Users Manual Part 1

ManualsBrandsLeica Geosystems ManualsElectronicsPersonal Alert Tag

LED pattern Status Possible causes

18069_001

Right LED is per-

manently on in

green.

Charging is n-

ished.

n/a

4.1.5 Firmware update

CAUTION

Incorrect conguration by unqualied personnel

Incorrect conguration will render a tag inoperable, that is, not being able to

communicate with machine anchors. Thus, the tag will neither detect and

indicate nearby machines nor will nearby machines be able to detect the tag.

▶

Only an appropriately trained and qualied specialist may congure and

update the rmware of a tag.

To update the rmware of a pedestrian tag, use the designated slot of the

gang charger. See Fig. 14.

18165_001

Fig. 14: Gang charger interface for rmware update

a Programming slot

b Socket for power adapter

c Socket for programming cable

Firmware update step-by-step

☞

The CRS123 programming tool and the CRS107 programming cable

must be ordered separately.

Install the programming tool on your computer (Windows operating

system). Make sure that the rmware le for updating is available on

the computer.

1. Connect the power adapter of the gang charger to a suitable power

source.

2. Connect the gang charger to the power adapter.

The Power LED of the gang charger lights up green.

Connect the programming cable to the gang charger and to the

computer.

3. Insert the pedestrian tag into the programming slot.

Updating the tag rm-

ware

32 Operation

Summary of content (17 pages)

PAGE 1
LED pattern Right LED is permanently on in green. Status Possible causes Charging is finished. n/a 18069_001 4.1.5 Firmware update Updating the tag firmware CAUTION Incorrect configuration by unqualified personnel Incorrect configuration will render a tag inoperable, that is, not being able to communicate with machine anchors. Thus, the tag will neither detect and indicate nearby machines nor will nearby machines be able to detect the tag.
PAGE 2
☞ LED indication: As long as no firmware update is ongoing, the tag starts char• ging. The LEDs indicate the battery status and charging progress. If the tag has no firmware installed, both LEDs are permanently • on in blue. If both LEDs are permanently on in red, the tag might need a • hard reset. Refer to the section "Performing a hard reset". 4. Open the programming tool on the computer. In the bottom status bar, check if the tag is connected to the software. 5.
PAGE 3
4.2 Machine Anchor 4.2.1 General Working Information Cabin anchor functionality In order to reduce nuisance alarms, anchors mounted near the cabin of a vehicle can be assigned as cabin anchor (Anchor ID = 0). Cabin anchors suppress alarms for tags that are within the configured cabin anchor radius (Fig. 15). 18053_001 Fig.
PAGE 4
.2.2 Status Indicators Machine anchor status a b c e f g d 18052_001 Fig. 16: Status indication for machine anchor a b c d e f g LED off No Power LED flashing red quickly Anchor is starting up. LED permanently on in orange Anchor is powered up and running in standalone mode; no tags or other anchors are in range. LED flashing orange slowly Anchor is powered up and running in standalone mode; tags or other anchors are in range.
PAGE 5
a b 18054_001 Fig. 17: Indication based on the anchor configuration a b Alarm signals Single-anchor configuration: LEDs indicate only tag proximity Multiple-anchor configuration: LEDs indicate tag position and tag proximity Alarms to indicate proximity to a tag The iCON PA system supports three different detection zones. Each zone has a specific alarm signal which is clearly distinguishable from the alarms of the other zones. The following illustration applies to a multiple-anchor configuration.
PAGE 6
Obstacle collision alarms This feature requires an update of iCON PA10 to CAS (Collision Avoidance System). ☞ With CAS, the iCON PA10 system alerts machine drivers when they approach obstacles lying in driving direction. Such obstacles need to be pre-defined based on their location on site. Examples: Generic obstacle • Building • Bridge • Underpass • Powerline • "Stop" sign • Reduced speed area • Blast zone • Pantograph • Coal valve • Stockpile edge • 18398_001 Fig.
PAGE 7
18399_001 Fig. 20: Speeding alarm Panic alarm Persons wearing the pedestrian tag or using the LED display unit on a machine can set off a Panic alarm to indicate the need for help. When this alarm is displayed on the LED display unit of your machine, the person in distress is within close proximity to your machine. 18104_001 18105_001 Fig. 21: Panic alarm with unknown origin Indication of errors Fig. 22: Panic alarm with known origin The display unit performs a self check upon power-up.
PAGE 8
LEDs Subsystem Severity of error Description and possible cause Serial number Fatal error Invalid serial number. Contact support. Data port Alert Failed to send data port heartbeat message. GPS/ GNSS receiver Fatal error Unable to communicate with or to configure GPS/GNSS module. GPS/ GNSS antenna Fatal error GPS/GNSS antenna defective or bad connection. Power supply Fatal error Power supply defective or voltage too low/high.
PAGE 9
4.3.2 The Acknowledge Key Functionalities Acknowledging an alarm Machine drivers of machines on which the LED display unit is installed can acknowledge an alarm, thus silencing the audible signal. ☞ To acknowledge an alarm, press the acknowledge key once. Setting off the Panic alarm Machine drivers can set off a Panic alarm to indicate the need for help. The Panic alarm is displayed on all iCON PA display units within communication range, enabling drivers of nearby machines to render assistance.
PAGE 10
5 Care and Transport 5.1 Transport Transport in the field When transporting the equipment in the field, always make sure that you carry the product in its original container. Transport in a road vehicle Never carry the product loose in a road vehicle, as it can be affected by shock and vibration. Always carry the product in its container and secure it. For products for which no container is available use the original packaging or its equivalent.
PAGE 11
Cables and plugs Keep plugs clean and dry. Blow away any dirt lodged in the plugs of the connecting cables. Damp products Dry the product, the container, the foam inserts and the accessories at a temperature not greater than 40 °C and clean them. Do not repack until everything is completely dry.
PAGE 12
6 Technical Data 6.1 Dimensions Dimensions 6.2 Weight Type Dimensions [mm] (L x W x H) CRS101 machine anchor 151 x 81 x 45 CRS103 pedestrian tag 71.6 x 14.4 x 85.8 CRS113 LED display unit 81 x 30 x 20 CRS110/CRS111 main unit (without connectors) 81 x 30 x 126 CRS145 antenna 107 x 91 (Ø x H) Weight Type Weight [g] CRS101 machine anchor 170 CRS103 pedestrian tag 84 CRS113 LED display unit 60 CRS110/CRS111 main unit (without cables) 260 CRS145 antenna 620 6.
PAGE 13
Humidity Type Protection All products Maximum 95 % non-condensing To avoid the effects of condensation, periodically dry out the instrument. Protection against water, dust and sand 6.4 Type Protection All products IP67 (IEC 60529) Exception: Charger and AC/DC power supply Only operate in dry environments, for example in buildings and vehicles.
PAGE 14
6.5 Antenna specifications Main unit Other Technical Data Type Antenna pattern Typical accuracy Integrated antenna of CRS101 machine anchor Omnidirectional ± 20 cm over the temperature range Integrated antenna of CRS103 pedestrian tag Omnidirectional ± 20 cm over the temperature range Type LTE bands CRS110 1, 3, 4, 7, 8, 28 (EMEA, APAC) CRS111 2, 4, 5, 7, 17 (AMERICAS) 6.6 Conformity to National Regulations 6.6.
PAGE 15
transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p) is not more than that necessary for successful communication.This device complies with Industry Canada licenseexempt RSS standard(s). Operation is subject to the following two conditions:(1) This device may not cause interference.
PAGE 16
6.6.3 Dangerous Goods Regulations Dangerous Goods Regulations Many products of Leica Geosystems are powered by Lithium batteries. Technical Data Lithium batteries can be dangerous under certain conditions and can pose a safety hazard. In certain conditions, Lithium batteries can overheat and ignite. ☞ When carrying or shipping your Leica product with Lithium batteries onboard a commercial aircraft, you must do so in accordance with the IATA Dangerous Goods Regulations.
PAGE 17
878262-2.1.0en Original text Printed in Switzerland © 2019 Leica Geosystems AG, Heerbrugg, Switzerland Leica Geosystems AG Heinrich-Wild-Strasse CH-9435 Heerbrugg Switzerland Phone +41 71 727 31 31 www.leica-geosystems.