User's Manual

ManualsBrandsLeica Geosystems AG, CPD ManualsElectronicsBluetooth Laser Distancemeter

Table Of Contents

Display

Leica DISTO™ plus 1.0.0 GB

D5-Z1

function level

Display

D5-Z2

1 Laser "on"

2 Measurement reference (front/ stand/ rear)

3 Information

4Bluetooth

on/off

5 Display of the mathematical signs/operations

6 Main display (e.g. measured distance)

7 Distance measurement

8 Tracking

9Area/ Volume

10 min. Tracking

11 max. Tracking

12 Pythagoras function

13 Pythagoras function with partial height

14 Units with exponents (²/ ³)

15 Time symbol for time delay release

16 Save constant

17 Contact customer service

18 3 auxiliary displays (e.g. previous values)

19 SET

20 RESET

21 Battery display

22 2

function level

23 Recall stored constant (max. 10)

24 Recall last 15 values

25 Illumination (on/ off)

26 Beep (on/ off)

27 Offset setting

1 Distance measuring,

Tracking

10 Menu

- function level 1 or 2 11 Illumination

3 Meas. reference 12 Multiply [ x ]/ Timer

Release

4 Areas, Volumes 13 On/off key

5 Measuring 14 Clear

6 min. / max. Tracking 15 Mermory, Stack

7 Bluetooth

ON/OFF 16 Equals, Enter

8 Pythagoras functions 17 Minus [ - ]

9Plus [ + ]

198

18 delete 23 direction upward

19 enter 24 direction downward

20 direction left upward 25 direction right downward

21 direction left 26 direction right

22 direction left downward 27 direction right upward

109 11 12 13

2325 2127

22 18202426

Summary of content (13 pages)

PAGE 1
de 2 1 3 4 5 6 7 8 18 2nd function level 18 delete 19 enter 20 direction left upward 21 direction left 22 direction left downward 19 GB Display fr 9 it es nl ja 23 direction upward 24 direction downward 25 direction right downward 26 direction right 27 direction right upward 10 26 24 22 20 27 25 23 21 19 26 22 24 11 13 15 17 20 25 27 21 23 12 14 16 1 D5-Z1 function level 1 Distance measuring, 10 Menu Tracking 2 2nd - function level 1 or 2 11 Illumination 3 Meas.
PAGE 2
How to Use the Instrument 1st Function level Inserting / replacing the batteries Leica DISTO™ plus switching on/off 1 Depress the locking clip and slide end piece to the right. Briefly press. The illumination, Battery and Beep symbols are displayed until the first key press. The instrument can be switched off from any menu point. ) ) The instrument switches off automatically after 90 seconds if no key is pressed.
PAGE 3
de A second press starts the distance measurement. Possible settings Continuous measurement (Tracking) The result is displayed immediately in the selected unit. ) ) With the instrument on and the laser off, it is in "Normal Mode". GB With the laser on, it is in "Pointing Mode". appears on the display. Continuous measurement is started and the result is displayed. Press to end Tracking Mode. Last result is shown in the display.
PAGE 4
Time delay release Instrument must be in Pointing Mode. Press and hold until desired time delay has been reached (max. 60 seconds). de Press to toggle between the functions. Calculations Area Press until GB appears on the display. Once the key is released, the remaining seconds (e.g. 59, 58, 57...) are displayed, until measuring. The last 5 seconds are counted down with a "beep". After the last "beep", the measurement is made and the value displayed. Example: Measuring without any key activation.
PAGE 5
de ) Selecting units (menu) Selectable units: fr it After making/changing settings, it is imperative that a test measurement is performed. blinks on the display. "Clear Entry" may also be used (e.g. to cancel a selection). GB ) Call up menu point. Confirm selection, reset to Normal Mode. – m (mm) = 0.000 m – 14’ 06’’ 1/16 = ’ ’’ 1/16 – m (cm) = 0.00 m – in = 0.0 in – ft = 0.00 ft – in 1/16 = 0 1/16in – ft in 1/16 = 0.
PAGE 6
starts to blink on the display. With key [+ / -] adjust value as desired (e.g. from 2.297m to 2.300m). For larger steps press and hold additionally. Press to adjust unit (²/³). ) The adjustment is for m, m² and m³ rsp. ft, ft² and With key [+ / -] select desired mermory (1 to 10). Confirm; value is ready to be used for (e.g. calculating an area) or Recall last measured value (Stack) Briefly press twice and the last value in the display is shown. Confirm. With key [+ / -] select desired value (max.
PAGE 7
de Determine maximum dimension, e.g. to determine the (room) diagonal. Press until GB fr appears on the display. Move the Leica DISTO™ plus a large amount around the target point. Activate continuous measurement with a brief press. it Slowly rotate the Leica DISTO™ plus to the right/ left past the corner. Stop continuous measurement. es The largest measurement is displayed (e.g. 12.314m = diagonal of room).
PAGE 8
) With each of the distance measurements you can use: • a simple distance measurement, • a value from stack/ mermory or • a measurement with time delay release. ) ) For short distances, a good base behind the instrument is sufficient for mechanical alignment. You will obtain the best results if the Leica DISTO™ plus is rotated around a fixed point (rear edge, thread position) and the axis of the laser beam passes through this axis.
PAGE 9
de GB fr Move the Leica DISTO™ plus a large amount around the ideal measurement point. Stop of continuous measurement. Press until Value is accepted and and on the display "3 ---" starts blinking. Aim at the lower point (3). Aim at the upper point (1). Only in the second level can measured values be transferred or corrected with the Leica DISTO™ plus. The type and number of functions that can be activated in the second function level depend on the software used.
PAGE 10
Switching off the Bluetooth® ) The direction arrows Press the arrow key briefly. A a thin line will be drawn to scale. Before switching off the Bluetooth® , always change to the first function level Briefly press. ) de Transfer of the measured values GB Bluetooth® is switched off,when this icon is no longer visible If still in the second function level, the Bluetooth® cannot be swictched off. This is a safety precaution to prevent an accidential interruption of the Bluetooth® connection.
PAGE 11
de Press briefly to confirm that the correct line was drawn. The line is then drawn thicker with the measurement dispayed. Press briefly to clear a wrong line. GB fr . Is the measurement is still displayed in the Leica DISTO™ plus, it can be transferred again by pressing the correct arrow key. Other functions are described in the manual of the software used.
PAGE 12
Wet, smooth or high-gloss surfaces 1 Aiming at a "Acute" angle deflects the laser beam. The Leica DISTO™ plus may receive a signal that is too weak (error message 255). 2 If aiming at a right angle, the Leica DISTO™ plus may receive a signal that is too strong (error message 256). With measurements from a distance of 25 m the laser spot is in the centre of the crosshairs. Below a distance of 25 m the laser spot moves to the edge of the crosshairs. Inclined, round surfaces Can be measured with the laser.
PAGE 13
de * Maximum deviation occurs under unfavorable conditions, such as in bright sunlight or when measuring to inadequately reflecting surfaces. For distances over 30m-without using a target plate- themaximum deviation may increase by ±0.1mm to maximum ± 10mm. For more information, refer to www.disto.com. GB ** As of 100m the measuring units are displayed in cm. *** Reduced when using the fr Bluetooth® function Message Codes Error message it appears beside the message number on the display.