User's Manual

Wireless Motion Detector Sensor
Model 615NP
FEATURES
● Detect motion output wireless radio signal
● Swivel wall mount bracket kit
● Wireless RF transmission up to 50~70 meters
(open space)
INSTALLATION
1. Remove the screw from the battery compartment cover.
2. Install an alkaline 3 “AAA” alkaline battery.
3. Replace the battery cover and screw.
4. Mount the wireless motion detector sensor-
Choose a suitable location, 5 - 6 feet (1.5 - 2.0 meters)
away from floor, then use the swivel wall mount bracket
template provided to mark location, drill holes and install
anchors and fixture the bracket by screws, Place the main
unit into the bracket and slide it down to secure in place.
You can adjustable bracket obtain the best coverage of the
intended protected area.(Fig 1)
LEARNING CODE TO MAIN UNIT
The motion detector sensor compatible 116S, 116X, T015S, T016S, T018S, T055S, T056S, T058S/VS,
T068S, 639S, 526SL, 527SL, 528, 422R, 688R, 423R, 600R, 621S, 625R main unit, must learn code to
main unit then use, learn code operation see main unit manual.
HOW IT WORK
After 60 seconds installed battery, the unit will into standby mode. Once the motion detected, the
unit will output wireless radio trigger signal and LED flash.
WALK TESTING MOTION DETECTOR SENSOR
After select a location, you should test the sensor transmit range before mount it permanently. (The
transmit range testing method see main unit manual)
You can then test the sensor detection area. Temporarily place the detector at the mounting location
and the chime sound will be heard from the main unit. If you walk beyond the sensor detection area,
then there will not be a chime sound, by adjusting the sensor direction, or the installation location, you
can get you desired detection area coverage.
BATTERY LOW INDICATOR
When battery goes low, the LED will light on 3 seconds and off 1 second, change new “AAA” alkaline
battery immediately, or the sensor might not detection properly.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
The wireless motion detector sensor compatible
model with the following:
1.5~2M 1.5~2M
(Fig 1)
Wireless Security Alarm
/Auto Dialer System
Model T018S
ModelT056S
Wireless Security/
Safety Alarm System
With Auto Dialer
BATT.
LOW
1
4
7
/ UP
2
5
8
0
3
6
9
PROG
/DOWN
PANIC
AC
Model T055S
WirelessSecurity/
Safety Alarm System
With Auto Dialer
1
4
7
/ UP
2
5
8
0
3
6
9
PROG
/DOWN
BATT.
LOW
AC
PANIC
Model 116S
Motion Detector Alarm
System
Model 116X
Motion Detector Alarm
For IP Camera
BATT.
LOW
1
4
7
/ UP
2
5
8
0
3
6
9
PROG
PAUSE
ARM/
DISARM
PANIC
/DOWN
Model T015S
Wireless Security/Safety
Alarm With Auto Dialer
1
4
7
*/ UP
2
5
8
0
3
6
9
PROG
PAUSE
ARM/
DISARM
PANIC
/DOWN
Auto Dialer With Motion
Sensor & Alarm
Model T016S
Model 639S
Visitor Chime And
Watch Dog/Alarm
Model 600R
Wireless Receiver
LINE 1
Model 625R
Wireless Alert with
6 Sounds and Flash LED
Model 423R
Wireless Control
Lampholder
Model 621S
Wireless Outdoor Siren
With Flash Light
1
2
3
4
ARM/
DISARM
SIZE:140X200MM
P/N:610-615XX-000R
● 3 “AAA” batteries operation (not included)
● Battery low indicator LED
● Motion detection range up to 8 meters
● Motion detection angle up to 110 degree
Model T058VS/T058S
Wireless Securiy/
Safety Alarm System
With Auto Dialer
Model T068S
GSM/PSTN Auto Dialer
With Wireless Security/
Safety Alarm System
Model 528
Built-in Alarm/Chime/
Mute/Flash Led Light
Wireless Receiver
MODE
Model 527L/527F
Wireless Outdoor Siren
With Flash Light
Model 526L/526F
Wireless Outdoor Siren
With Flash Light
Model 422R
Wireless Control
AC Socket
Model 688R
Wireless Control
AC Socket