and battery replacement.
b. If it doesn't work, re-learn ID code again, according to " TO LEARN WIRELESS SENSOR OR REMOTE CONTROL
ID CODE ".
TIPS
1. Make sure the full telephone has been stored.
2. If you are leaving pets at home while the Auto-Dialer is ON, then make sure the Auto-Dialer has been set in a
location high enough not to detect any animals walking around but not too high to detect other movement.
3. Keep the Auto-Dialer dust free, away from cobwebs that may cause movement in the protected area.
4. Only suitable for single phone lines. Not compatible with fax machines.
NOTE:This valuable manual will let your security system work properly. Please preserve this
manual at your record, and keep reading when need some trouble obviation.
INTRODUCTION
HomeSafe's unique wireless security/safety Alarm system with Auto dialer concentrates on the protected area you select.
Whenever the main unit is set at ARMED, the wireless motion detection sensor or wireless door/window sensor will
concentrate on the protected area. Once there is movement or door/window open detected, the alarm will turn on and call to
the memorized telephone numbers one by one. In chime mode, the chime will Ding Dong when movement be detected.
IMPORTANT SAFETY TIPS
1. Do not install the system where it will be exposed to direct sunshine or rain.
2. The system siren is very loud, never put the unit close to your ear.
3. The unit should be away from heat sources such as radiators, heating ducts and stoves.
4. If the system sounds at random, it is possible that the location too close to a heat source, changing the location or
direction of the unit can remedy this.
5. The system can provide valuable protection for your home and property if utilized properly. However, this unit cannot
guarantee complete protection against to burglary or robbery. Therefore, we will not be responsible for any losses or
damages which occur, during use of this product.
DESCRIPTION OF COMPONENTS
FEATURES
Detecting motion or door/window open activates auto-dialer and alarm
16 Digit large number display with date/time and function icon
9 zone icon for easy differentiating intruder location
Room monitor and broadcast by telephone function
Remote turn system to ARM or DISARM by telephone function
Programmable security code, entry delay timing
5 emergency telephone numbers (up to 32 digits each)
Programmable auto dialling cycle
5 Trigger recorder with zone indication for alarm mode
PAUSE key
PANIC key
- 1 -
PROG key
Built-in 20 seconds Voice REC./Play back IC for help message
Built-in flash memory to protect system data for power failure
Battery Low indicator
DTMF(Tone )dialling only
Home mode function
Trigger AC socket by radio linked function
AC adaptor operated (included) with 9V battery back-up (not included)
Wall mountable
Built-in 105 dB alarm (with programmable alarm on/off)
Compatible with additional up to 16 wireless motion detector sensor or wireless window/door sensor and 8
wireless remote control or wireless control AC socket or wired sensor to EXPANDING the system
Trigger AC Socket by radio linked function
INSTALLATION
1. Remove the screw of main unit from battery compartment cover, install an alkaline 9V battery, this is a back-up
battery, in case of AC power failure. This battery will keep the unit working (Fig.1)
OPEN
121110
13
14
18
15
16
17
SYSTEM SETTING
This program can only be operated during standby mode. During set-up, if not key in any message within 15 seconds,
the system will auto exit set-up mode.
Your auto-dialer has a factory preset pass number of 0-0-0. This can now be changed to a pass number personal to you.
1 TO CHANGE PASSWORD
a. Enter factory pre-set pass number, 0-0-0. Press PROG button once, PASSWORD will flash on the auto-dialer
screen.
b. Press the ARM/DISARM button to confirm that you want to enter the PASSWORD option.
c. Enter your new pass number followed by the ARM/DISARM button to confirm the new number. (You can choose 3~
6 numbers in your pass number)
d. You can press #/DOWN button or /UP button select other setup, or press the PROG button nine times to exit
set-up mode.
NOTE: If you forget your pass number, press and hold PROG button, use a pen to touch “RESET” button once of unit
bottom, the LCD will split second not display, unpress PROG button after LCD comeback display date time, the
auto-dialer will restore back to the factory pre-set pass number 0-0-0, all the setup will be remained as you programmed
except the date and time and password.
2 TO STORE TELEPHONE NUMBERS
a. Enter the pass number followed by PROG button twice.
b. MEMORY will flash on the auto-dialer screen.
c. Press the ARM/DISARM button to confirm this is the option you need.
d. You are now ready to program in your 5 chosen telephone numbers. Press the /UP and #/DOWN buttons to select
1 - 5, For example if you select 4 this will be the fourth number dialed.
e. Now enter the number that you want to store, followed by ARM/DISARM to confirm and store the number (maximum of
32 numbers, but LCD only show last 16 digits)
f. Repeat steps c-e for the four other numbers you wish to be stored.
g. You can press #/DOWN button or /UP button select other setup, or press the PROG button eight times to exit the
set-up mode.
3 TO DELETE TELEPHONE NUMBER IN MEMORY
a. Enter the pass number followed by PROG button twice.
( Fig. 5)
PASSWORD
(Fig. 4)
( Fig. 3b )
DC 9V Adaptor
( Fig. 3a )
2. The unit with a external antenna which plug into the antenna jack, the antenna should be vertical, since it may come
out of the package bent can simply bend it back to a straight position (Fig.2).
3. Connect the line cord between "LINE" jack and telephone wall socket. (Fig.3a)
4. Now connect the plug/wire included with your auto-dialer (this is the plug/wire with the clear plugs at either end) one
end inserted in the TEL socket on the auto-dialer, and the other end into your telephone. You now have a wire from
the TEL socket on your auto-dialer to your telephone. You should now have a dial tone.
5. Plug the AC adaptor to the DC 9V socket on the auto-dialer. (Fig. 3b)
6. For wall mount-If required
Choose a suitable location, 5 - 6 feet (1.5 - 2.0 meters) away from floor, then use the template provided to mark location,
drill holes and install anchors and screws Place the unit over the screws and slide it down to secure in place. (Fig 4)
7 TO PROGRAM AUTO DIALLING CYCLE.
The auto-dialer has been factory set for auto dialling 3 cycles. (When system is trigger the auto dialer will call all stored
numbers 3 times) You can change this cycle from 1 - 5 dialling times.
a. Enter the pass number followed by PROG button six times.
b. CYCLE will now flash on the auto-dialer screen.
c. Press ARM/DISARM button to confirm.
d. Using the UP and DOWN buttons to select 1 - 5 followed by the ARM/DISARM button to confirm the cycle (how
many times the Auto-dialer will call you if motion is detected)
e. You can press #/DOWN button or /UP button select other setup, or press the PROG button four times to exit set
up mode.
8 TO PROGRAM CALL-IN RING DETECT CYCLE.
The call-in ring detect cycle for how many call-in ring cycle the Auto-dialer will answer, The auto-dialer has been factory
set for 5 cycles, you can change this cycle from 3, 5, 7, 10 cycles.
a. Enter the pass number followed by PROG button seven times.
b. “ ” will now flash on the auto-dialer screen.
c. Press ARM/DISARM button to confirm.
d. Using the UP and DOWN buttons to select 3, 5, 7, 10 followed by the ARM/DISARM button to confirm the cycle.
e. You can press #/DOWN button or /UP button select other setup, or press the PROG button three times to exit set
up mode.
9 TO PROGRAM ENTRY DELAY TIME
The auto-dialer has been factory set for a 20 second delay time. You can change this to 0,5,10,15, or 20 seconds:
a. Enter the pass number followed by PROG button eight times.
b. ENTRY will now flash on the auto-dialer screen.
c. Press the ARM/DISARM button to confirm that this is the option you need.
d. Using the UP and DOWN buttons select the seconds 0,5,10,15 or 20. Press ARM/DISARM to confirm the number
of seconds you require for the entry delay time.
e. Press the PROG button twice to exit set-up mode.
10 REAL TIME SETTING
a. Enter the pass number followed by PROG button seven times.
b. “ ” will flash on the auto-dialer screen.
c. Press the ARM/DISARM button to confirm that this is the option you need.
d. The date will show in the auto-dialer screen as three sets of numbers, year, month and date followed by the real
time. The first set of numbers will flash confirming that these can now be changed.
e. Press the ARM/DISARM button on the flashing numbers and using the UP and DOWN buttons select the correct
date followed by the ARM/DISARM button to confirm and store. You will now have the correct date and time.
f. Press the PROG button once to exit set-up mode.
11. TO RECORD /PLAYBACK THE NOTIFICATION MESSAGE
This function for users to record the alarm notification message that will play during an alarm notification call. The total
recording time about 20 seconds.
It is best to use the message to notify that there has been an alarm activation, and also to specify exactly how the call
recipient can respond (room monitor, broadcast), make sure that you speak clearly and steadily, approximately ten inches
from the microphone. Keep in mind that you have exactly address and name have been properly recorded.
a. enter the password followed “REC./PLAY” button once, the REC./PLAY led will light up .
b. begin recording the message for up to 20 seconds
c. press “REC./PLAY” button again to end the record or automatic ending after the 20 seconds, and the message will
automatic playback.
d. Press “REC.PLAY” button at standby mode, the unit will play recorded notification message once.
NOTE: to listen notification message, the speaker HI/LO/OFF switch must set at HI or LO location.
TO TEST MEMORY DIALLING
In standby mode, press and hold the PROG button for more than two seconds, hear a beep tone, then key in the test
telephone number memory location, the telephone number stored in memory will automatically be dialed.
TO TEST WIRELESS SENSOR TRANSMITTING RANGE
After selecting a location for the unit, press HOME button of the Auto-Dialer, and wait 60 seconds and then trigger
wireless sensor, The Auto-Dialer will receive trigger signal sound DING - DONG and LCD show sensor zone number.
Press HOME button again after this test.
OPERATION
1 TO ARM THE SYSTEM
a. Enter the pass number followed by the ARM/DISARM button.
b. Three short beeps will sound and the ARM icon will show on the Auto-Dialer screen.
c. You can press and hold "ARM" button 2 seconds on remote unit to ARM main unit.
- 3 -
b. MEMORY will flash on the auto-dialer screen.
c. Press the ARM/DISARM button to confirm that this is the option you need.
d. Press the UP and DOWN buttons to select the number you want to delete.
e. Press the DEL./PAUSE button to delete the number.
f. Press the ARM/DISARM button to confirm the correct number has been deleted.
g. You can press #/DOWN button or /UP button select other setup, or press the PROG button eight times to exit the
set-up mode.
4 TO LEARN WIRELESS SENSOR OR REMOTE CONTROL ID CODE
All the Expanding Wireless Sensor and remote control attached with the package of this system are all completed done
the LEARN CODE. The whole units are standby for use after installation directly.
The system with 10 zone for wireless sensor and remote control, zone 1~ zone 8 only learn 1 wireless sensor id code for
each, zone 9 can learn 8 wireless sensor id code. Zone 10(LCD icon REMOTE) is remote control zone can learn 8
remote control id code. So you can additionally purchased extra 16 wireless Motion Detector sensor (615PR, 616PR) or
wireless Door/Window sensor (600WR, 218WR) and 8 remote control (200R, 300R) to expanding the system, but it is
required to LEARN the sensor and remote control unit id code to the main unit, Follow these steps:
a. Enter the pass number followed by PROG button three times.
b. The " LEARN " icon will flash on the auto-dialer screen.
c. Press ARM/DISARM to confirm that this is the option you need, the system will into learn code setup and zone 1
icon flash.
d. Press the /UP and #/DOWN buttons to select you want setup zone, when LCD display “NO ID CODE” is meaning
the zone is disengaged, you can learn new sensor id code for this zone; when LCD display “FULL” is meaning the
zone has id code, you can select other zone or press DEL./PAUSE button to delete original id code then relearn new
id code for this zone.
e. press ARM/DISARM to confirm the zone location.
f. Trigger wireless motion detector sensor (swing at sensor lens by hand) or door/window sensor (open/close the
magnetic switch) or press any key for remote control, you will hear a long beep tone confirm learn code successfully
and LCD will display “FULL” for zone 1 ~ zone 8 or “1 ID CODE IN” for zone 9 and remote control.
g. You can press #/DOWN button or /UP button select other setup, or press the PROG button seven times to exit the
set-up mode.
5 TO PROGRAM SIREN ON/OFF
The auto-dialer has been factory set with the siren ON. To change this to OFF:
a. Enter the pass number followed by PROG button four times.
b. The " " icon will flash on the auto-dialer screen. (Fig.8)
c. Press ARM/DISARM to confirm that this is the option you need.
d. Using the UP and DOWN buttons select SOUND OFF. Followed by the ARM/DISARM button to confirm that the
SIREN is now off.
e. You can press #/DOWN button or /UP button select other setup, or press the PROG button six times to exit the
set-up mode.
6 TO PROGRAM AUTO CALL FUNCTION ON/OFF
The auto-dialer has been factory set with the call option ON. To change this to call option to OFF:
a. Enter the pass number followed by PROG button five times.
b. The " " icon will flash on the auto-dialer screen. (Fig.9)
c. Press the ARM/DISARM to confirm that this is the option you need.
d. Using the UP and DOWN buttons select call OFF followed by the ARM/DISARM button to confirm call OFF.
e. You can press #/DOWN button or /UP button select other setup, or press the PROG button five times to exit the
set-up mode.
MEMORY
1
2
3
4
5
MEMORY LOCATION
(Fig.6)
(Fig.8)
(Fig.9)
(Fig.7)
LEARN
1 2 3 4 5 6 7 8 9
REMOTE
ZONE NUMBER
PAUSE FUNCTION
The "PAUSE" function can be stored as one digit in the telephone number memory for some PABX dialling operation and
every one "PAUSE" in the memory dialling sequence will stop for 3.6 seconds. For example, if you store telephone
number "7,7,7,5,3,5,5---226" to memory location 2, operation as follows:
a. Press password (0-0-0), then press "PROG" button, the system will into setup mode.
b. Press PROG button to select function menu "MEMORY" icon flash.
c. Press "ARM/DISARM" button to confirm.
d. The system will get into first telephone number setting and LCD display.
e. Press " /UP" or "#/DOWN" to select memory location 2.
f. Press "7,7,7,5,3,5,5" , Pause "2,2,6".
g. Press "ARM/DISARM" button to confirm and the LCD will return display setup menu.
BATTERY LOW INDICATOR
When main unit the 9V battery is running low, the battery low LED will flash once every 3 seconds to indicate the low
battery. When wireless sensor battery low, the LCD will show battery icon and sensor zone number.
NOTE: Change to a new battery immediately, otherwise it may cause the sensor to not detect properly and may appear
the false trigger alarm and dialling.
VIEW FUNCTION
View Trigger Records
In standby mode, press "#/DOWN" to view last 5 trigger records.
View store telephone numbers
In standby mode, press " /UP" to view stored telephone number.
NOTE: Not press any button for 10 seconds or system will automatically exit view mode.
END OF CALL - press “ 0” the auto-dialer will end of call for the trigger and automatically disconnected the telephone
line.
ARM SYSTEM – press “1, pass word (pre-set: 000), 1” after three short beep tone confirm system is armed and
automatically disconnected the telephone line.
DISARM SYSTEM – press “2, pass word (pre-set: 000), 2” after a beep the auto-dialer will disarm and automatically
disconnected the telephone line.
TURN ON WIRELESS AC SOCKET- press “3, pass word, 3” after a beep the auto – dialer will sending a radio link
signal to turn on wireless AC SOCKET(688R) and automatically disconnected the telephone line. (The wireless AC
SOCKET for optional)
HOME MODE FUNCTION
This function for In home mode to monitor room state, when system receive wireless sensor trigger signal in the
protected area，LCD will show trigger sensor zone number and sound DING-DONG, you can programmable which
zone wireless sensor enable or disable.
1. Turn the system to home mode:
a. Press HOME button once will hear ding-dong sound and LCD show HOME icon.
b. Wait for 60 Seconds, there will be one beep.
c. When received wireless sensor trigger signal in the protected area the 'DING DONG' chime will sound.
d. Press HOME button again to turn system exit home mode.
NOTE: When the Auto-dialer is in ARM mode the CHIME will NOT sound.
2. Wireless sensor enable/disable for home mode
the system pre-set all zone at ON(enable), to change which zone to OFF(disable), follow these steps:
a. Enter the pass number followed by HOME button once.
b. zone 1 icon now flash on the auto-dialer screen.
c. Using the UP and DOWN buttons to select you want change zone number.
d. press ARM/DISARDM button to confirm then using UP or DOWN button select ON or OFF, press ARM/DISARM
button to confirm.
e. press the HOME button once to exit set up mode.
OPTIONAL WIRELESS ACCESSORIES
MODEL 218WR (Wireless Slim Door/Window Sensor)
INSTALLATION
1. Remove the screw from the battery compartment cover.
2. Install 2 “CR2032” batteries (included) on the battery box, ensure the polarity is correct.
3. Replace the battery cover and screw.
4. Mount the magnetic door/window sensor
Choose a suitable location, stick the main unit to the door/window frames by attached double – side tape. Then stick
the magnetic unit (smaller unit) to the door/window by attached double-side tape and make sure to align the “ ”mark
to right “ ”mark on the main unit and “ ” facing “ ” at no more than 1/4” apart as shown below. (Fig.1)
5.External Magnetic sensor terminal
You can additionally wire magnetic sensor to expanding you desired detection area.
a.Remove the screw from the battery compartment cover.
b.Remove the screw from terminal and take out connected wire. (Fig.2)
c.Measure the length of wire needed to connect the sensor to the transmitter, then cut the wire to the correct length.
Strip about 1/2 inch of insulation from the wire ends, and twist the wires together.
d.Connect the sensor switch on door to the main terminal post using the wire you just cut. (There is no polarity need to
be taken care of, any terminal will be fine, as long as the wires from a loop)
e.Connect another sensor switch screw to another switch terminal post by using the parallel another wire as shown
below. (Fig.3)
f.If you connect more than one sensor to the main unit, connect them in series as shown below. (Fig.4)
NOTE: After select a location, you should test the sensor transmitting range before mount it permanently, turn the CHIME
switch to ON of main unit, then open/close the magnetic switch of door/window sensor to trigger, you will hear the main
unit sounds “DING DONG” chime if signal is received successfully, if not, draw out mini retractable antenna or change
location as required.
LEARNING CODE TO MAIN UNIT
The wireless door/window sensor with the package of this system are completed done the LEARN CODE. The whole units
are standby for use after installation directly. When relearn code operation see main unit manual.
OPERATION
After 60 seconds installed battery, the unit will into standby mode. Once the door/window opened or vibration detected, the
unit will output wireless radio signal and LED will flash.
(Fig.1a) (Fig.1b)
(Fig.4)
(Fig.3)
(Fig.2)
- 8 -
BATTERY LOW INDICATOR
When battery goes low, the LED will light on 3 seconds and off 1 second, change 2 new CR2032 batteries immediately, or
the sensor might not detect properly.
MODEL 600WR (Wireless Door/Window Sensor with Alarm)
INSTALLATION
1. Remove the screw from the battery compartment cover. (Fig.1)
2. Install an alkaline 9V battery.
3. Replace the battery cover and screw.
4. Mount the magnetic door/window sensor-
Choose a suitable location, then use the template provided to mark location, drill holes and install anchors and screws.
Place the unit over the screws and slide it down to secure in place. (Fig.2)
5． Mount the magnetic wired piece to the door or window frame and another single piece to the door/window by using the
double-side tapes (included) and aligned the 2 sensor pieces to be flushed and “ ” facing “ ” at no more than1/4”
apart as shown in. (Fig.3)
6. If you connect more than one sensor to the main unit, connect them in series as shown below. (Fig.4)
NOTE: After select a location, you should test the sensor transmitting range before mount it permanently, turn local alarm
switch to OFF, turn the CHIME switch to ON of main unit, then open/close the magnetic switch of door/window sensor to
trigger, you will hear the main unit sounds “DING DONG” chime if signal is received successfully, if not, draw out mini
retractable antenna or change location as required.
LEARNING CODE TO MAIN UNIT
The wireless door/window sensor with the package of this system are completed done the LEARN CODE. The whole units
are standby for use after installation directly. When relearn code operation see main unit manual.
OPERATION
After 60 seconds installed 9V battery, the unit will into standby mode. Once the door/window opened or vibration detected,
the unit will output wireless radio signal and LED will flash, then sound alarm 3 seconds, you can turn alarm switch select
on or off.
BATTERY LOW INDICATOR
When 9V battery goes low, the LED will light on 3 seconds and off 1 second, change a new alkaline 9V battery immediately,
or the sensor might not detect properly.
(Fig.1)
(Fig.4)
(Fig.3)
ON
OFF
ALARM
(Fig.2)
WIRELESS SECURITY/
SAFETY ALARM SYSTEM
WITH AUTO DIALER
- 2 -
- 4 -
- 6 -
- 7 -
- 12 -
( Fig. 6)
arrow facing arrow
( Fig. 7 )
NOTE: Slave PIR unit and water alarm selection option alternative.
3. Connect the extended outdoor siren cable to the terminal post located in the back of main unit inside the terminal
compartment. The polarity as shown below. (Fig.3)
NOTE: The outdoor siren (515SK/E)option, not included.
4. Connect the magnetic sensor (detect door/window is opened, will trigger auto dialer and alarm after "entry delay time").
(NOTE: The magnetic is for optional, not included)
a. Measure the length of wire needed to connect the sensor to the transmitter, then cut the wire to the correct length.
Strip about 1/2 inch of insulation from the wire ends, and twist the wires together.
b. Connect the sensor switch on door to the main terminal post using the wire you just cut. (There is no polarity need to
be taken care of, any terminal will be fine, as long as the wires from a loop).
c. Connect another sensor switch screw to another switch terminal post by using the parallel another wire as shown
below. (Fig.4)
d. Wire not included.
NOTE: If you connect more than one sensor to the main unit, connect them in series as shown below. (Fig.5)
5. Mount the magnet sensor to the door/window frame by using the double-side tapes and aligned the 2 sensor pieces to
be tidiness and "arrow" facing "arrow" at no more than 1/4 inch apart. (Fig.6)
6. To mount the outdoor siren use the siren stand as a template, mark locations of holes and install anchors and screws
as shown below (Fig.7). It is recommended that you mount the out door siren at entrance door, top of garage door, or any
location which is sheltered from easy tamper and rain.
TROUBLE SHOOTING GUIDE
1. UNIT WILL NOT ARMED/DISARM
a. Make sure you've entered the correct password, if not, reenter the password.
b. If still doesn't work. use a pen to touch “RESET” button once of unit bottom, then try to ARM/DISARM again.
2. UNIT WILL NOT DIALLING
a. Make sure the telephone line be in good connection.
b. Make sure the telephone number stored.
Sensor Switch
(Mount the door/window frame)
Magnet sensor
(Mount the door/window frame)
( Fig.4 )
Slave Unit
Sensor Switch
( Fig.3 )
Main unit
Black striped wire
to negative (-)
( Fig. 2)
( Fig.5)
- 5 -
3 TO DISARM THE SYSTEM
a. Enter the pass number followed by the DISARM button.
b. You will hear one beep and the ARM icon will disappear from the Auto-Dialer screen to confirm that the Auto-Dialer
has been DISARMED.
c. You can press and hold "DISARM" button 2 seconds on remote unit to DISARM main unit.
4 PANIC BUTTON
a. Press "PANIC" button on main unit or press and hold "PANIC" button 2 seconds on remote control, the ALARM will
sound instantly for 30 seconds, and the Auto-Dialer will begin dialling the stored numbers.
b. To stop the alarm and the stored numbers being dialed, Press password then ARM/DISARM button.
c. Or press and hold "DISARM" button 2 seconds on remote unit to stop the alarm and auto dialer.
5． REMOTE CONTROL BY TELEPHONE OPERATION
This function for responding during an alarm notification call or remote access from any outside telephone, you can use
any tone (DTMF) dialing telephone or mobile phone to turn system ARM or DISARM or ROOM MONITOR or
BROADCAST or Turn on wireless AC SOCKET(688R)
A. RESPONDING DURING AN ALARM NOTIFICATION CALL
a).Upon an alarm activation, the auto-dialer will call out to each of the programmed phone numbers.
b). Answer the call, you will hear a single beep tone for motion detector sensor trigger or door/window sensor vibration
trigger or continuous two beep tone for door/window open trigger or continuous four beep tone for PANIC button
trigger, press “00”on the phone to turn auto-dialer in waiting state and will sound two beep tone, (when you not hear
beep tone press “00” again on the phone). Press key for the desired function as follows:
c). For room monitor and broadcast within 50 seconds operation time, a beep sound after 30 seconds reminds user of
the time will end. You can press “00” turn the system to be in waiting state then enter the operation code you want,
automatically disconnect the telephone line after 50 seconds for not operation.
B. REMOTE CONTROL BY TELEPHONE FOR CALL BACK
a).using mobile phone or tone dialing phone call the home number of the line the system is connected. The auto-dialer
will answer and sound a beep tone after call-in ringer detect cycle (the call-in ringer detect cycle can programmable,
the factory pre-set 5 cycles, you can change to 3, 7, 10 cycles).
b). enter PASSWORD you will hear two beep tone.
c). press “00”on the phone to turn auto-dialer in waiting state and will sound a beep tone, (when you not hear beep
tone press “00” again on the phone.), Press key for the desired function as follows:
OWNER'S MANUAL
Function
Press key
Room monitor
Broadcast
End of call
Disarm system
2 pass word 2
Function
Press key
Room monitor
Broadcast
ARM system
1 pass word 1
Disarm system
2 pass word 2
Turn on wireless AC socket
3 pass word 3
TEL.LINE
TEL.LINE
TEL.LINE
- 11 -
(Fig.1)
(Fig. 2)
PANIC
DISARM
ARM
(Fig.2)
MODEL 200R (Wireless Remote Control)
1.Battery install and replacement (Battery Type-23A 12V)
a. Remove the battery compartment cover by sliding it in the direction of the arrow.
b. Replace with new batteries of the same type.
Make sure the polarity (+ or -) of the batteries match the polarity marks inside the unit. As shown below. (Fig. 1)
c. Replace battery cover.
LEARNING CODE TO MAIN UNIT
The wireless remote control with the package of this system are completed done the LEARN CODE. The whole units are
standby for use after installed directly. When relearn code operation see main unit manual.
Notes for remote operation
● If radio linked remote control operation range becomes shorten, replace the batteries according to "BATTERIES
REPLACEMENT".
● The battery life should be about six months under normal use, so replace battery at least every 6 months. Effective
range. (Fig. 2)
(Fig.1B)
Slave Unit
From Main Unit
Slave Extended Cable
OPTIONAL WIRED ACCESSORIES
1. Connect the PIR slave extended unit (not included, option for 113E)
a. Connect the PIR slave extended unit cable to the terminal post located in back of the main unit inside the terminal
compartment. See polarity below. ( Fig.1A)
b. Plug the 3.5mm diameter male plug of slave extended cable that from the main unit into the jack located on side of
the unit. (Fig.1B)
2. Connect the water alarm (not included, option for 760A)
Connect the water alarm to the terminal post located in the back of main unit inside the terminal compartment. The
polarity as shown below. (Fig.2)
( Fig.1A )
Red
Black
White
about 30
～
40 meters
(
open space)
about 20
～30 meters
(
open space)
(Fig.1)
(Fig.2)
(Fig.3)
1.5~2M
1.5~2M
MODEL 615PR (Wireless Motion Detector Sensor)
INSTALLATION
1. Remove the screw from the battery compartment cover. (Fig.1 ）
2. Install an alkaline 9V battery.
3. Replace the battery cover and screw.
4. Mount the wireless motion detector sensor-
Choose a suitable location, 5 - 6 feet (1.5 - 2.0 meters) away from floor, then use the swivel wall mount bracket template
provided to mark location, drill holes and install anchors and fix the bracket by screws, Place the main unit into the
bracket and slide it down to secure in place (Fig 2). You can adjust bracket to obtain the best coverage of the intended
protected area. (Fig 3)
LEARNING CODE TO MAIN UNIT
The wireless motion detector sensor with the package of this system are completed done the LEARN CODE. The whole
units are standby for use after installed directly. When relearn code operation see main unit manual.
WALK TESTING MOTION DETECTOR SENSOR
After select a location, you should test the sensor transmitting range before mount it permanently, press HOME button of
main unit, ofter 60 seconds ,then swing at sensor lens by hand, you will hear the main unit sounds “DING DONG” chime
if signal is received successfully, if not, change location as required.
You can test the sensor detection area. Temporarily place the detector at the mounting location and the chime sound will
be heard from the main unit. If you walk beyond the sensor detection area, then there will not be a chime sound, by
adjusting the sensor direction, or the installation location, you can get you desired detection area coverage.
BATTERY LOW INDICATOR
When 9V battery goes low, the LED will light on 3 seconds and off 1 second, change a new alkaline 9V battery immedi-
ately, or the sensor might not detect properly.
MODEL 616PR (Wireless Motion Detector Sensor)
INSTALLATION
1. Remove the screw from the battery compartment cover.
2. Install 3 “AA” alkaline batteries (not included) on the battery box, ensure the
polarity is correct.
3. Replace the battery cover and screw.
4. Mount the wireless motion detector sensor-
Choose a suitable location, 5 - 6 feet (1.5 - 2.0 meters) away from floor, then use
the swivel wall mount bracket template provided to mark location, drill holes and
install anchors and fixture the bracket by screws, Place the main unit into the
bracket and slide it down to secure in place. You can adjust bracket to obtain the
best coverage of the intended protected area.(Fig.1)
- 9 -
(Fig.1)
1.5~2M
(Fig.1)
- 10 -
MODEL 300R (Wireless Remote Control)
1. Batteries install and replacement
(Battery Type-LR44X3 or Similar)
a. Remove the battery compartment cover by screw driver and sliding open the battery Cover.
b. Replace with new batteries of the same type.
Make sure the polarity (+ or -) of the batteries match the polarity marks inside the unit. As shown below. (Fig.1)
c. Replace battery cover
LEARNING CODE TO MAIN UNIT
The wireless remote control with the package of this system are completed done the LEARN CODE. The whole units are
standby for use after installed directly. When relearn code operation see main unit manual.
Notes for remote operation
● If radio linked remote control operation range becomes shorten, replace the batteries according to "BATTERIES
REPLACEMENT".
● The battery life should be about six months under normal use, so replace battery at least every 1 year. Effective range.
(Fig. 2)
ADJUST DETECT DISTANCE
To increase sensitivity turn the sensitivity control toward MAX. to decrease sensitivity, turn the sensitivity control toward
MIN(Fig.2). However, too high sensitivity may result in false triggering, please note.
ADJUST DETECT ANGLE
The motion detector max detect angle is up to 150 degree, you can adjust slide window of lens left and right side to select
the angle you need. (Fig.3)
LEARNING CODE TO MAIN UNIT
The motion detector sensor is compatible with T015, T016, T018 main unit, must learn code to main unit then use, learn
code operation see main unit manual.
WALK TESTING MOTION DETECTOR SENSOR
After select a location, you should test the sensor transmitting range before mount it permanently, turn the CHIME switch
to ON of T015, T016 main unit or press HOME button of T018 main unit, after 60 seconds then swing at sensor lens by
hand, you will hear the main unit sounds “DING DONG” chime if signal is received successfully, if not, change another
location to test.
You can then test the sensor detection area. Temporarily place the detector at the mounting location and the chime sound
will be heard from the main unit. If you walk beyond the sensor detection area, and there will not be a chime sound, by
adjusting the sensor direction, or the installation location, you can get you desired detection area coverage.
BATTERY LOW INDICATOR
When batteries goes low, the LED will light on 3 seconds and off 1 second, change 3 AA size new alkaline batteries immedi-
ately, or the sensor might not detect properly.
MAX
MIN
(Fig.2) (Fig.3)
5.REC./Play LED 6. Battery Low LED 7. DC Power LED 8. Numerical Keys
9. MIC 10. Line jack 11. TEL. jack 12. DC 9V Power Jack
13. Buzze 14. Reset [ ] button
16. External Terminal
17. Wireless DC Socket Channel select jumper 18. Battery (Not included)
15. Battery Cover
d. There will be a further single beep after 60 seconds, the Auto-Dialer is now set at ARM.
e. Into arming, the system will detect door/window sensor state, when door/window is open, will sound beep tone 5
seconds and LCD show “CLOSE PLEASE” and sensor zone number, when still not close door/window will turn on
alarm and auto dialer after 60 seconds.
2 ALARM
a. In ARM mode system receive wireless sensor trigger signal in the protected area，LCD will show trigger icon and
trigger sensor zone number, after the entry time then sound a SIREN for 30 seconds on and 30 seconds off then 30
seconds on again, and will automatically dial the numbers stored, one by one, in the CYCLE you have chosen,
(amount of times the numbers are dialed). You will hear a beep tone for motion detector sensor trigger or
door/window sensor vibration trigger or two beep tone for door/window sensor open trigger or three beep tone for
PANIC button trigger when the call is answered, you can call the Police or make the necessary arrangements, ie
calling a neighbour.
b. In ARM mode, if the Auto-Dialer is set at SIREN OFF, the numbers stored will be dialed silently, when the call is
answered you will hear a siren and know that movement has been detected, enable you to call the Police or make
necessary arrangements, ie calling a neighbour. REMEMBER the Auto-Dialer has called you silently, no indication
whatsoever is given from the Auto-Dialer to suggest it is dialling you.
NOTE: the system with auto detect telephone line connect function, when telephone line is not connect, fist sound
four beep tone then sound siren and not dial out phone number.
d). For room monitor and broadcast within 50 seconds operation time, a beep sound after 30 seconds reminds user of
the time will end. You can press “00” turn the system to be in waiting state then enter the operation code you want,
automatically disconnect the telephone line after 50 seconds for not operation.
ROOM MONITOR - Press “ ” after the beep, you will be able to listen to all the sounds within the room for 50
seconds, a beep sound after 30 seconds remind of user the room monitor time will end. You can press “00” turn the
system to waiting state then enter you want operation code, automatically disconnected the telephone line after 50
seconds for not operation.
BROADCAST – press “# #” after the beep, The person in the room will hear your talking, you can speaking you want
for 50 seconds, a beep sound after 30 seconds remind the broadcast time will end, you can press “0 0” turn the
system to waiting state then enter the operation code you want, automatically disconnected the telephone line after
50 seconds for no operation.
MODEL: T018R